Wow, you should keep the hvac installations to the experts.
@jayt4952
Жыл бұрын
I lean the unit 1 or 2 degrees to the front so the coil will drain and not hold water
@mastandw
2 жыл бұрын
Did you install txv?
@pamgalicki
2 жыл бұрын
nice videos, where is part3?
@MrPostFrame
2 жыл бұрын
Kind of forgot to do it 😂
@capsulax420
Жыл бұрын
Great video Where is part 3 ?
@MrPostFrame
Жыл бұрын
Forgot to post it 😂😅
@juanbriones6877
Жыл бұрын
THANK YOU FOR ALL THEM INFO. IT SHOWED ME HOW TO INSTALL THE UPRIGHT UNIT. THIS VIDEO WAS THE ONLY THAT WENT THUR STEP BY STEP. GOOD JOB.
@leedchristensen
2 ай бұрын
Can you post a link to part 3? It doesn't show up in the play list or to the right where you'd expect.
@crazyvonie
Жыл бұрын
I didn’t see the fire up video and adjustment do you have that?
@HazItMade
3 жыл бұрын
Please keep in mind that PVC is NOT resistant to UV light coming from the sun. As such, the IRC (International Residential Code) requires that exposed PVC be painted so as to prevent its structural breakdown over time. Excellent work, young man! Keep it up!!!
@banditjack1210
Жыл бұрын
They don't require that here in michigan
@tyrelgranger8105
11 ай бұрын
Where is part 3?
@serenity6988
Жыл бұрын
your gas line sediment trap is not not correctly sir?
@chaseburns2614
2 жыл бұрын
Where is part 3
@richarddiebold9106
2 жыл бұрын
Yes please, Part 3 would be great to finish job
@martinkoenig172
3 жыл бұрын
I think you would make a good teacher, 👍
@princepa123
3 жыл бұрын
You never cease to impress, one accomplished individual. Keep them coming Paul!!
@seanmacdude
3 жыл бұрын
I find your videos very instructive and I like they way you explain things
@mmanut
3 жыл бұрын
The Quality is in the details, FANTASTIC JOB, GREAT VIDEO‼️👍👍. Vinny 🇺🇸
@portalkeeper978
2 жыл бұрын
The sediment trap you built is actually a drip. The gas needs to change direction to collect any sediments.
@jeffjeff4307
Жыл бұрын
HOW CAN I GET YOUR VIDEO PART 3? SINCE MY SYSTEM NOT WORKING NOW BUT WORKED LAST SUMMBER THOUGH THE OUTSIDE MACHINE WORKING AND BLOWER WORKING TOO NOW? THX
@planetvance
Жыл бұрын
What about the compressor and condenser outside? What about the liquid and vapor lines? What about evacuating and charging the system with 410a? Where is Part 3?
@picklerix6162
2 жыл бұрын
That polyurethane caulk is the best stuff to seal vent flashings.
@MrPostFrame
2 жыл бұрын
Thanks for watching!
@gvdhhfvv
2 жыл бұрын
This guy lives in a perfect world.
@SirAnthony25
3 жыл бұрын
Paul you constantly amaze me ,keep up the good work! God bless you and your family!
@thatguy4234
3 жыл бұрын
*cough drip leg is wrong 😁 Rest looks amazing!
@remushaynes2693
3 жыл бұрын
greetings mr. paul; i just use a long nose lighter to check for leaks. it is not as messy. also i had a problem with my air vents like you have because wasps went inside and built a nest that basically suffocated my furnace. they make round snap in screens (stainless steel) that fit the pipe fittings and they are online for purchase. they sure saved me..................g
@skylarkovack2561
3 жыл бұрын
I hope your videos are way behind actual progress and your AC is already running! 🔥😜
@joshua-the-seer8494
2 жыл бұрын
Also should only use non-corrosive leak-check fluid. Cheap enough. Won't corrode metal pipe & fittings (unlike water)
@invernante1985
3 жыл бұрын
Very clear explanation for someone doing it themselves. Great video once again. You amaze me at the many different trades you are qualified and confident on the house build. Congratulations
@williammarik6159
3 жыл бұрын
Outstanding work..,looks great !!!
@AaronPowellvox
Жыл бұрын
That drip leg is wrong.
@padraic04oohhc58
Жыл бұрын
One thing id change is the switch on the the side of the furnace, id put it on the wall so you don’t accidentally flip the switch while servicing the unit
@lenrodgers351
Жыл бұрын
Do you have to put the low pressure switch in the gas line if it is natural gas.
@MrPostFrame
Жыл бұрын
No it’s just for LP since it comes from a tank vs a natural gas line
@davidmika7049
Жыл бұрын
Your gas drip leg should have been installed so there was a change in direction for the gas. The way you have it can allow for debris and moisture to be pushed across the tee. Otherwise nice work!
@joshuaseaton4526
Жыл бұрын
Also, you never put anything on top of a concentric kit. They are designed for water to go down. You just caused pressure switch issues. DIY, lol.
@Balticblue93
Жыл бұрын
Most definitely... I literally cringe when I list out how many items are incorrect and need re-done or changed.
@C-Sch
2 жыл бұрын
Thank you this vid helped me so much!
@MrPostFrame
2 жыл бұрын
You're welcome!
@rugerdogg5316
2 жыл бұрын
Nice work ! Needed this video. If you didn't show this no one would be able to comment on some of the things that need to be addressed so we all learn. Great job. PROFESSIONAL!
@evan-edstrom
3 жыл бұрын
It's not worth changing, but I prefer to put the furnace switch at the wall so I can shut off the entire MC drop. That way if you needed to replace the unit or rewire something, you don't have to shut off the whole circuit. To do this you have to have a box extension that the MC comes out of the bottom and the switch mounts in front of. Then you don't even need the junction on the side of the unit, you can put the MC elbow straight into the furnace cabinet.
@tptwk
3 жыл бұрын
I was thinking the same thing
@lhb4031
3 жыл бұрын
in easy access point from doorway to mechanical room.
@joelfriesen6191
3 жыл бұрын
Where I live the exhaust needs to be system 636 to last overtime with the heat fluctuations. Also need to be sloped 1/4" per foot back towards the furnace for condensation especially if the vent is running through an unconditioned space. With a hanger or support every 4 feet. Not sure if these regulations are required where you live.
@Balticblue93
Жыл бұрын
To the best of my knowledge, that is code in all states for the PVC exhaust venting. It was literally built to be that way, so there is no way vertical would pass code. It would backflow into the system and what would be the point of having the rules in place. I made this post on the first video. The exhaust has to be re-done, on top of several other items.
@wallaceloper637
3 жыл бұрын
Good camera work on the running of pipes and wiring. just saying
@MrDylfen
3 жыл бұрын
The Wago connectors comes in a lever version, then you can connect stranded wires.
@mikemmikem2758
3 жыл бұрын
Do you have an exhaust fan in the utility room?
@T_157-40
3 жыл бұрын
Good idea!
@lhb4031
3 жыл бұрын
be careful some can cause negative pressure. got a story for that one.
@andrewdarbyshire9108
3 жыл бұрын
You need an acid neutralizer to protect the PVC from the furnace drains.
@cdubs1723
3 жыл бұрын
Glad to help with the horizontal drain pan. Surprised you read that and took into action. I install Goodman everyday so if you have any other questions hit me up!
@joshua-the-seer8494
2 жыл бұрын
Might be good to insulate your Ducts, also install an EZ Trap Condensate Drain Trap with Automatic Safety switch to prevent overflow when Drain Clogs (Which it eventually will...)
@wattjock
Жыл бұрын
An SSU Switch is typically used for the furnace, and I agree, albeit a negligible point, to install it on the wall... too, while not a Code issue, it is usually standard practice for switches to install the line side on top of the switch and load side on bottom... just for uniformity in switches throughout a project. Otherwise, very comprehensive coverage of the install! Appreciate the video posts!
@alexgiron3079
2 жыл бұрын
Your work is very good, is possible send to me the part 3 please, thanks
@MrPostFrame
2 жыл бұрын
Still working on Part 3. Hope to have it out soon.
@johnnyb8629
3 жыл бұрын
Always use a grommets or chase nipples when running wire through metal knock outs. Also, the condensate if highly acidic, may want a neutralizer on that, not sure what that does to a septic system.
@renep.l.1580
2 жыл бұрын
So what type of wire should I used and what size breaker? That you didn't explain but great video .
@Cody-ye3ye
3 жыл бұрын
Drip tee in gas is wrong
@Balticblue93
Жыл бұрын
Amongst 37 other things that are incorrectly done.
@nettyklar9807
3 жыл бұрын
remember to put a red plate for the switch because its a gas furnace
@scottjenkins844
3 жыл бұрын
You should extend your coil condensate vent line higher than the safety switch and with the ss2 installed how will you be able to spin out the primary drain?
@tier3rd375
2 жыл бұрын
The sediment trap isn't installed correctly. You want to install it in a way where the gas is flowing straight down so that sediment is falling into the trap. The way you have it has gas flowing across it which could allow some sediment to get past it.
@davids970
2 жыл бұрын
You don't have to goose neck the concentric ,the 90% furnace drains. The intake on the concentric is under the exhaust covered with that funnel piece If you did a 2 pipe you have to goose neck the intake .
@joshuaseaton4526
Жыл бұрын
Yep, he caused issues with that furnace.
@wizardmaster6639
2 жыл бұрын
Did I see the exhaust pipe and fresh airline merging? 18:40
@MrCvjef
2 жыл бұрын
Is there a part 3?
@JBernhard72
3 жыл бұрын
You need an air gap on that drain.
@mdjohnson03
3 жыл бұрын
I don't mean to be degrading or otherwise. But after seeing this I feel like I should say something. As a licensed journeyperson in Iowa, and mechanical instructor. Your condensate (tied directly to sewer without an air gap, improper venting, improper trapping), gas line (improper drip leg location), electrical (missing protection from J box to furnace chassis), and flues (no insulation in unconditioned space, screws protuding pvc pipe, exhaust cannot be terminated down on category 4 venting system, cannot have obstruction in exhaust, and improper or lack of proper support) are not up to mechanical code nor your installation manual, and you will experience many issues. And please under no circumstance tie your intake into the condensate sewer line as you will draw methane gas into combustion. Any manufacturer will also void the warranty on this product if you run it like this.
@jasoncanmore5838
3 жыл бұрын
Where should the drip leg be located?
@mdjohnson03
3 жыл бұрын
@@jasoncanmore5838 it should dead head into a drip leg. Example would be to install a T fitting on its side right outside the furnace, bring the gas supply through the top of the T, furnace to be connected out the side of the T, and a nipple with a minimum length of 3" as measured from hub to hub (so you would need a 3.5 -4" nipple) with a cap on the bottom. This forces any moisture, oil, and debris to be collected in the drip leg and not allowed to flow right past into the appliance.
@jasoncanmore5838
3 жыл бұрын
@@mdjohnson03 Got it, thanks
@xincai951
3 жыл бұрын
You have to insulate flues in unconditioned space?
@darrenmattan647
2 жыл бұрын
After watching the video I needed to see the comments cause my brain was throwing off a couple of red flags the screws In the exhaust are gonna rust and it will probably recirc. Let alone not insulating the vent in un conditioned space could possibly freeze up
@lhb4031
3 жыл бұрын
doing a great job Paul. do't forget to have a friend check it out before you fire it up. or soon after so you can change anything that you think you should to. not a sin to do that. back in June i am a little late. sorry
@BretBerger
3 жыл бұрын
Doesn't look like you got a bushing on the hole between single gang switch box and interior of furnace. Might be an issue with vibrating equipment wearing a hole in the wire insulation over time.
@lhb4031
3 жыл бұрын
through a rubber grommet in it.
@williamgreen4757
3 жыл бұрын
So please use wire nuts at the furnace/ac house junction box, The furnace cycles many times per day with a high amperage draw at startup. The legos could ark internaly duting high amp draw heating up and causing even higher amperage as the voltage drops. ps good luck, high power communications tech.
@mikemmikem2758
3 жыл бұрын
I had the same thought. Wire nuts are the way to go as long as a pliers are used to join the wires first. Wire nuts were never designed for this purpose.
@christopherhaak9824
11 ай бұрын
Wire nuts might be better, but that furnace has a max drawof under 9 amps, it's never high.
@davidfrisch5538
Жыл бұрын
Very clear and professional video .. always clean work ! I did have a question on your venting .. looks like you used 2" the whole way , did you ever have to step up to 3" after making this video ? .. my new goodman came with a chart in the manual . With how many feet with so many elbows , for 2" 3" runs . I'm only running less than 15 feet so I was hoping to stay with 2" . Want to see if you had any issues . Thanks for taking the time to make these types of videos
@MrPostFrame
Жыл бұрын
Runs perfect. I ran 2” the entire way.
@markc2404
3 жыл бұрын
Will you be adding a humidifier for winter months.
@joemizer
3 жыл бұрын
Why did you go thou a rib in the roof?
@mastandw
2 жыл бұрын
Great videos and explanation. May I ask you couple of questions 1. Where did you purchased the furnace (the entire unit) 2. You mentioned the part 3 would show how to install the wiring to thermostat and other stuff, I could not find one. Thank you in advance.
@MrPostFrame
2 жыл бұрын
We purchased the unit through a local place but have used AC Wholesalers in the past with good luck. Part 3... kinda forgot to put that video together but it's on the list!
@mastandw
2 жыл бұрын
@@MrPostFrame thank you for the details. Once again your videos helped me to do home improvements and lot of motivation. I am planning to purchase goodman furnence and heat pump through hvacdirect. With your motivation I will can do atleast 80% of the installation and will take help of contractor on the final setup and installation. Thank you.
@glen748
3 жыл бұрын
Question: When you ran the air intake/exhaust pipe out through the garage roof. Why did you have the pipe go through a rib and not a couple inches over so that it was totally in the flat of the metal roof? Wouldn't this have made it easier to install the boot and create a better seal? Also where does the furnace filter go or did I just not see it.
@barryschuschke9149
3 жыл бұрын
I noticed the same thing. There might be a reason for this. Thanks for letting us follow your build.
@cdubs1723
3 жыл бұрын
Water rushes down the flats. Using the ribs, help shed water and not having running water into the seal directly.
@alanm2842
3 жыл бұрын
you are going to be short on return air. with a side return like yours and on motor side makes it worse. furnace needs to be on a raised box with return at bottom so return air can get around to other side of fan. this became a problem when they made furnaces really short. check the instructions that came with furnace. condensate is never hooked direct to a sewer line, must have a air gap
@stevenbrowningsr1144
3 жыл бұрын
Air gap??
@alanm2842
3 жыл бұрын
@@stevenbrowningsr1144 air gap is a plumbing term. it is hard to describe so i would ask that you google, what is a air gap
@darrenmattan647
2 жыл бұрын
Agreed, I see it all the time on goodmans ends up with high co problems/overheated heat exchangers, the more return the better with any new 34" furnace. Idk about the states but in canada we are supposed to insulate the pipes going through unconditioned attic spaces so the exhaust doesn't freeze.
@StevenCrothers
3 жыл бұрын
First! Great job on the house!
@patrickmoore7607
3 жыл бұрын
I hate to be a critic, especially of someone with an amazing amount of talent like yourself. I really don't trust the push to connect electrical connectors. The lever lock wagos i can get on board with those, but the push to lock ones ive heard too many horror stories
@thomasburgess1605
3 жыл бұрын
this may be a stupid question on the roof vent , any chance of bees or hornets making a hive in it ?. not sure if that's a problem in your area .
@smithbrothers125
3 жыл бұрын
Once again you have no idea what you are doing. You DO NOT add piping to a concentric vent.
@Erik_MN
3 жыл бұрын
Was it deliberate locating the vent on the rib of the roof steel?
@wrfarms9741
3 жыл бұрын
Maybe I missed it but did you install a one way check valve on the condensate drain so water cannot back up through the drain into the evaporator pan? It happened to us and it was a mess.
@jimmydavis6954
2 жыл бұрын
No he did not install any check valves , he did install a float valve which will cutt off poweer to the unit if the drain starts backing up
@rodgraff1782
Жыл бұрын
No primer on any of your PVC joints? It’s usually blue, so the inspector knows you used it. Automatic code failure in my area. The concentric termination should not have any pipe or fittings added to it. What you have done could actually cause flue gasses to recirculate into the combustion air under the right conditions. Big no no.
@duartemonteiro7463
3 жыл бұрын
I am impressed with your work Paul! Extremely perfect! 😊💪💪💪
@Cody-ye3ye
3 жыл бұрын
Where did the down drop come from if mfg wanted that they would send it with the conc kit, venting in unconditioned space should be insulated you obviously didn’t read the book
@CollinEichinger0221
3 жыл бұрын
I love watching you install stuff like this in your house. You do WAY better than any contractor I have ever seen!
@bradmoyer9737
2 жыл бұрын
Obviously the work you’re doing on electric, gas plumbing excetra is legal for you to do. What is the situation for all of the regulatory inspections normally required for working on these systems? This is not an indictment against your work, because everything I’ve seen you do is usually to a higher standard than minimum requirements, just wondered if it is because you’re in a rural location instead of an incorporated city. Thanks for the content, very interesting and enlightening!
@MrPostFrame
2 жыл бұрын
Rural locations tend to be less involved when it’s a personal home build. It can be a blessing and a curse depending on someone’s knowledge and skill
@taconinja4046
2 жыл бұрын
90% right?
@dougsharpe7544
Жыл бұрын
You really need to read the instructions before you make videos, I've been in HVAC for 48 years
@Balticblue93
Жыл бұрын
He needs to do more than read the instructions, he needs to bring in one of us properly qualified technicians or installers to fix all the improperly installed items. I cringe when i watch the videos. This system is going to have so many issues and will never pass code inspection.
@cuznjo1
3 жыл бұрын
here in NY, the switch and cover for the power has to be RED
@s72880
2 жыл бұрын
your sediment trap is installed incorrectly. It should have a change in direction in gas flow. As you have it, "sediment" will fly right over your trap and never go into it.....
@joshuaseaton4526
Жыл бұрын
Yep, and the sediment trap is worthless. Hire a pro next time. So tired of these videos.
@Balticblue93
Жыл бұрын
DITTO!! This is ridiculous. I feel like flying there to fix all the issues for free because it freaks me out how many mistakes have been made and how it will never pass inspection let along work properly. These videos kill me and are hard to watch.
@68Jaguar420G
3 жыл бұрын
5:30 Ok Paul, If you have taken out the evaporator (A-frame coil) drain pan how are you catching the condensate off the evaporator and directing it out to the drains? Something sounds odd here or I'm not understanding what you have removed.
@dcmchiefs2008
3 жыл бұрын
I believe there are 2 different pans in the unit because it is designed for a vertical or horizontal install depending on the house. So I think he's saying he removed the drain pan for the horizontal mounted application.
@Balticblue93
Жыл бұрын
@@dcmchiefs2008 The A coil needs to be removed from the unit and a condensate drain pan needs to be added but that is the least of his worries after watching the entire video. I hate to see video #3 but I don't believe that was ever made or uploaded.
@christopherhaak9824
11 ай бұрын
That's wrong, this comes as a dual mount furnace, so it has two drain pans and he removed the horizontal one. All of the cased A coils come with built in drain pans. It's all good for this part
@Beliay76
3 жыл бұрын
Сделай перевод на Русский а то Я так и буду дизлайки ставить. Make a translation into Russian, otherwise I'll put dislikes.
Пікірлер: 127