I also agree. The water level is not to be that low. Keeping the water level at its maximum will allow the AC to restart in case of power outage. Aquaclear…the best filter in the market!!!
@lkapitan8232
3 жыл бұрын
Thanks Jose.
@TealStarLight5
3 ай бұрын
Tyvm for this! Especially the power outage info. Luckily i got a portable power station lumpar 600 on deck ready at all times
@dickrose219
3 жыл бұрын
i have modified mine to use intake strainers from a fluval 407 canister filter because they have a check ball in them. when power goes off it doesn't drain back any water, regardless how low your tank gets. i.e. doing water changes , ect. the u-tube, lift tube and the filter stays full so my bio media doesn't get dry, when i plug it back in, it starts instantly. i have pics of how i modified it if you would like
@lkapitan8232
3 жыл бұрын
Dick, that is brilliant, never thought of that and I use Fluval canisters. You should post a video of how to do that. I'm sure it will get much attention. Thanks.
@hardybryan
2 жыл бұрын
Same size tubing, I assume? Is the flow loss noticeable?
@dickrose219
2 жыл бұрын
@@hardybryan no flow loss on ac 20 to ac 70. the 407 strainer is designed for up to 383 gph so there is a slight flow loss on the 110. as far as size, the 20,30,and 50 you just cut off the strainer from the inlet tube and press on the new strainer, it's a tight fit, but goes right on. for the 70 you need to come up with a bushing, i used a piece of fluval canister hose end. i can send pics if you like
@hardybryan
2 жыл бұрын
@@dickrose219 Thanks. That's so cool. I have so many spare filter parts, but it never occurred to me to use a check valve there. I'm going to give it a try. I'm 90% sure I still have all the parts from my old 404 that died a couple years ago.
@meminustherandomgooglenumbers
9 ай бұрын
Upload how to vid plz 👍
@tff1293
2 жыл бұрын
Great video. And even if priming is an issue, these are just incredible filters, you just need to pay closer attention and keep your water high. Right now I'm running a 55 gal and a 60 breader, each with 4 aquaclear 50s (means I'm running about 800 gph on each and turning each tank 13-15 times per hour). On each tank, 2 filters have sponge media all the way to the top, and the other 2 are full of loose bio stones (like you have here). Never have priming issues, they're a breeze to clean, and very quite as long as my water level is high. Only noise is the lids will occasionally rattle but a quick touch and it goes away
@lkapitan8232
2 жыл бұрын
Thanks
@josephdonnelly3169
2 жыл бұрын
Nice content, very helpful. I’m running fluval aqua clears on all my tanks…
@lkapitan8232
2 жыл бұрын
Thank you
@jagsr5168
Жыл бұрын
Me either and thank you for testing this for me that's what I needed to know because I kinda felt like the feed back was wrong about this filter..now I truly know what not to do
@lkapitan8232
Жыл бұрын
You are welcome, and thanks for watching.
@aheimsvensson1573
2 жыл бұрын
Thanks for clearing that out for everyone👍
@lkapitan8232
2 жыл бұрын
You're welcome
@jmsadms
Жыл бұрын
Yes good to know. It's not a problem for a power outage, but it's another step during a water change to remember to fill the filter before plugging back in. Also, what I like about the Fluval C Series HOB, is you can remove each media compartment separately and clean one at a time without unplugging it.
@tayson1222
2 жыл бұрын
I've been using 3 AC110 on my 125 gallon tank for over 10 years now, never had an issue . Like you said they hold a lot of media . My only complaint about them is the sound, they are too loud "Rattling sound" annoying, but they are so damn good at keeping my tank clean and hold tons of media and I use them to polish the water by adding poly fill . No hang on the back filter does a better job . I heared the tidal 110 is good . Watched some videos about them and looked into the way they operate, they seem to be well made, might be a good option as well. If one of my AC breaks I might get a tidal to try it . I like the fact that the motor is in the water
@lkapitan8232
2 жыл бұрын
Funny you bring this up as I was going through this with two AC70's, one was quite and one sounded like a train. Turned out it was the impeller shaft, it was old and worn and allowed the impeller to wobble as it spun. Replaced the shaft and now they sound the same. Might want to look at the metal shafts on your AC100's. Checked out your channel, love those cichlids.
@tayson1222
2 жыл бұрын
@@lkapitan8232 thanks for checking out my Channel. I haven't posted a new video in a long time . I will soon . Ac110 is loud no matter what you do to it. Even when it's brand new . I tired everything. Don't get me wrong I love them and still use them they are my favorite.
@alejandrovargas7592
2 жыл бұрын
Thanks for the useful demonstration.
@lkapitan8232
2 жыл бұрын
You are welcome.
@dfisherii
3 жыл бұрын
Great! Thanks for making this video.
@lkapitan8232
3 жыл бұрын
You are welcome.
@pendlera2959
3 жыл бұрын
I think it depends on the model of the filter. I've had occasional issues with my AC 30 if I've slacked on top-offs and the water is 1" down or so (can't remember exactly; it's been a while). However, a more frustrating problem is how even if the water level is okay, sometimes the impeller doesn't work right when it restarts. You have to remove the intake tube and jostle the impeller with your finger to get it going.
@lkapitan8232
3 жыл бұрын
I have also had the same problem and if I remember right it was a worn impeller shaft. Changing out the shaft is a challenge as that thing is in there tight.
@100bgeagle
2 жыл бұрын
How about cleaning the impeller and shaft!!! It builds a slime that sometimes sticks to the impeller.
@jimsvo4486
3 жыл бұрын
I agree, I keep my water level very near the top, and I never had a power outage issue restarting on my two 110s and one AQ70, so it must be only for people that have low water levels or maybe it also relates to the depth of the intake tube.
@lkapitan8232
3 жыл бұрын
Thanks Jim.
@bobbysauer7826
Жыл бұрын
my aqua clears always restart after outages my fluval c series needs me to bump the propeller back down after outages tho
@victorl8163
2 жыл бұрын
Thank you for telling us the truth, unlike all the popular channels out there that are sponsored by seachem tidal who put aquaclear down,in my opinion I've had both brands and the aquaclear filters are solid, the tidal series are all gimmicks.
@lkapitan8232
2 жыл бұрын
You are welcome, and I agree, I have also had both and I don't get the Seachem craze,
@samfru1
2 жыл бұрын
I am an Aquaclear fan. I currently run an AQ70 on my thirty five gallon and an AQ30 on my ten gallon in addition to running several Fluval canisters. What I find is that many times (not every time) that my AQ70 is unplugged the little white plastic impeller becomes unseated and the filter wont restart unless I can manipulate the impeller into place.
@lkapitan8232
2 жыл бұрын
Sam, I don't follow. What does unseated mean?
@samfru1
2 жыл бұрын
@@lkapitan8232 So I am referring to the small white plastic impeller. If I unplug the filter during a water change, sometimes that impeller will shift slightly and when I plug the unit back in it doesn't restart. I have to manually manipulate the impeller with a little stick to get it to restart.
@lkapitan8232
2 жыл бұрын
@@samfru1 I understand now. Is that true even when the impeller is clean? Because that also happens to me when I don't clean the impeller.
@samfru1
2 жыл бұрын
@@lkapitan8232 do you think that what causes it? It is possible I guess. I suppose that most times I unplug the filter it is during a water change and so it is probably dirty.
@lkapitan8232
2 жыл бұрын
@@samfru1 I do, those motors are very weak, only 9 watts, and a little muck will stick them for sure. Next time pull it out and give a quick rinse see is that matters.
@ajw9975
2 жыл бұрын
As long as the water level in the tank is higher than the filter end of the intake tube (in the filter itself), you're good. Any lower and that's where the air will enter.
@zackhaas3267
9 ай бұрын
I have a AC 110 and an AC 70, and they both hold their prime as long as the water level is not too low. My AC 70 can be down an inch and still restart fine.
@therandomman6647
2 жыл бұрын
I've been trying to make the water level point for so long!
@dhiyaesmail1297
Жыл бұрын
How often does the impeller have to be cleaned?
@lkapitan8232
Жыл бұрын
These motors are very weak, so every 2 months will keep them running great.
@trevormcmanis
2 жыл бұрын
Your Handle? Rush Hour 2 reference?
@melerwin1
2 жыл бұрын
I have if I'm breeding apple snails.... They lay the eggs up on that top portion. I'm not against an AquaClear... I've used them on my smaller tanks.
@hardybryan
2 жыл бұрын
The 110's will refill with a 'full' tank. 70's and 50's have a good shot too, though I doubt they'd pass the 1 inch test. The smaller ones can struggle even with a full tank. I love Aquaclears. They are outstanding filters and I have them on 2 of my 4 tanks right now. But I always make sure SOMETHING, even if it's a sponge, is running that will 100% come back on immediately with the power. This is a legit issue. If you travel even a little frequently, you're likely to have experienced coming home to the water level in the tube just bobbing up and down but not quite getting to the top. And if you have it on ANYTHING but full flow, there is a 0% chance of it self priming even with a full tank. Again, these are great filters, just don't blow off this issue like it's nothing. Trust me, it's not.
@josephtavares8178
2 жыл бұрын
Tried Emperors and Tidals. STILL LOVE aquaclear 110s OVER any else Never HAD a problem i n 15 years, Still the BEST Hang on hands down media wise, and can use in aquaterrariums and paladariums. CAnnot do that with the tidals and emperors. I have run them in turtletank 3/4 full no problems ever.
@lkapitan8232
2 жыл бұрын
Me too
@wannabe_D7000
2 жыл бұрын
Does filter pump suck poop or just filters a water ? New here please help
@lkapitan8232
2 жыл бұрын
Your question is losing something in translation, but I will try. A proper aquarium filter contains mechanical, chemical, and biological media. The mechanical media traps fish waste, uneaten food, anything floating in the water. The chemical (typically carbon) removes unwanted organics. Biological media breaks down toxic fish waste (ammonia) into a less toxic form (nitrate). Is that what you are asking?
@wannabe_D7000
2 жыл бұрын
@@lkapitan8232 i have this filter with bubbler in it if i use one point for filtration and other one for bubbler then it kinda cycles the water inside the tank but if i close one point and only use the filter then it doesnt suck the poop like it use to but the shopkeeper told me to use one point for better filtration .. im confused ….
@lkapitan8232
2 жыл бұрын
@@wannabe_D7000 I am also confused, I do not know what you are describing. Click on my name, go to the ABOUT tab on my channel page and send me an email with a picture of the filter, only way I can help is to see it.
@wannabe_D7000
2 жыл бұрын
@@lkapitan8232 didnt find your email … :(
@shanedwood
2 жыл бұрын
It will also start after an outage if the impeller is clean
@lkapitan8232
2 жыл бұрын
I agree.
@100bgeagle
2 жыл бұрын
Yes sir, so you must clean impeller ever time you service or it might stop!!
@chicagosveryown7776
3 жыл бұрын
I agree 100% i run aquaclears on ALL of my tanks & I’ve NEVER had a problem with them not restarting.The only way that’s possible is if the water level is too low or the impeller is too dirty.The only problem I’ve had with aquaclears is the rattling of the lids.I hate that….
@lkapitan8232
3 жыл бұрын
I bet 1000's have complained about those rattling lids and they never change, else I agree a very good filter , thanks
@chicagosveryown7776
3 жыл бұрын
@@lkapitan8232 yup those lids are a problem that Fluval should address but other then that it’s still the best filter on the market.👌🏾
@mikez2501
2 жыл бұрын
You guys must be lucky. Been through 2 AC70s and a third propellor. Did a water change just yesterday, tank filled to the brim. Came home from work and the filter wasn’t working at all. Propellor stuck and not spinning and it NEVER primes itself regardless of water level. I have to dump water into the filter every time. Plus it’s stupid loud with that stupid lid. Currently looking for another unit.
@chicagosveryown7776
2 жыл бұрын
@@mikez2501 does your tank have sand or gravel?
@mikez2501
2 жыл бұрын
@@chicagosveryown7776 sand, and the bottom of the intake it 5-6” off the bottom. After it stopped yesterday I took it apart the check the impeller and it was clean with no debris in it or around it.
@agrant4701
2 жыл бұрын
I have 2 110s on my 75 gallon and I do not see the need for more filtration. Because someone won’t stop chirping about canisters, I am going to obtain one; however, I really love the Aquaclear. I think it’s funny when people try to politely slam Fluval about the issue. They start acting weird when they put the company down: It’s hilarious. Anyway, I am going to buy another filter like asshole; however, the Aquaclears are great. I almost do not know why I am getting an FX4. Lately, I have been thinking about getting a used one-because I just cannot justify it. My water is crystal clear!
@lkapitan8232
2 жыл бұрын
I agree, Aquaclear's are great. Your water is crystal clear because you are getting 1000 gph /75 gallon = 13 times turn over per hour, which is awesome. Canister filters have their place, they are very quite and hold a lot of media, but in most cases not needed. Thanks for the comment.
@sam3d
Жыл бұрын
My 2 AC 70s alway restart without priming when I change water. Man I want 110 so bad! Too bad they're $100 now
@lkapitan8232
Жыл бұрын
Not sure why the AC 70 does and the AC 110 does not. As for the cost, think about it like this - a properly maintained AC filter can last for 20 years, so $100 over 20 years is not much. Thanks for watching.
@therandomman6647
5 ай бұрын
"In defense of" about the undisputed champion of HOB filters. The Tidal 110 is doodoo in comparison to the aquaclear 110 for the reasons you mention in this video.
@c.bishopyoung1459
2 жыл бұрын
Mine restarts fine.
@edgarrivera6012
9 ай бұрын
Fluval 07 series rules!
@armanduval.83
3 жыл бұрын
The problem is more recurrent with AC 70 regardless the water level though.
@lkapitan8232
3 жыл бұрын
Why is that? I currently run 2 AC70's and they restart every time.
@armanduval.83
3 жыл бұрын
@@lkapitan8232 Apparently many of them don't. A lot of people have reported this to happen, me included. Perhaps there were somo batches with this defect.
@lkapitan8232
3 жыл бұрын
@@armanduval.83 That is interesting, I did not know that, thank you for replying.
@100bgeagle
2 жыл бұрын
Impeller must stay clean!!
@armanduval.83
2 жыл бұрын
@@100bgeagle In this case this this happens whether or not the impeller is clean.
@100bgeagle
2 жыл бұрын
Sorry but you can lose prime in a power outage,but it's never became a problem for me as I know too look! I always have my water level near capacity!!!! Also just too loud for the living room. Lastly I changed out for a second cannister filter with more mechanical and biological processes!!!!
@SG-Cichlids
2 жыл бұрын
The best hob on the market. The only thing they could do to improve is put the pump in the tank like the tidal. Best thing about it is all the room for media. Instead of putting bio rings or other ceramics put another 110 sponge in it. The sponge is the perfect ppi for brien bacteria and grows far more bacteria than ceramics and that is true for all the ceramics. Doesn't matter how cheap or expensive sponge is better.
@lkapitan8232
2 жыл бұрын
Sorry took so long to reply, somehow I missed it. I read that somewhere that sponges hold more bacteria that ceramics, I see an experiment in my future. Thanks.
Пікірлер: 82