Absolutely love it. Your videos are so detailed. Definitely inspires me to get to working on mine
@Brandon-LSX
2 жыл бұрын
Thanks glad it helped.
@evilokc
Жыл бұрын
I have a quick 9inch that I'm ready to install. Waiting on the third member to arrive then it's on.
@TanManFixes
9 ай бұрын
this helped a lot, thank you. on my 9 inch I accidently left the shoes attached to the backing plate lol. and I didnt have enough room to bolt on the plate. so I had to take out the screw and swing the brakes out of the way
@johnhogue9415
2 жыл бұрын
This video is very helpful I'm doing same swap currently What did you use for sway bar mounts? I got zero instructions or recommend parts from quick performance
@Brandon-LSX
2 жыл бұрын
When I was building the rear end I had them add sway bar mounts for 50 bucks extra. Otherwise you will have to weld on your own or get the clamp on kind.
@quentinc1275
2 жыл бұрын
Thank you for the in depth walk through. Is it possible to seat the bearings in the housing first then put the axle with the backing plate on afterwards so it I don’t have to take it to a shop?
@quentinc1275
2 жыл бұрын
I only ask because I haven’t received my axle yet just trying to get prepared
@Brandon-LSX
2 жыл бұрын
Thanks Not sure I would recommend that it needs some serious force to get a proper seat.
@jpmendoza138
3 жыл бұрын
How do you like that QP rear end? Any issues with the workmanship or quality.
@Brandon-LSX
3 жыл бұрын
Good quality rear-end. Fit and finish is spot on. Only thing I don't care much for is the torque arm bracket it's big and bulky and hits the body over hard bumps.
@InvincibleExtremes
Жыл бұрын
Great video, love it
@johnhogue9415
2 жыл бұрын
Great information on this swap We're your bearings pressed on when you received axle shaft's? I just received mine and now gotta remove brand new bearings
@Brandon-LSX
2 жыл бұрын
Mine did not come pressed on. If I remember right they were pretty snug though and semi pressed on and I used a 2x4 and hammer to knock lose.
@Macnificent78_
Жыл бұрын
What kind of Silicone?????
@chicagosfinestmoment4896
3 жыл бұрын
Car is looking great I have 3 of those 2 91z28 and a 92 rs I wish I had time to LS swap one of them
@Brandon-LSX
3 жыл бұрын
Thanks Man. Ya the LS swap definitely brought this car to another level.
@nathanielmaldonado4725
Жыл бұрын
Sell me one where are you located?
@timothymarsden2765
Жыл бұрын
If you are going to use sealant on the outer part of the seal use PERMATEX Anaerobic Gasket Maker
@bnrz28
Жыл бұрын
Great vid. How is the rear holding up? Any leaks or anything to lookout for ?
@treadandtracks
3 жыл бұрын
That new rear end looks great!
@Brandon-LSX
3 жыл бұрын
Thanks it does look good can't wait to test it out.
@rj_boostedz2897
2 жыл бұрын
Is that the fabricated big web housing? That’s what I ordered and just wanted to know if that’s what I’m getting. Thanks man
@Brandon-LSX
2 жыл бұрын
Yes that's the big web fabricated housing.
@rj_boostedz2897
2 жыл бұрын
@@Brandon-LSX awesome can’t wait for it to show up. Thanks man
@tylerbennett9044
2 жыл бұрын
I've got a qp 9 inch I haven't installed yet and I had it it machined to accept 98-02 brakes do I need to put the backing plates on before I press the bearings on?
@Brandon-LSX
2 жыл бұрын
Yes
@joshmoore7336
2 жыл бұрын
I was told by quick performance that I don't need the backing plates is that true that the bearing will hold them in
@Brandon-LSX
2 жыл бұрын
@@joshmoore7336 You need the backing plates to bolt the calipers to. Without the backing plates you won't have rear brakes or ebrakes.
@MasonsMotorworks
2 жыл бұрын
What’s the brass fitting there for? I just got mine and was curious!
@Brandon-LSX
2 жыл бұрын
It's a vent tube.
@MasonsMotorworks
2 жыл бұрын
@@Brandon-LSX no leaks coming out of it? Been a doing fine I’m assuming?
@Brandon-LSX
2 жыл бұрын
@@MasonsMotorworks No leaks but I did add a length of rubber hose connected to it. I'm assuming that's what the barbs are for on the fitting.
@MasonsMotorworks
2 жыл бұрын
@@Brandon-LSX one last thing, how’s the copper brake lines holding up? Still holding up well? Also where did you get the line flare tool?
@Brandon-LSX
2 жыл бұрын
@@MasonsMotorworks The copper Iines are holding up just fine. I did add small sections of rubber hoses and any contact points to keep them from rubbing through. Got the flare tool off Amazon.
@headported
2 жыл бұрын
where did you get thie 9" rear end from?
@Brandon-LSX
2 жыл бұрын
@Quickperformance
@headported
2 жыл бұрын
Are they still selling them? Or they ran out of business. I am on the process to get one for my fbody but they don't answer the phone
@Brandon-LSX
2 жыл бұрын
@@headported Who knows lol. Call in the am probably better chance on getting through.
Пікірлер: 39