After 2 weeks of searching, your video is the only one that is clear, instructions easy to follow and the helpful tips were a lifesaver! Thank you so much❤
@chazshanks
2 жыл бұрын
Excellent video, really helped me when i did the pump replacement on my RR this weekend.
@jesseruiz2337
3 жыл бұрын
Just purchased the water pump kit for my 2013 Range Rover sport. I ordered it on Sunday 3/7/21 !and received it 2 days later.
@ivicarenatomic5465
3 жыл бұрын
Nice and through explanation, thank you.
@MrOxforddesign
5 жыл бұрын
Threads are a bit confusing in the description but otherwise excellent video. Might be worth clarifying.
@tjwrongwaymead8374
2 жыл бұрын
Great video. Doing that without the supercharger removed is a trick. And all fine and dandy till I broke a waterpump bolt. Lower one on driver's side actually protrudes into open antifreeze causes it to seize . 2 weeks of careful Dremmel grinding and I was able to Heli-coil it. Nightmare
@miguelrueda4975
3 жыл бұрын
Doesn't show the fan clutch removal
@ChezDoesCars
5 күн бұрын
Do you think the coolant y-pipe can be replaced by just removing the water pump and keeping the supercharger on? Thank you.
@Chewie374
3 ай бұрын
On the by pass. You do a quarter turn clock wise?
@alhosni1027
4 жыл бұрын
Well done keep going mate
@asid731
2 жыл бұрын
Torque specs for water pump????
@tjwrongwaymead8374
2 жыл бұрын
I have a technical question. There's an actuator with 2 vacuum nipples bolted to the back of the supercharger. It has an electric pigtail plugged in . But vacuum no lines running to it. What is this and can I leave it ? It will be buried when I install the supercharger
@dudeman8323
3 жыл бұрын
Clarification is needed on the difference between "counter clock wise" and "anti clock wise" are they not the same? About 1:45 they are mentioned regarding the fan...
Nice video, personally I've done more broken y pipes under the supercharger than water pumps, most failures I see are well over 120 thousand miles . Very durable when you think about it.
@schmick63
Жыл бұрын
Not sure about the V8, but I had the Y pipe crack on my 2017 3.0S Velar P380 at 32,000 kms. Luckily for me it was still in warranty so the dealer handled it. I've now just had a leak start from the thermostat housing at 52,000 kms. Oh the joys. Plastic fantastic
@bradmajor92
3 жыл бұрын
Is this the same procedure for the 3.0 sdv6 RRS 2014?
@chasingwaves11
2 жыл бұрын
My question is what is the right Torque for those tiny screws on the water pump .. I get all kinds of different answers lol 🤦🏽♂️ 2011 Rover sport HSE v8 5.0 none supercharged. I can’t stand the fact that rover put all kinds of plastic parts on this motor 🤦🏽♂️ it’s a amazing machine! But way couldn’t they have used aluminum tubes with a flange and o-rings. Would it really have cost them that much more money this is a 90k machine !!! 🤦🏽♂️
@ramonmartinez915
7 ай бұрын
Gracias buen trabajo
@Justme-tx2ux
4 жыл бұрын
Thanx 4 the video Do I have to replace mine to avoid high temp which causes engine issue in the future ?
@atlanticbritishrp
4 жыл бұрын
Are you currently experiencing issues with your water pump?
@adamfritz4503
2 жыл бұрын
Why has no one asked about the torque specs for the T30 water pump bolts? Seems important.....I would hate to snap one of those off. The video mentions torque but does not say. Anyone know? I just got my old one out. Thank you for the video!!!!
@tjwrongwaymead8374
2 жыл бұрын
I did snap one off. Lower one on driver's side goes into open antifreeze. Gummed it all up. Had to Dremmel it out. Then helicoil cuz it was impossible to not get into the aluminum. I went 18 footpounds and that felt tight
@mikehoncho3695
Жыл бұрын
Its a German car the specs are goodntight.
@sargentseabass
Жыл бұрын
All this information and can't seem to mention the torque spec?
@JoseA817
3 жыл бұрын
Do u have a video on how yo replace the 2006 model and on how to bleed the system
@davidevans8408
6 ай бұрын
Its normall thread on the fan TURN LEFT TO UNDO/REMOVE
@polayer4040
Жыл бұрын
Does anyone know the part number of the hose with the plastic elbow that goes into the water pump ? Thank you in advance
@LynxStarAuto
8 ай бұрын
It's part of the upper turdmostat hose #LR049990 You should also replace throttle body pre-heater hose #LR045239
@big-lv2wt
5 жыл бұрын
Hi there I have a 2012 Jaguar XF same water pump deal 5.0 engine but for some reason is still leaking antifreeze around that area can you help me out?
@atlanticbritishrp
5 жыл бұрын
Hi! We would really recommend you seeing your Jaguar mechanic to diagnose the issue, but with the 5.0 engine there are several spots that can leak including the gaskets around the water pump along with the o-rings and seams at the Y-pipe that extends out from the water pump.
@SebastianBlix
2 жыл бұрын
To clarify the fan coupling thread release directions: Supercharged = counterclockwise (lefty loosey righty righty) NA = clockwise (righty loosey lefty righty)
@jesseruiz2337
3 жыл бұрын
On a 2013 range rover sport supercharged, when standing in front of the engine bay when taking of the fan, do u turn the nut bolt with the wrench clockwise or counter clockwise? I've been trying counter clockwise but it dont budge. Your help would be appreciated.
@LynxStarAuto
8 ай бұрын
All of them loosen in the opposite direction of rotation. The catch is, where is the pulley in relation to crankshaft rotation. Some are off to the left, others to the right, which can change the thread on the pulley.
@danikfir4309
4 жыл бұрын
Hey can I put back the sleeve on the elbo? My elbo broke and I had to remove everything completely. The sleeve was damage and elbo. Do I need to replace the complete water pump or can I make something work?
@roverparts8796
4 жыл бұрын
Our tech, Gareth says: "If he broke the black sleeve in the water pump , he’s going to need a new water pump assembly. If he broke just the elbow, he’s going to need a new hose assembly. If that is the case, we'd need his VIN number to tell him which hose assembly, as that hose assembly was changed and updated after a certain VIN."
@ottisdixgud3527
6 күн бұрын
You might want to turn that belt around the right way. 😅
@r8228c
4 жыл бұрын
For the small elbow on the front of the waterpump, how do you remove it? The video mentioned to put pressure on the plastice sleeve. How do you put pressure on it, with what tool?
@atlanticbritishrp
4 жыл бұрын
You can put straight pressure on it with the flat side of a flat-head screwdriver or something that will give you leverage without damaging the sleeve while you pull the elbow off.
@approx01
4 жыл бұрын
im doing this job right now and i couldnt find any good info about how to push it either. you push the collar back against the water pump. the collar stays in the pump and the plastic elbow slides all the way out. imagine one of those plastic snap rivets but you can pull the center part all the way out.
@superchile9640
4 жыл бұрын
Did the plastic y pipe under the intake manifold have any sign of leak? Hope you changed that out as the customer will be back...
@LynxStarAuto
8 ай бұрын
It's a LRJ. The customer will always be back. They have their own VIP lounge in my shop.
@desertcamel3573
4 жыл бұрын
How to remove and installed secondary belts ? video-
@doctortammymayo3997
4 жыл бұрын
Hi. I have a call at lake on my 2014 Range Rover sport. The coolant splash pattern is under the air intake, at the side of the oil filter and under the oil filter. I don’t feel any wetness under the front plastic crossover tubing. I don’t see any wetness around the back plastic crossover tubing ( the tubing behind the manifold). I watch this video and was thinking possibly it was the water pump. Does this splash pattern sound like water pump damage?
@doctortammymayo3997
4 жыл бұрын
There’s also a lot of our food under the water pump on the front of the engine
@doctortammymayo3997
4 жыл бұрын
I apologize for dictating. There’s a lot of antifreeze on the front of the engine under the water pump
@atlanticbritishrp
4 жыл бұрын
@@doctortammymayo3997 Possibly... have you checked the related coolant hoses?
@doctortammymayo3997
4 жыл бұрын
Atlantic British I will look. Thanks
@doctortammymayo3997
4 жыл бұрын
Hello again. I have removed the air intake Plenum and I see The antifreeze all around as I said before. I don’t see any wetness on the tubes. can I start the engine without the air intake planum on just for a few seconds to see if I can see where the antifreeze is leaking?
@ericjay7763
3 жыл бұрын
Good evening! Hope your day was great I wanted to know what is the torque specs for 2011 Jaguar Xjl V8 for intake manifold. Thank you for your time & concern
@atlanticbritishrp
3 жыл бұрын
Sorry, we're Rover guys... You may want to check with Moss/XKs Unlimited...
@ericjay7763
3 жыл бұрын
@@atlanticbritishrp Thanks appreciate you n Xmas to u n ur family
@jeffreywilliams506
2 жыл бұрын
Did you put that drive belt on inside out ?
@markannichine
4 жыл бұрын
How do you get the tensioner into proper position with the belt on it?
@chasingwaves11
2 жыл бұрын
It only goes one way two notches on the back side that fall into a grove .. if your a DIY person it’s always best to take a picture of everything before diss assembly. Or draw it on paper 📝 ..
@markannichine
2 жыл бұрын
@@chasingwaves11 Thank you for replying. My problem was that I was not applying enough torque. Once I added an extension to my wrench, that solved it instantly.
@wallyyfm
5 жыл бұрын
How much is this job completely done with parts and labor?
@atlanticbritishrp
5 жыл бұрын
100%
@REEVES636
5 жыл бұрын
That would all depend on where you get the parts from and who does the job. It's not a hard DIY job if you are comfortable with working on your Rover.
@atlanticbritishrp
5 жыл бұрын
Here's the waterpumps... they are on sale at the momment: genuine: www.roverparts.com/Parts/LR097165GK | aftermarket: www.roverparts.com/Parts/LR033993K. General rule of thumb with Rover waterpumps... If you are looking to hold on to the vehicle for a while, you'll want to spend the extra for a genuine or OEM waterpump. If you aren't holding on to the vehicle for long, lesser aftermarket pumps are OK, but they usually don't last very long.
@georgesolomon5696
5 жыл бұрын
how long should the OE version last?
@roverparts8796
4 жыл бұрын
Genuine will last longer than aftermarket typically, but like anything, depends on how hard the vehicle is driven, enviroment, etc. The OE version is now no longer available... guessing LR caught wind of it and told the OE manufacturer to drop it. The genuine and aftermarket options we carry are here: www.roverparts.com/nxt/?Dropdowndescription=LR4+%2F+Discovery+4&Category=ENGINE&Subcategory=Cooling%2FHeating
@derekkchung
Жыл бұрын
counter clockwise vs anti clockwise.....😵💫
@Chewie374
3 ай бұрын
And clock wise for the by pass. I think
@carana2002
Жыл бұрын
Good job...Just be careful if You buy something from these guys from Atlantic British, I bought a pair of authentic DELPHI shock absorbers for my LR, and I received an unbranded Chinese made shock absorbers.....Like I said BE CAREFUL with these guys...
@LynxStarAuto
8 ай бұрын
Lmao. These cars are absolute junk, but my god do they pay the bills!
Пікірлер: 68