Thank you! I have a Hewescraft 180 pro v with a 115 Honda
@fairplayfishing
3 ай бұрын
Nice boat I have a Sea Runner
@fiberopticsguy
Жыл бұрын
Good video, exactly what I needed. Thank you!
@fairplayfishing
Жыл бұрын
Much easier than you would think. A great do it yourself project. You might want to think about changing the gear oil on the lower end while the lower drive is off. Easier to do with the help of gravity.
@matthewd.3276
9 ай бұрын
me too....just got mine....love the motor and boat.
@mitchellcroney6304
Жыл бұрын
Very well done video 😊
@fairplayfishing
Жыл бұрын
Thanks hope it helped
@donfisher8624
2 ай бұрын
You forgot to mention hidden bolt after you take out the trim piece
@fairplayfishing
2 ай бұрын
Thanks I’ll fix that, good catch
@matthewd.3276
9 ай бұрын
Exactly what i needed. Is the thermostat in the lower unit? How often do you need to replace your thermostat? I just got boat and dont have a manual. Thank you!!!!
@fairplayfishing
9 ай бұрын
Thermostat is right on top very easy to get to. If your in salt water I would check them annually. Have replacement on hand so it can be replaced if showing signs of corrosion. You can put them in boiling water to see if they open up. Add some salt away to the boiling water to clean any salt residue. All very easy to do. Hope this helps.
@guillermorodriguez1071
4 ай бұрын
Necesito desarmar un outboard HONDA 150HP BF150 FOUR STROKE YEAR 2006modelo
@fairplayfishing
4 ай бұрын
gracias por el comentario
@Mark-dj5qf
3 ай бұрын
Were you able to get the lower unit back up by your self? Thanks
@fairplayfishing
3 ай бұрын
Yes the trick is to have the motor raised up enough to thread the shaft in and have a five gallon bucket ready to hold put under the lower unit to hold it in place as you align the rears use the trim tilt to help but if you ca get help it can’t hurt especially the first time you try.
@khaosic424
Жыл бұрын
The keeper (key) that almost fell out. I didn't see that when assembling again. Is that tricky?
@fairplayfishing
Жыл бұрын
Sorry I didn’t get back to you sooner. You probably have solved this already. The key slips back into place easily use a little marine grade grease so it will be be as easily removable next time.
@tomhuynh7556
Жыл бұрын
You changed the impeller after how many hours that motor ran? Was it 200 hrs or more?
@fairplayfishing
Жыл бұрын
200 hours would be on the outside for sure after 100 start planning. And time is also a factor if your not running it a lot at least every two years. If the impeller gets brittle it could have pieces break off and go places that would result in some costly repairs. Better safe than sorry. And not too difficult to do the maintenance.
@dmanars1
Жыл бұрын
what did you torque the water pump housing at? I feel Im going to break it torquing ir to 120in/lbs
@fairplayfishing
Жыл бұрын
I’m seeing the housing bolts specked at 14 Foot/pounds www.manualslib.com/manual/2023987/Honda-Bf135a.html?page=18#manual
@dmanars1
Жыл бұрын
@@fairplayfishing Thanks! I couldnt find it in the manual I had
@Meal_Team6
Жыл бұрын
You got a part number for that kit?
@fairplayfishing
Жыл бұрын
06192-ZY6-000 You can chat with them to confirm it is the correct one for your motor
@Mark-dj5qf
3 ай бұрын
Thanks, what’s the length of yours?
@fairplayfishing
3 ай бұрын
19’ ET where are you fishing out of? I’m central California
@Mark-dj5qf
3 ай бұрын
Northern California.
@fairplayfishing
3 ай бұрын
I was fishing Shasta and Whiskeytown beginning of the month had great success and nice size Kokanee
Пікірлер: 30