Anyone else waiting to see if them Duke boys make it over that pond after the commentary? Love it!!!
@brandoncantrell3317
4 жыл бұрын
Them boys sure are in a pickle again
@Angkinkaid
3 жыл бұрын
Oman, I am crying!!!
@irishlad8797
2 жыл бұрын
YeeeeHaaaà😎
@centaur188
4 жыл бұрын
You should never run wires over the top of the engine, oil, heat, water etc! apart from having to disconnect them again for any engine maintenance , always channel them up the wings, and around the body panels.
@goldfishninja8086
4 жыл бұрын
Centaur1 it was obviously just a temporary placement for the video you idiot.
@2009jamrock
2 жыл бұрын
@@tofinoguy agreed.. and i guarantee those wires will be fried before the next oil change.. i would at least routed them to make it look oem.. added wire loom... and made the wires hidden.. for a clean look
@williamfortson4495
4 жыл бұрын
The wiring lol
@rodsykes6947
4 жыл бұрын
I used a cheap Haigh siphon pump on my 2008 Forester (similar set up to the WRX) to drain the upper radiator chamber and then the upper hose after disconnecting the hose at the radiator end. Minimal leakage when disconnecting lower end of hose and easily absorbed by a small towel. Much easier and quicker than removing engine bay undercover and draining via the radiator plug. Pulled a little over a litre (quart) of coolant and replaced after install of adapter.
@Arizona_rider
3 жыл бұрын
Oh, really??? I forgot that part. Lost 3 gallons. I thought it was going to be a trickle. Nope then i had to read the instructions because I was stumped on a part. I was changing the oil at the same time. Once i got done it was worth it
@AlienMonkeyDXB
5 жыл бұрын
So... We're working on the UPPER hose, basically one of the HIGHEST POINTS in the system yet you say we MUST drain ALL the coolant... Explain please!
@aircoolednation423
5 жыл бұрын
i think it isnt needed. just remove the hose and if coolant falls out, then drain the system
@willk3807
4 жыл бұрын
It's safe practice to flush your coolant system once per year anyway. Or I could have said...stop being an asshole
@originalgameronline3457
4 жыл бұрын
Lol, I know right. What is this guy doing?? Creating a shit ton more work for nothing.
@willthecardude6900
4 жыл бұрын
They just mean let some coolant out from the bottom of the radiator so that the coolant doesn't spill everywhere.
@SOLDOZER
4 жыл бұрын
The video is correct. Drain all coolant and then refill with Glowshift Green Koolant.
@genso3065
5 жыл бұрын
I got a glowshift water temp gauge . Can't wait to install it on my turbo Baja. Thanks for the installation vid.
@healmeat
2 жыл бұрын
I want this dude to narrate my life.
@yyabay
2 жыл бұрын
Rip Wiring and the hose clamps... What a mass for a briliant looking engine..
@Kastro876
4 жыл бұрын
Simple install... Only thing I need is those connectors and a tester
@jogmas12
4 жыл бұрын
This is the video I was looking for!!!!!! Probably the best video I’ve seen on youtube so far for installing not only glowshift but any aftermarket temp gauge.
@GlowShift
4 жыл бұрын
Thank you!
@Grumpy412
2 жыл бұрын
Finally, someone pouring liquid out of a can the right way!
@someguyontheinternet-
5 ай бұрын
I have found that it's better to cut off a couple of inches off of the radiator hose after cutting it in half, before assembling everything back together. Some of those hoses are in tightly confined spaces and adding length to the hose may throw other things off or cause a kink in the hose in first bend following the splice.
@jamesryan1939
8 ай бұрын
Wouldn't you want the reading after the thermostat? This would be reading the temperature of the coolant directly after it ran through the radiator, not really representing what the engine temp is.
@import-chileracingandperfo7322
5 жыл бұрын
when you connect the gauge to the fuse box and use an extension to fit in the fuse space, as you do when you have more gauges and everything needs to be connected in the same way, I mean its light and ignition
@hiccupfpv5757
4 жыл бұрын
So... why do I need to connect it to 3 different power sources 😳 I feel dumb for asking that but shouldn’t I be just fine wiring it into just a normal 12v on ignition and be fine?
@GlowShift
4 жыл бұрын
The constant 12 volt power connection allows the gauge to remember the color that you set so you do not have to reset it every time the car turns on. The ignition 12 volt turns the gauge on. And the 3rd connection is to enable the gauge to dim when the headlights are turning on.
@DL-qq4nu
3 жыл бұрын
@@GlowShift Thank you for explaining this. I was dumbfounded. but a serious question is why tho? No one cares about the colors we just want a functioning gauge and no one wants a auto diming gauge either that. So in my case where i just want it to turn on when key is turned the one position i simply just ignore the addition 2 wires?
@xXWILDBILLXx69
Ай бұрын
Too bad you don't have a pod for my car... I seriously need one!
@AlienMonkeyDXB
5 жыл бұрын
How about removing a section of the hose as to compensate for the added length of the adapter and keeping to the OEM length of the hose?
@GlowShift
5 жыл бұрын
Sure, you can do that.
@UndisputedMRecabo
3 жыл бұрын
@@shaw-man2253 I was curious if there was a reason in this particular application, I'm about to do the same install, except on a Fox 5.0 Mustang and if I didnt remove the amount of hose I'd be replacing with the adapter, my hoses wouldn't be close to stock orientation! I'm surprised that the hose was still oriented properly in the vid!
@CoolDansta
11 ай бұрын
Awesome wire manager 😂
@larryeaton7384
4 жыл бұрын
It is my understanding that any inline coolant temperature gauge should be installed before the thermostat. You installed yours on the after thermostat upper radiator hose. Why would you choose this inline section?
@GlowShift
4 жыл бұрын
It depends on which temperature you want to monitor.
@Steve63115
3 жыл бұрын
I don't think this is good at all! This is ONLY checking the water basically at the radiator NOT in the engine. You really need to know what's going on in the engine. REMEMBER! The water temperature is suppose to be maintained in the engine, that's why the engine requires a THERMOSTAT. The above device beyond the thermostat is only checking outside the engine NOT in the engine... Big mistake... Please feel free to correct if am wrong. Bottom line, the water temp after the thermostat while closed will be very different from the water before the thermostat...
@motorolasafi
2 жыл бұрын
@@Steve63115 I was also thinking the same, but once when the T valve opens hot coolant is going to flow through this pipe and guage will show the engine temperature?
@EkonRekon
2 жыл бұрын
@@Steve63115 The thermostat side is the hot side. Even if the thermostat is off, the engine temp inside the engine will transfer that heat past a closed thermostat.
@goldfishninja8086
5 жыл бұрын
I’ll be placing my order now
@GK5_
3 жыл бұрын
If this is installed at the uppermost part of the radiator, gravity pulls the fluid downward so why would you have to drain all the fluid if you're cutting the hose at the top?
@GlowShift
3 жыл бұрын
It's recommended as a safety precaution.
@paulwilliams6927
Жыл бұрын
@@GlowShift do you drain the fuel tank too as a safety precaution?
@connorsmith4646
11 ай бұрын
@@GlowShift remove the engine for safety precaution
@minimanadam
5 жыл бұрын
Great walk through
@zackmorgan4500
6 ай бұрын
Put the Teflon tape on backward
@fernandovera7230
3 жыл бұрын
Un profesional como la copa de un pino, gran video
@leiladaquil6587
2 жыл бұрын
The wires should be insertef to black flexible conduit to look well managed harness.
@bicdut
3 жыл бұрын
Replace those original hose clamps.
@MegaDevify
3 жыл бұрын
So, since you tapped into the fuses like that, how do you install other gauges as well? It looks like they’re you can only use a fuse for one gauge, and what if you run out of fuses?
@GlowShift
3 жыл бұрын
You can wire all the gauges to the same circuits. You just need to put all the red wires together, all the yellow wires together, all the orange wires together, and all the black wires together. You can purchase a multi-gauge wiring kit from our website which will make wiring the gauges easier.
@Data4664
5 жыл бұрын
THNXS!
@kvquackmachine
4 жыл бұрын
Hi, may I know what kind of additional wire you are using? Any specific type of wires or just a simple 10amp wire would do?
@GlowShift
4 жыл бұрын
Standard 10amp wire is fine.
@kvquackmachine
4 жыл бұрын
@@GlowShift Thank you.
@pauljasondimasaca2462
4 жыл бұрын
questions.... so i pretty much watch your videos all over ...ive decided to order boost gauge water temp gauge and volt gauge... my question is ... do i need to find the constant 12 volts on each gauge? and each ignition fuse? and each head lights on fuse?
@pauljasondimasaca2462
4 жыл бұрын
what im trying to find out is if i install 3 gauges on 1 constant 12 volts fuse and 3 gauges on 1 ignition and 3 gauges on 1 headlights on switch fuse
@bballkid7409
3 жыл бұрын
@@pauljasondimasaca2462 did you figure that out? I am definitely not trying to wire each gauge to 3 individual fuses, that’s ridiculous lmao
@johnrussell8410
3 жыл бұрын
Interesting that the video did not mention cutting out a section of the radiator hose so that with the Water Sender Adaptor inserted, the hose length remained unchanged. Or did I miss something?
@GlowShift
3 жыл бұрын
Every application will be different. Some need to be trimmed and some don't.
@dawsonjames8946
3 жыл бұрын
What do you do when you guys don't sell the proper house size to fit a vehicle. I bought it and now I don't have and can't find out where to put it anywhere else because I have no adapter
@WexfordGamingNetwork
3 жыл бұрын
Im aware all the wiring is necessary , but this is all for one gauge. Whats the best way to keep wiring clean if i were to lets say put in 3 gauges? Can i just splice multiple gauges wires into one fuse piggyback connector?
@GlowShift
3 жыл бұрын
We have a 3 gauge wiring kit where you connect all of the gauges down to one single wire.
@anagutierrez7218
4 жыл бұрын
Ok so I have an issue, water temperature gauge should read around 180 when radiator fan comes on, when the fan turns on it gradually goes down in reading anywhere form 155-160 degrees. Fans go off and then reads around 180 again. Faulty sending unit?
@Steve63115
3 жыл бұрын
I don't think this is good at all! This is ONLY checking the water basically at the radiator NOT in the engine. You really need to know what's going on in the engine. REMEMBER! The water temperature is suppose to be maintained in the engine, that's why the engine requires a THERMOSTAT. The above device beyond the thermostat is only checking outside the engine NOT in the engine... Big mistake... Please feel free to correct if am wrong. Bottom line, the water temp after the thermostat while closed will be very different from the water before the thermostat... Basically your only reading the temperature around the radiator/fans... (Not in the engine)...
@bluebird5974
Жыл бұрын
What's is ideal temperature..my cheverlate spark get 120 C then fan start...
@pickelrick6377
Жыл бұрын
So what if I want to install 3 gauges? Should I just splice into all fuse jumpers that were installed?
@GlowShift
Жыл бұрын
We would recommend the 3 gauge wiring kit. Will make wiring all the gauges to the same power source much easier.
@AirshipRocket65
7 ай бұрын
Hey Glowshift, do I need the 38mm hose adapter for the same type of Subaru just the naturally aspirated version? I don’t know how big the hose is and I can’t figure it out
@bryan6687
Жыл бұрын
Do you really have to drain the whole cool fluid to do this install ?
@GlowShift
Жыл бұрын
No.
@kart-it-out5975
12 күн бұрын
Should you always use a water sender when doing an aftermarket gauge?
@GlowShift
8 күн бұрын
Yes, unless your vehicle has a specific port for the sensor to thread into.
@kart-it-out5975
8 күн бұрын
It has the port, but it's not the factory sensor. So therefore I would use the water sender???
@kart-it-out5975
8 күн бұрын
@GlowShift I have a port, but the new gauge came with its own sensor, and the sensor isn't factory. So I should just use the water sender then???
@GlowShift
Күн бұрын
You could remove the factory sensor and use the new sensor, however, this may cause a check engine light. If you want to keep the factory sensor then yes, we recommend a water sender adapter.
@mfn350
3 жыл бұрын
Any brand would be the same method right for water temp gauge.
@samsmh9644
3 жыл бұрын
3 fuse tap seriously
@ramshacks9493
6 ай бұрын
Does anyone know if I have to cut from the Hot side or the Cold side before I order one, mine is a 03 is300 2jzge I prefer a accurate reading
@MrAllaboutgirls
5 жыл бұрын
What size is the sender for this car?
@JohnA...
4 жыл бұрын
I have a question if you have a few moments. I installed a temp sender just about like you have here to an aftermarket gauge, that worked just fine, however, I went to add in a fan control unit and wired it to the same gauge and it didn't work properly. At lower temps it would read to be a similar temp, however once it got to around 70c it would begin to fluctuate. The control unit would read much lower temps (and seem to be incorrect) than the gauge. I'm not sure if you have to wire something like that in a specific order or with separate wires. The temp sender is single wire, and I have a ground run to the hose adapter (similar sender setup as you did here). The gauge only has power, ground, and sender wires. The control unit is a Dakota Digital fan control unit. Thank you for any help/advice you might have.
@LiamsGotThis
2 жыл бұрын
I know this is two years late, but I can help! The gauge is designed to be the only thing that connects to a gauge. If you add a second thing connected to the gauge, it actually changes the resistance that the original gauge sees by putting another circuit in parallel (refer parallel circuits in electronics). This might be more noticeable at some temperatures more than others due to the non-linear design of the gauge. If none of this made sense, you would rectify this by having one sensor per piece of equipment.
@justifiedFaith209
3 жыл бұрын
Can you put whatever sensor you want in the water Sender Hose Attachment, or do you guys supply that?
@GlowShift
3 жыл бұрын
The temperature sensor will come with the gauge.
@grindsoul
3 жыл бұрын
Hey Glowshift: My temp gauge jumps all over the place after I hammer the throttle. it goes back to normal eventually when I come to a stop, but it will bounce from 0 to 300 and back down to 0 in a few seconds and then settle at 160 until I start driving again.. is this trapped air in the system?
@GlowShift
3 жыл бұрын
Sounds like a loose connection somewhere. Double check you wiring and the sensor.
@jjmccloud
Жыл бұрын
Can't you just use the existing temp sensor
@GlowShift
Жыл бұрын
No. The gauge will only work with the GlowShift sensor.
@weepnwillo
5 жыл бұрын
What kind of tester are you using to test the fuses-thanks
@GlowShift
5 жыл бұрын
We use a basic test light.
@corydalton4803
10 ай бұрын
hey glowshift. i installed the gauge and everything works fine but it reads around 20 degrees lower than what my ecu is saying. i have the sensor tapped into the thermostat housing. any reason why its reading lower?
@GlowShift
10 ай бұрын
Difference in the sensor location.
@SCHockeyGuy83
2 жыл бұрын
What type of connectors are those and which crimping tool are you using for it I almost botched this up on my first go and had to get creative with needle nose pliers on these it worked but want to get the right tool for the job as I'm fixing to install another set.
@GlowShift
2 жыл бұрын
Hozan P-707
@SCHockeyGuy83
2 жыл бұрын
@@GlowShift Thank you for the reply was racking my brain trying to figure that out!
@drake.cooper001
4 жыл бұрын
Does the sending unit come with the sensor? Or is this a separate product?
@GlowShift
4 жыл бұрын
The sensor comes included with the gauge, not the adapter.
@akhir_s1484
4 жыл бұрын
If the wire is too short for the temperature, Can I cut it and extend it or not?
@GlowShift
4 жыл бұрын
We do not recommend cutting the wires directly on the sensor, but the wires that get connected to the sensor and run to the gauge can be extended.
@jdm68
3 жыл бұрын
Can I use 14awg wire as the extension wire?
@punisherofArizonaUtilty
3 жыл бұрын
I am looking to expand my gauges for my 2008 Ford crown Victoria police cruiser. Where can I find trim that will work
@itzbeanzzz
3 жыл бұрын
Look up your make and model gauge cluster I’m guessing they make a dashboard pod and a pillar pod
@theblack_6.033
3 жыл бұрын
My water gauge keeps reading 300, but I know that that's not the temperature, because I just started the truck.
@GlowShift
3 жыл бұрын
Double check all your wiring to the temperature sensor. When the gauge pins itself at 300 like that, it means the sensor is not connected properly.
@theblack_6.033
3 жыл бұрын
@@GlowShift I just disconnected all the other wires, and left the ground, and red wire connected. In the Gauge it still reads 300.
@GlowShift
3 жыл бұрын
The gauge is reading 300 because of the sensor wires, not the power wires. The sensor wires are the green one from the back of the gauge and the white and black ones on the the sensor itself.
@BateMasterJeff9887
2 жыл бұрын
Hey Glowshift. The only wiring i got with my kit are the ones that connect to the back of the gauge and are way too short. I didn’t get the long ones like in the video. I looked on your website and I don’t see the 18 gauge wiring anywhere. What do I do?
I have a boost and water temp gauge am I able to still wire both gauges using the expandable circuit?
@GlowShift
3 жыл бұрын
Yes. You can wire up to 4 gauges to a single expandable circuit.
@vinniemadrox
4 жыл бұрын
What gauge wire do you use for the sensor wire into the cabin? The wire that came with my guage (the harness) isn't anywhere near long enough to reach inside my car.
@GlowShift
4 жыл бұрын
We recommend 20 gauge automotive grade wire.
@Unaveragebean14
3 жыл бұрын
What is the name of those two extended wires (Green&black)? Do they have to have silver innings?
@GlowShift
3 жыл бұрын
The silver connectors come in the packaging with the gauge. The wires are just any 18 gauge automotive wire.
@dreamingcode
3 жыл бұрын
I have a 1969 Impala and my fuses don't look like that can I still use this product? How would i wire it?
@GlowShift
3 жыл бұрын
We offer a few different types of expandable circuits to fit different type fuses. Check them out to see if we have one that matches your vehicle...www.glowshiftdirect.com/expandable-circuits/
@jenny-masterchef
4 жыл бұрын
i have similair aftermarket brand but the needle doesnt move.im using a different 2 wire coolant sensor which are works fine but maybe not compatible with these gauges?
@GlowShift
4 жыл бұрын
No, it will not be compatible.
@jenny-masterchef
4 жыл бұрын
@@GlowShift yeah i know i ask my mechanic.probably different calibration and sensor resistant.
@LongboardManiac
4 жыл бұрын
I'm having an issue, I installed this and tried to go with the directions as close as possible but when I turn my car on the temp gauge just sits at 300° no matter what. Do you know what could be wrong?
@GlowShift
4 жыл бұрын
Double check the wires to the sensor to make sure they are all securely connected and not pinched. Make sure the plug are fully connected to the back of the gauge. When the gauge is pinned like that, it means there is no sensor connected.
@LongboardManiac
4 жыл бұрын
@@GlowShift It ended up being a bad ground! thanks for the help
@motorolasafi
2 жыл бұрын
Can we use the car own temperature sensor or can we connect this guage with the car guage?
@GlowShift
2 жыл бұрын
No, the gauge will only work with the GlowShift sensor.
@motorolasafi
2 жыл бұрын
@@GlowShift ahan
@teshikofurusato4541
4 жыл бұрын
This looks confusing idk if I should spend $200 on gauges.
@bobhowells9603
4 жыл бұрын
Teshiko Furusato it only looks like about $70 in parts for just the water gauge
@mohdkhuzaimie6457
5 жыл бұрын
How to Install vecumm mitir,,
@bobhowells9603
4 жыл бұрын
why do need to install 3 seperate fuse taps for one gauge?
@GlowShift
4 жыл бұрын
One is a constant power so the gauge remembers your settings, one for ignition so the gauge only turns on when the vehicle is turned on, and the 3rd one is optional to enable the dimming feature when the vehicle's headlights are turned on.
@DL-qq4nu
3 жыл бұрын
@@GlowShift Wouldnt this be 2 are optional?
@joeysweatshirt
3 жыл бұрын
Hey GlowShift i recently bought the 7 color water temp gauge, however i didn't realize my upper radiator hose is so short and i don't think i'll be able to use one of those hose adaptors, is there any other way to install it without the hose adaptor?
@GlowShift
3 жыл бұрын
What's the vehicle?
@joeysweatshirt
3 жыл бұрын
@@GlowShift 1991 240sx with RB20DET swap
@LiamsGotThis
2 жыл бұрын
I know this is a year old comment- but thought I'd chime in anyways. Usually there's a spot on the head of the engine where an existing coolant temp sensor, switch etc. can be removed and you can use a tee piece to install your new fitting with the correct adapters. Sometimes you can get thermostat housing extensions that have provisions for temp sensors. The way they did it in the video is actually extremely poor. What if the thermostat gets stuck shut? With the temp sensor in the upper radiator hose not receiving any water, the engine will overheat but because the thermostat is stuck shut and not sending water to the upper radiator hose, the gauge will show the engine to be cold which is extremely dangerous as you wouldn't know to shut off the engine.
@joacimlopez9735
Жыл бұрын
@@LiamsGotThis I experienced the opposite when the thermostat of my mustang stopped working. Upper rad hose expanded since coolant couldn't get past it(thermostat is located on lower rad hose before the radiator). My guess is that it would depend on where the thermostat is located on the vehicle.
@connorcook3123
Жыл бұрын
what amp fuses should i use on the the fuse taps
@GlowShift
Жыл бұрын
We always recommend 10amp or higher.
@saladasSTi
2 жыл бұрын
How do you make it remember the color?
@GlowShift
2 жыл бұрын
As long as the red wire from the gauge harness is connected to a constant 12 volt source, it will remember the color.
@raffyperez9624
4 жыл бұрын
where i could buy the parts of car where the guage was installed
@GlowShift
4 жыл бұрын
www.glowshiftdirect.com/
@jeffjames3141
5 жыл бұрын
Can I hookup a mechanical guage to this adapter?
@North49191
4 жыл бұрын
yes
@mdnaveed1781
5 жыл бұрын
Is it Available for superbikes
@GlowShift
5 жыл бұрын
You can put in on whatever you want as long as you're able to properly mount the sensor and have 12 volt power.
@timetotalk8275
3 жыл бұрын
Do you guys have a 2nd gen s10 video by chance
@GlowShift
3 жыл бұрын
Not at the moment we do not. Sorry.
@timetotalk8275
3 жыл бұрын
@@GlowShift no problem
@15hockeysim
4 жыл бұрын
What size additional wire is used?
@GlowShift
4 жыл бұрын
We recommend 18 gauge wire.
@JohnMarshton777
5 жыл бұрын
Hye Glowshift when I got my adapter it didnt come with a nut to enable wiring like that. The sensor just had a threaded part on top to attach eyelets to. Do you know anything about this, im having trouble wiring it up. In both your temp gauge videos, you have black and white wires just set into the adapter.
@GlowShift
5 жыл бұрын
Which adapter are you referring too? Is it a GlowShift product? All of our temperature sensors look like the one in this video so if it looks different, it may not be a GlowShift sensor.
@JohnMarshton777
5 жыл бұрын
@@GlowShift Hi, I can't remember if the sensor came with the hose adapter (which is glowshift) or the gauge (ebay) But I believe I got it to work not long after commenting haha, sorry about that.
@GlowShift
5 жыл бұрын
No problem. Glad you were able to get it figured out.
@bishop2355
2 жыл бұрын
At 4:12 what wire crimpers are those?
@GlowShift
2 жыл бұрын
Hozan P-707
@mrconlan7156
2 жыл бұрын
$$$$$ ? How much does this cost?
@GlowShift
2 жыл бұрын
www.glowshiftdirect.com/water-temperature-gauges/
@bvandme
5 жыл бұрын
If you are installing multiple gauges, say oil pres. and water temp can you combine the power wires into one that will connect to the expandable circuit ???
@GlowShift
5 жыл бұрын
Yes, we do sell a multiple gauge wiring kit that does just that depending on how many gauges you are installing.
@bvandme
5 жыл бұрын
I just bought the 3 gauge wiring harness for the old set of your gauges in hopes it would cure some problems but then we decided to buy a new oil pressure and water temp gauge, the tack is OK for now, these are from 2013 and Ive been told the new gauges have been updated with new sensors & wire ing, so will this wiring harness gs-gw3 work with these new gaugesThanks
@GlowShift
5 жыл бұрын
Yes, the gauge wiring harness is just wire so it will work with any gauges.
@cee5773
5 жыл бұрын
Will you get any codes for doing this?
@GlowShift
5 жыл бұрын
We did not experience any codes when installing this gauge.
@LOV2XRL8RL
5 жыл бұрын
Why would you get any?
@HaydenZ06
4 жыл бұрын
CesarTns bro what lol
@k-a147
3 жыл бұрын
No you won’t
@Steve63115
3 жыл бұрын
I don't think this is good at all! This is ONLY checking the water basically at the radiator NOT in the engine. You really need to know what's going on in the engine. REMEMBER! The water temperature is suppose to be maintained in the engine, that's why the engine requires a THERMOSTAT. The above device beyond the thermostat is only checking outside the engine NOT in the engine... Big mistake... Please feel free to correct if am wrong. Bottom line, the water temp after the thermostat while closed will be very different from the water before the thermostat...
@richardhbn3308
3 ай бұрын
this is checking the temperature of the coolant that has just come out of the engine, which is why they’re doing it on the upper hose.
@Aus.S7in
3 жыл бұрын
This entire time I thought it was a water pressure gauge. What’s the point of a water temp gauge besides more precise numbers? Just look at your stock temp gauge. It shows the engines temperature through coolant anyway.
@chevylvr902
3 жыл бұрын
Some cars are known for crappy gauges like OBS ford trucks. They’re notorious for reading wrong
@bluemarty8362
3 жыл бұрын
bc racecar
@jeremiahs4862
Жыл бұрын
Because some of us drive 90s shitboxes
@Riddle6EOS
5 жыл бұрын
Do you ship this product to Europe?
@GlowShift
5 жыл бұрын
Yes, we ship worldwide.
@bambambino23
4 жыл бұрын
Thats way 2 much work for a gague. Hook a ground, hood to battery, run wire to gavue....done.
@bluemarty8362
3 жыл бұрын
its for people who like to do things right not take shortcuts and jerry rig it
@PrimericanIdol
4 жыл бұрын
coolant... NOT water.
@GlowShift
4 жыл бұрын
It is referred to as both. Obviously we are monitoring the "coolant" temperature in the engine now but way back when, water was used in radiators before coolant was invented.
@PrimericanIdol
4 жыл бұрын
@@GlowShift We should get with the times. It's like referring to DIGITAL video recording as "filming", or calling a fridge an "ice box".
Пікірлер: 184