Yeah it stuck right to the dam and wanted to go. I’m more than sure it will make it to the top…as long as I put loctite on the wheel nuts.
@brianellison3525
2 жыл бұрын
You know, you can drastically lower the weight center and load up the front axle by swapping the battery and the esc location. Get rid of the rear tray completely, and pinch the esc between the rails with foam tape. The front tray can be trimmed to hold the battery down low in the frame in front of the motor. I also removed the front bumper, and the rails in front of the shock mounts for more servo travel. Then body mounted the lights. Be well, and have fun.
@ReadytoRunRC
2 жыл бұрын
I'm getting the Mofo Ugly AF chassis to move everything around. My front bumper is gone too when I did the four link. Thanks for watching!
@wvflying1626
2 жыл бұрын
That is so darn awesome. Love everything about it.
@MightyistheRCGamer
2 жыл бұрын
Your right the red links look so much better and I am not just saying that
@ReadytoRunRC
2 жыл бұрын
I am really liking the look of those red links.
@dronereviewman9580
2 жыл бұрын
I like this one a lot!!! Been so long since i have had any r.c. car or truck!!! Great Review!!
@JoeOvercoat
2 жыл бұрын
When tightening your steering servo horn, you can hold the horn with your fingers, so that you can get that last little bit of torque onto the screw in a controlled way…aka snug. P.S. Shoutout to INJORA!
@ReadytoRunRC
2 жыл бұрын
I didn’t want to over tighten. The servo holds its position pretty good that I felt it was snug enough. Yes shout out to Injora!
@JoeOvercoat
2 жыл бұрын
@@ReadytoRunRC yes, if one turns lightly until the servo starts to give that prevents stripping out the delrin. an especially good idea at this scale.
@rcjungle7645
Жыл бұрын
Thank you 😎👍
@slowerlowerrc
2 жыл бұрын
The camera doesn't do any justice for the angle of that dam, or the height. I'm sure it is massive in person!
@ReadytoRunRC
2 жыл бұрын
It's 100 feet high. It's pretty tall and yeah it doesn't do it justice.
@SomeStrangemysterious
8 ай бұрын
I wouldn’t suggest doing any grinding on the motor shaft of your motors. Because metal shavings are likely to end up sticking to the magnets inside the motor.
@wingnutbert9685
6 ай бұрын
Masking tape over the holes. 🙂👍
@rcpatienceraw9751
2 жыл бұрын
Great video. Rig is lookin really good. Could be me but watching your tires. Still looks like you have bent axle.
@ReadytoRunRC
2 жыл бұрын
Thanks. It came a long way. I think you’re right about the axle. The front left has a little wobble to it.
@rcpatienceraw9751
2 жыл бұрын
@@ReadytoRunRC ive been going threw the same thing.. im finally going to just spend the money an get yeah racing axles. Even though it will cost me more for shipping then the product itself lol.
@ReadytoRunRC
2 жыл бұрын
@@rcpatienceraw9751 that was the first I ran it since it fell off the ledge. I only noticed wobble when I was editing the video. I still have the fronts from the axle kit I bought so I’ll swap them out before I climb the dam. Shipping rates are the worst.
@hellofromsoutheastalaskarc7517
2 жыл бұрын
Hello from southeast alaska how's it going today bro
@ReadytoRunRC
2 жыл бұрын
Hello!
@tcboffroad3206
2 жыл бұрын
So when pulling back on the throttle control and if it did go in reverse and you want it to go forward when pulling back couldn’t you just change directional on remote?
@ReadytoRunRC
2 жыл бұрын
I’m not sure where there’s anything on the remote that changes the direction for throttle control. The only thing I see that you can reverse is for channel 1 which is for your steering servo so you can have reversed controls for steering.
@tcboffroad3206
2 жыл бұрын
@@ReadytoRunRC man you are correct I have several scx24’s and the Jeep gladiator does have throttle reverse on the remote so when I made my comment I assumed they all had it..lol. I’m throwing portal axles on a few and the portals run in reverse so the gladiator is just a matter of flipping a switch but on the c10 and deadbolt I’ll have to do your method. Sorry for the confusion.
@ReadytoRunRC
2 жыл бұрын
@@tcboffroad3206 that’s ok. Wish it was that easy with the older SCX24’s. I haven’t had my hands on any of the newer version SCX’s. Have fun with your build.
@crazymimi9523
2 жыл бұрын
Awesome
@rcpatienceraw9751
2 жыл бұрын
Did you ever go back and see if you can make the climb to the top?
@ReadytoRunRC
2 жыл бұрын
I didn’t. But I am going to try very soon. Maybe even this weekend.
@dustinrossi9384
2 жыл бұрын
How'd you break all that stuff..? Is it because the weight?
@ReadytoRunRC
2 жыл бұрын
No it fell off a ledge into water.
@Funcentric
2 жыл бұрын
Thanks for your video. Would you mind sharing why you went with the 66t version vs the 50T?
@ReadytoRunRC
2 жыл бұрын
Really I just wanted to test it out. See how it compared to the barrage motor. The barrage motor died so it gave me the chance to run this one as a replacement.
@Funcentric
2 жыл бұрын
@@ReadytoRunRC how do you like it and what’s a barrage motor?
@ReadytoRunRC
2 жыл бұрын
@@Funcentric I like it a lot so far. Seems to have plenty of power. A barrage motor is the motor that comes stock on the ECX Barrage. A lot of people were swapping that motor with the stock SCX24 motor because it was a much better motor.
@Funcentric
2 жыл бұрын
@@ReadytoRunRC I see. Okay. Cool. Thanks for the clarification.
@aiizen_pr
2 жыл бұрын
Nice thinking about getting one for my nieces rc what top speed does this make to see if it is not to fast
@ReadytoRunRC
2 жыл бұрын
Not sure the exact top speed but it might be like 2 maybe 3 MPH.
@aiizen_pr
2 жыл бұрын
@@ReadytoRunRC ok thank you
@JoeOvercoat
2 жыл бұрын
The worm drive of the SCX24 is ideal for slow speed, where it acts as a mechanical drag brake. So if it’s low speed you are looking for, a tiny truck with a worm drive is ideal.
@texomarc
2 жыл бұрын
The servo should be the emax digital servo, just rebranded for Injora (my guess). The emax digital servo is typically a couple dollars more than the analogue.
@ReadytoRunRC
2 жыл бұрын
I was comparing them when I took the emax off and it looked very similar and had the same thoughts as you that it was just a rebranded emax. Everything looked identical except the sticker.
@texomarc
2 жыл бұрын
@@ReadytoRunRC Yeah, Emax has two versions, one digital and the other analogue. The one that everybody puts in their car is usually the analogue. The digital is claimed to be a little better. The injora servo should be the digital version of the emax.
@Missed3rd
5 ай бұрын
I ordered the same servo and waited all week for it and the first day she broke aha, must have been just a lemon
@mpampis_o_fou2027
Жыл бұрын
i put this motor and it screams,i'm repositioning pinion and gear 3 times and it continues,i did something wrong?
@ReadytoRunRC
Жыл бұрын
Not sure what’s wrong. If it’s not the mesh then I can’t think of an answer to your problem.
@forevercampeon
Жыл бұрын
What’s the top speed of the motor?
@ReadytoRunRC
Жыл бұрын
Probably like 2-3mph
@RCYT_
2 жыл бұрын
Where do you buy all this sir?
@ReadytoRunRC
2 жыл бұрын
In the links in the description
@JollyPirateAhoy
2 жыл бұрын
Do you have to add grease to the motor gearing?
@ReadytoRunRC
2 жыл бұрын
No you don’t need to.
@JollyPirateAhoy
2 жыл бұрын
@@ReadytoRunRC thank you for the answer. I'm doing my jeep scx24 and it's my 1st time doing all this. So thank you for the videos.
@ReadytoRunRC
2 жыл бұрын
@@JollyPirateAhoy you’re welcome. Have fun with your build. Glad my videos are helping you out.
@dawsonbrooks5071
2 жыл бұрын
can the 66t push more weight then the 50t ?
@ReadytoRunRC
2 жыл бұрын
The 16 extra turns should give it more torque to handle the extra weight. I never tested it against the 50t but in theory yes it should.
@dennisdespots8578
2 жыл бұрын
Why don't you mention that you have to cut off motor side battery tray Mount
@ReadytoRunRC
2 жыл бұрын
I didn’t even think of it because I already had to do that when I put the barrage motor in and I mentioned that in that video.
@dirtrider88
2 жыл бұрын
damn, all those links in the description but not one for the axles
@ReadytoRunRC
2 жыл бұрын
Oh I didn’t realize that. I have to get the link from my axle video and paste it in the description.
@ReadytoRunRC
2 жыл бұрын
I updated the description. Thanks for pointing that out.
@dirtrider88
2 жыл бұрын
@@ReadytoRunRC awesome now wheres that "to be continued" video? haha Edit: i still dont see it there
@ReadytoRunRC
2 жыл бұрын
@@dirtrider88 it’s my dam climb third try video.
@ReadytoRunRC
2 жыл бұрын
@@dirtrider88 I just saved the links again in the description. Now try. They must not have saved last time.
@richiebricker
2 жыл бұрын
Lets o the dam
@ReadytoRunRC
2 жыл бұрын
Dam climbing coming right up! Waiting on favorable weather.
@thecruz55
2 жыл бұрын
Please count me in all giveways
@ReadytoRunRC
2 жыл бұрын
Ok but to enter you have to comment on the giveaway videos. The random comment picker picks comments out of those videos. You can’t just say count me in all of them. The comment picker doesn’t know that.
Пікірлер: 71