Good video. It's more like a 30-45 minute job when doing it the first time. Just to note, it's not needed to remove that carbon fibre trim below the head unit. You only need to move the front part of the centre console up slightly to remove gear gaitor. And like someone else mentioned, work the wires from top to bottom as it's a lot easier, threading from behind the glove box which saves you from removing that.
@tsunami770
Жыл бұрын
I just did it today. I took the lower side panel out and I was not very kind to the old module with a flat head and needle nose plier, after all, that is junk anyway. I used a wire guide from top to bottom and then hooked the wires with a wire hanger shaped into a hook right out where the new module was going to be. Quick and efficient. Only removed the side panel by the accelerator, I did not have to do all that (really took 20 minutes) and my CX-3 is just fine now. Oh and aside from the little sponge stickers I used a zip tie on the two cables so that gravity would pull them down together then I hooked them and pulled them out the hole for the new module. Oh and yes secured with zip ties and the anti-noise padding supplied.
@shaunalexander8956
2 жыл бұрын
When putting the cable in is easier to go top to bottom. Plus, test it all before putting all back together just in case it doesn’t work pain in the ass taking it all to part again.
@christianbarrasso4619
3 жыл бұрын
Love the work
@gohraa88
Жыл бұрын
very helpfull Video ,thx my Friend !!
@ADwaMoviesandMusicsproduction
Thank you very much, I have changed the radio by just watching your video 👏👏👏👏👏👏👏 for anyone still want to do it. The way I changed it for Mazda 2,scion IA 2016.
@CGRealStudios
I was able to achieve this on my Mazda 2 DJ (2017 model) routed the cables through the glove box and underneath the side panels, it was my first time doing it and it was difficult but I was able to get it working 😅
@jaydejaqaline6318
Hi this is a very useful and clear video. Would you be able to show how to connect an aftermarket reverse camera to the Mazda 2 2015 model. Would be greatly appreciated. Thanks
@Jess538
2 жыл бұрын
I just purchased the new Mazda console for my 2017 cx3 thinking I was capable, but this is horrifying!
@user-xx8qm2zo6y
Would love to get in touch with you. I have a 2017 toyota yaris IA that i need carplay in.
@JJZ6
2 жыл бұрын
how can I get car play on a scion iA 2016?
@xDaTrooper70x
Жыл бұрын
Thank you for the video guide. I was finally able to install apple carplay with no issues so far. Only thing is my touch screen is not working for some reason
@critter1171
Apple CarPlay keeps disconnecting itself, worked flawlessly for a year after installation. What do you think the issue is? Tried new cable
@Maririo93
14 күн бұрын
How do you get the vehicle telemetry transfer option?
@titan312
Жыл бұрын
Hi I was not able to unscrew the 10mm holding the screen, I used a drill screw, and by screw driver still doesn’t work. Do I need any stronger tools?
@morganix007
2 жыл бұрын
Hi! I own a 2016 Mazda 2 and I would like to upgrade by putting an aftermarket radio and speakers. Could that be possible??? Every autosound shop I have visited have told me that there are no aftermarket radio for it😕.
@boscokhoo2463
2 жыл бұрын
how can I upgrade my standard audio to OEM screen type on my Mazda skyactiv?
@analeighlerma1345
Жыл бұрын
Does this work for a Toyota Yaris? I know they have the same body and head unit as the Mazdas
@NINJA09XD
Жыл бұрын
Thank you for the video! Can you please send me the file to do the upgrade firmware?
Пікірлер: 219