A very good and informative video on the bit set. Just a tip for those new to woodworking and raised panels you should always rout each end of the end grain of each panel every time before cutting the side grain. That way any tearout when routing the end grain will be removed when routing the side of each panel.
@andyaarav2401
3 жыл бұрын
I guess im asking randomly but does someone know of a trick to get back into an Instagram account..? I stupidly lost my password. I love any help you can give me
@caleblyric7560
3 жыл бұрын
@Andy Aarav Instablaster :)
@andyaarav2401
3 жыл бұрын
@Caleb Lyric i really appreciate your reply. I got to the site thru google and Im in the hacking process atm. Looks like it's gonna take a while so I will reply here later when my account password hopefully is recovered.
@andyaarav2401
3 жыл бұрын
@Caleb Lyric It did the trick and I now got access to my account again. I am so happy! Thanks so much you saved my account!
@caleblyric7560
3 жыл бұрын
@Andy Aarav you are welcome :)
@dannysiwale787
Жыл бұрын
Am kindly asking why my raised panel bit can not fit on my Bosch GOF 130.
@InfinityTools
Жыл бұрын
The Bosch GOF 130 comes with an 8mm collet, The shank of these bits is 1/2"
@U2BER2012
7 жыл бұрын
Is there any reason why I couldn't just position the fence back in small increments, whenever it's time to move the panel in to get a deeper cut, instead of changing out the bearings?
@InfinityTools
7 жыл бұрын
Yes, you can certainly use the fence to limit your depth of cut when using our raised panel with backcutter router bits and making a square door. However, if you plan on making an arched top door by following a template then you wont be able to use the fence as a depth stop. You'll need to change out the bearings and make several passes. Hope this helps.
@U2BER2012
7 жыл бұрын
Okay, thanks!
@syeedishfaq4600
5 жыл бұрын
Nice
@CarlsontheOutdoorsman
7 жыл бұрын
Can you use these bits with standard routers on the market? Or do I need a much larger size router for these size bits?
@InfinityTools
7 жыл бұрын
Larger router bits, in height or diameter, will work best with routers of at least 2.5 h.p. Of even greater importance is the need for the router to be variable speed. You can't run a horizontal raised panel router bits in a single speed router, you'll need to have those larger bits spin at around 13 or 14k R.P.M. A good router bit speed chart is below, copied from newwoodworker.com Suggested Maximum Router Bit Speeds Bit Diameter Maximum Speed 1" 24,000 RPM 1.25 to 2" 18,000 RPM 2.25 to 2.5" 16,000 RPM 3 to 3.5" 12,000 RPM Suggested Speed Chart courtesy Infinity Cutting Tools. Remember that these are SUGGESTED maximum speeds! Your equipment and/or situation could require much lower speeds for performance and safety! The full article on bit speed can be found here www.newwoodworker.com/rtrbitspds.html -David
@CarlsontheOutdoorsman
7 жыл бұрын
Thanks for the reply! I appreciate it.
@wanlisa9360
7 жыл бұрын
what is the size of router bits used ....?
@InfinityTools
7 жыл бұрын
The Infinity raised panel router bits with backcutter are 3-1/2" in diameter and have a 1/2" shank.
@wanlisa9360
7 жыл бұрын
okay thanks the info .
@kashmirbeautyandfoods7414
6 жыл бұрын
How can I buy this infinity raised panels router bits?
Пікірлер: 22