This was really well explained, and actually easy to follow for a beginner. Thank you very much!
@joesmith-je3tq
10 ай бұрын
You're welcome.
@Scorry
10 ай бұрын
High-quality content and detailed explanation, as usual. Thank you!
@joesmith-je3tq
10 ай бұрын
You're welcome.
@DM-fz3ly
10 ай бұрын
Very interesting Joe! and it is clear you have a lot of experience in measurements and RF. You also can teach as I followed a lot of your discussion. When you mentioned that the mismatch on one input would reflect back through the splitter and affect the signal going into the other channel it really rang a bell with me in how there are just so many pitfalls in RF measurements that only someone with a lot of experience, and likely having made a few mistakes along the way, would know. Thanks for sharing your knowledge!
@joesmith-je3tq
10 ай бұрын
You're welcome.
@johnwest7993
10 ай бұрын
Thanks Joe.
@joesmith-je3tq
10 ай бұрын
You're welcome.
@jaro6985
10 ай бұрын
Good video, I guess no commercial 50 ohm terminators sold by scope manufacturers do this? I didn't see any from a quick search.
@joesmith-je3tq
10 ай бұрын
Custom match them to a specific scope? Not that I am aware of.
@egonotto4172
9 ай бұрын
Is the book you use Introductory Circuit Analysis by Robert L. Boylestad and Brian A. Olivari?
@joesmith-je3tq
9 ай бұрын
Sounds right. It's a pretty old book.
@otherbasis8505
10 ай бұрын
Tek made a probe (before my time) P6048. That's a probe for 1MOhm scopes that behaves akin to a resistive probe for 50ohm scopes. It is described in their "Oscilloscope Probe Circuits" publication. They get the bandwidth by terminating into a T-coil, with an adjustable cap to augment scope's input capacitance. If one starts adding inductors to their terminations, why not go full monty? 😁 [EDIT:] Crunched some numbers: T-coil is conceptually clean and can be matched to the cable. Soo... If, for example, cable is .21uH/m and 83pF/m then 16pF cap corresponds to 40nH, i.e. two 20nH inductors (and a 50 ohm resistor to the ground, of course).
@joesmith-je3tq
10 ай бұрын
They claim under a pF tip capacitance but only 100MHz BW and only a 2.5ns Tr. I wonder how well it actually performs. In that link to Lasmux's active probe project in the description, I had compared several of my probes. You can see how the PP005 probe I showed in this video compared with a resistive probe. The cross over point was around 60-70MHz. www.eevblog.com/forum/testgear/12-ghz-active-probe-project/msg4988716/#msg4988716
@Graham_Wideman
5 ай бұрын
0:40 Your through terminators with the SMD resistors look like a very nice electrically helpful geometry. However I would worry that one side being attached to the pin would subject the resistors to mechanical stress during plugging/unplugging, possibly cracking them, disconnecting them, likely intermittently. That sort of problem might go unnoticed -- quite annoying. It we be so nice to somehow create a more flexible connection to the resistors -- though I don't have any ideas how to do that at the moment.
@joesmith-je3tq
5 ай бұрын
There were a few clues in this video that I left for the savey viewer to sort. The inductance of the TH resistors may improve the match. Using these leaded parts also mitigates the stress you mention. Consider that when we are talking about using it with a scope, each one would be different and require a different network. Even if you happen to compensate it correctly, the improvements most likely will be minimal. I basically suggest better tools may be the best solution.
@Graham_Wideman
5 ай бұрын
19:57 "so just adding this termination resistor has greatly improved the flatness of this" -- I'm not seeing the improved flatness. The knee appears to be in the same place. Which aspect of the curve is flatter? I'm sure I'm missing something here. Hmm... by "improved flatness" do you mean the better ratio between say 1 MHz and 350 MHz? No resistor: 1 : 0.494 = 2.02 versus with resistor: 0.5 : 0.375 = 1.33?
@albertolopez7420
10 ай бұрын
Hello, I really enjoy the channel’s content! Could you share boylestad’s book title? I would like to take a glance at it, looks like a good reference. Thank you!
@joesmith-je3tq
10 ай бұрын
Sure, it's "Introductory Circuit Analysis" It only covers the the basics.
@ivolol
9 ай бұрын
Guess we all just need to own lecroy oscopes...
@joesmith-je3tq
9 ай бұрын
Or just buy tools that do the job you need them to.
@gorak9000
10 ай бұрын
12:00 I think you mean an E8357A, not an E8557A - E8557A isn't a valid agilent product
@joesmith-je3tq
10 ай бұрын
That is correct. I'm surprised that's the only mistake you caught as long as the video is. Normally there are a few.
@jdmccorful
10 ай бұрын
@@joesmith-je3tq the big picture😁
@jdmccorful
10 ай бұрын
Thorough and enjoyable. Haven't seen that textbook in over 40 years.Thanks for your time!
@joesmith-je3tq
10 ай бұрын
I had a friend who was interested in circuit design and I came across a used copy in a book store that I gave to them. It's a good starting point.
Пікірлер: 29