The tip about the baking soda is amazing!!! Just got one done and got the stickiness right off!
@deancurtis995
3 жыл бұрын
Great tutorial 👌🏻😎
@pingusx34
Жыл бұрын
Hola, Gran video, las resistencias habría que cambiarlas? Un saludo desde España.
@xsm5525
2 жыл бұрын
the 4 color FX on my DJM 800 are not lighting up, (bought it like this) do you suspect it's all 4 LEDs that are knackered?
@MaxELECTRONICS
2 жыл бұрын
Sounds like could be transistors that drive the leds, check them first, it’s unlikely that all 4 leds failed at the same time
@roy5110
10 ай бұрын
Hello Max, thank you very much for this video. With the help of this video I was able to do the same thing on my CDJs for the Cue and Play buttons and it looks great. I would like to do more and put LEDs to light up the JOG like the CDJ 2000 or other turntables. Do you have any tutorial or advice? I thank you in advance
@MaxELECTRONICS
10 ай бұрын
It’s same process goes for any equipment, just desolder old led and put new one in. You may encounter SMD leds, they’re same leds just soldered on the surface of pcb instead of through hole, you can buy them too and replace them.
@roy5110
10 ай бұрын
@@MaxELECTRONICS Thank you for your answer. I may have expressed myself badly. I use Google translator 😁. On the CDJ 1000mk3 there are no LEDs on the jogs. how can we put? THANKS
@MaxELECTRONICS
10 ай бұрын
@roy5110 you can take jog off and in the cavity of the enclosure (where jog sits) run a 3mm led strip around the perimeter and connect it to CDJ’s power supply (12v), then reinstall the jog and this should do the trick, I’ve done that with turntables
@roy5110
10 ай бұрын
@@MaxELECTRONICS Ok, thank you, I'll try that. good continuation. 😇
@massattack3816
9 ай бұрын
where do you buy your leds from blue ones and multi colour leds ones?
@MaxELECTRONICS
9 ай бұрын
Use to on eBay but AliExpress is cheaper, simply search for 5mm blue led, or 5mm colour changing led slow.
@sonnyxet
3 жыл бұрын
Hello, excellent tutorial, I have a problem with the leds of my 1000 mk3, they do not light, I have never modified anything. Everything turns on and works fine, except the leds. Do you know the reason?
@MaxELECTRONICS
3 жыл бұрын
It’s hard to say without looking, see if there’s power on the rails before the transistors that trigger led, check that all cables are plugged in firmly, check transistors, check the ic. And continuity from ic to the transistors.
@paulfrey8450
Ай бұрын
Hello, how bright should the leds be?
@lcaise
Жыл бұрын
Does a trick with Soda work with Reloop 6000 stickiness shit on the plastic case ??
@MaxELECTRONICS
Жыл бұрын
Yes, works with any old plastics that deteriorated and became sticky.
@lcaise
Жыл бұрын
@@MaxELECTRONICS Wow needs to try, it is terrible at the moment!
@deancurtis995
3 жыл бұрын
I’ve remove the leds and replaced them but now the cue button doesn’t light up any ideas ??
@MaxELECTRONICS
3 жыл бұрын
Check that you’ve soldered them in correct polarity
Пікірлер: 21