私は元インクジェット技術の開発者でした。このような動画を作成していただくのはとても素晴らしいことだと思います。 ただ、残念ながらこのビデオにはいくつか根本的に間違った説明がありましたのでご指摘させていただきます。 (1'50") 「このヒーターは1マイクロ秒間に約100度も温度が上がる…」とありますがこの程度の昇温速度では正しくインクは飛びません。実際にはもっと急激な発熱が必要であり、実際のプリンターでは1マイクロ秒間に数100度以上の速度で昇温します。(パルス幅は1マイクロ秒程度です。) (2'50") 「しばらくしてヒーターがOFFになると蒸気が凝縮して泡が潰れます」は現象として間違っています。実際には、発泡した瞬間にインクはヒーターから離れるため、ヒーターはOFFにならなくてもすぐに気化は止まります。発泡した瞬間には約100気圧もの爆発力が発生するためにその勢いでインクは運動し、泡はインクの慣性で引き延ばされます。そのため引き延ばされて膨らんだ泡の中はほぼ真空です。真空の泡なのでいずれ大気圧に押しつぶされ、膨張が止まり、泡は消えます。これが正しいThermal inkjetの原理です。 (3'45") ヘッドを左右に動かすモーターとしてはstepping motorは使いません。リニアエンコーダーを用いたDC servo motorを使います。さらに、リニアエンコーダーを読み取りながら、インク滴の吐出タイミング信号を出すことにより、ヘッドの移動速度が変化してもいつも正しい位置にインク滴を落とすように制御されています。紙送りモーターもロータリーエンコーダーを用いたDC servo motorが使われています。 (6'40") 動画では黒いパネルの上に赤と緑の光を照らしていますが、これは実験としては誤りです。正しくはパネルは白でなくてはならず、部屋を真っ暗にして、そのパネルに赤と緑の光を当てなくてはこの動画のようにはなりません。光の当たっていない部分が黒いのは部屋が暗いので黒く見えるからです。 (10'30") 減法混色でCMYを混ぜ合わせる時にインクどうしを必ずしも同じ位置に重ねることは必須ではありません。色どうしが位置がずれてお互いに重ならなくても遠くから離れてみると混じったのと同じ色として見えます(並置混色と呼ばれます)。したがって、淡い緑色を作るために正確にシアンとイエローのドットを重ね合わせた緑のドットを作って並べる必要はなく、シアンのドットとイエローのドットを適切な密度でそれぞれランダムに並べて重ねれば淡い緑に見えるので、そのようにプリントされています。(実際にプリントされた画像を拡大して見ればわかります) (12'15") Kインクを使う理由の解説が適切ではありません。黒やグレーなどのように彩度の低い色をCMYの重ね合わせだけで表すことはできますが、特に黒に近い濃いくすんだ色を表現するためにはCMYのたくさんのインクを使わなければなりません。使うインクの総量を抑えるためにCMYのそれぞれのインク量の内、共通のインク量の部分をKインクに置き換えることで総インク量を抑えることができます。これをUCR(Under Color Removal)と言います。また別の理由もあります。文字は黒が多用されますが、CMYで黒文字をプリントしようとした時、CMYのドットの位置が少しでもずれると色が滲んだ黒文字となりとても見にくいので、文字はKインクだけでプリントするのが望ましいのです。 以上です。 I was a engineer of inkjet technology. I think it is great work that you have created such a video. However, unfortunately, I would like to point out some incorrect explanations in this video. (1'50") It is explained that "This heater raises the temperature by about 100 degrees per microsecond...", but ink does not eject correctly at such rate of temperature rise. In reality, more rapid heating is required, and in actual printers, the temperature rises at a rate of several hundred degrees or more per microsecond. (The pulse width is around 1 microsecond.) (2'50") "After a while, when the heater is turned off, the vapor condenses and the bubble collapses" is wrong as a phenomenon. In fact, at the moment of bubble generation, the ink leaves form surface of the heater, so vaporization stops immediately even if the heater is not turned off. At the moment of bubble generation, the explosive pressure reaches up to 100 atmospheres, so the ink is moved by the momentum, and the bubble is expanded by the inertia of the ink. Therefore, the inside of the expanded bubble is almost a vacuum. Since the bubble is a vacuum, it will be pressed by atmospheric pressure, the expansion will stop, and the bubble will be collapsed. This is the correct principle of thermal inkjet. (3'45") The stepping motor is not used as a motor to move the head left and right. A DC servo motor with a linear encoder is actually used. Furthermore, by reading the linear encoder and sending out an ink drop ejection timing signal, the head is controlled to always eject ink droplets at the correct position, even if the head movement speed changes. The paper feed motor also uses a DC servo motor with a rotary encoder. (6'40") The video shows red and green lights on a black panel, which is incorrect for the experiment. If the panels were black, as shown in this video, we would hardly be able to see anything even if we shine light on them. So the panel must be white, and the room must be dark, and the red and green spotlight must be shined on the panel in order to make it look like in this video. (The areas that are not illuminated should appear black because the room is dark.) (10'30") When mixing CMY in subtractive color mixing, it is not necessary to put the inks on the same position. Even if the colors are not in the same position and do not overlap each other, from a distance they appear to be the same color as if they were mixed together (called spacial color mixing). Therefore, it is not necessary to create and arrange cyan and yellow dots precisely in order to create a pale green color, but rather, if cyan dots and yellow dots are arranged and overlapped randomly at the appropriate density, the color will appear pale green, and the image is printed as such. (You can see this by zooming in on the actual printed image) (12'15") This is not an adequate explanation of why K ink is used. While colors with low saturation, such as black and gray, can be also represented using only CMY superpositions, especially dark dull colors close to black, you have to use a lot of CMY inks. In order to reduce the total amount of ink used, the common ink portion of each CMY ink quantity can be replaced with K ink to reduce the total amount of ink. This is called UCR (Under Color Removal). There is another reason. Black is often used for letters, but if the CMY dots are misaligned even slightly when printing black letters, the black letters will be blurred and not beautiful, so it is preferable to print letters using only K ink. That is all.
Пікірлер: 220