Perfect! Answered all the questions I had. I usually just hit like when a video is helpful but the quality and detail of your videos on the Mustang II kit install anjd the comparison video made me have to comment. Great job!
@GODSPEEDGarage
3 жыл бұрын
Glad it was helpful! THANKS FOR WATCHING! make sure to like and subscribe if you want. THANKS!
@williesims3152
2 жыл бұрын
Awesome Job Man! Thanks for being so thorough!!
@GBray
3 жыл бұрын
Your a natural teacher. Informative, clear and easy to understand. Great videos . I'm now subscribed. Thanks 👍 Watching your videos helps motorvate me to get off my A--.
@GODSPEEDGarage
3 жыл бұрын
Thanks and welcome
@glenmiller3783
4 жыл бұрын
Great videos, I installed pretty much the same kit in my 28 Dodge, there is a weak spot you may want to address. At 217 in the video is a good shot of the lower control arm mount. All your braking forces are pushing rear ward and inward on the the back end of the the shaft in the lower control arm and there is nothing attached to the frame other whats in the cross member and the short bushing. On mine I added two brackets down from the frame for the rear bushing to mount in, you could add one down from the frame on the rear side of the bushing.
@larryhollinger1891
Жыл бұрын
love your videos!!!! always thorough and well explained. you don't skip the little steps and that's helpful to novice guys like me. Great job and thanks
@HyperArsenal
3 жыл бұрын
As a 20 year old building my first rat rod out of a Chevy luv this channel is so much help thank you for the knowledge you provide us
@GODSPEEDGarage
3 жыл бұрын
that is awesome! love to see young guys getting into hotrodding!!
@buildingconsultants1854
Жыл бұрын
Excellent work... nice and clean an a great narrative. the details make all the difference. Thank you- really appreciate your in depth videos
@Mm-ik9uq
Жыл бұрын
Just a question and you might have already done it and just forgot to mention it did you center the rack when you installed it? In other words found the half way point right and left?Thanks looks good..
@DeeDago
4 ай бұрын
Do u have any info om how to address slop in the steering wheel. My car drives but has some slop in it. Is there a way to adjust or tighten the sterrimg gear box? Thanks
@misterbulger
2 жыл бұрын
Picking up a Mustang 2 front end for FREE tomorrow... will be dropping it into a Geo Metro for the front half of my 302 swap. Appreicaite you helping me visualize what needs done.
@damiansailas6296
Жыл бұрын
I really wanted to see something on the steering column and the angle in which it hooked up...the end for that mustang front end...i have a 51 mustang front end and wanted to compare the part to your build....?
@silvosshop
4 жыл бұрын
Hey brother. Great video. I’m installing the same IFS and the rear race on the brake rotor doesn’t want to go all the way back and “seat” leaving me enough room on the front of the spindle for the front race, washer, and castle nut. Did you have any issues as you seated the rotors? Didn’t appear you did just have to ask for your wisdom. I wish I could post a pic to show you what I mean. Thank you!
@joeclardy2388
2 жыл бұрын
Thanks for taking the time to video. The info was very helpful.
@GODSPEEDGarage
Жыл бұрын
Thanks for watching!
@GustavoLopez-wz2jd
3 жыл бұрын
Hello, good night, I need advice, I bought a kit47-54 Chevy Truck Mustang II IFS Coil Over Stock 5x4.5 Power LHD, my question is which steering pump do you recommend to fit it, it will be fitted in a 1952 truck with its original engine. Thanks
@twoslowable
3 жыл бұрын
Nice job. I'm thinking about going this route on a 61 comet
@TMD4343
10 ай бұрын
Great video, I like to stick to aerospace standart, bold heads always go up or fwd,
@martinmartinez2455
4 жыл бұрын
Thnx for the videos.i have a 53 belair and u have inspired me to do myself. Keep them coming 👍👍
@johniex3000
4 жыл бұрын
Great job, very nice how you illustrate the build.
@TheLuckyone760
4 жыл бұрын
With 2 inch drop spindles I had to cut the spring to get around 11 inches in height.
@gregmaggielipscomb9246
9 ай бұрын
Nice work, pls keep at it.
@MrMechanicandy
Жыл бұрын
Didn’t mention the top ball joint should be of center to the rear to give it more positive caster .
@OutlawChevy2
Жыл бұрын
Great instructional video my friend!
@CountyGarage207
Жыл бұрын
Thank you for these videos. I'm about to start building a 64 international scout, and want to use a mustang 2 front kit like you did. The only issue I see is my frame rails are 29" inside to inside, and 35" outside to outside, but the speedway kits seem to be much narrower. Hopefully I can think up a solution!
@GODSPEEDGarage
Жыл бұрын
contact speedway. they would know. thanks for watching!
@CountyGarage207
Жыл бұрын
@@GODSPEEDGarage I wound up getting it done! I used a kit for a 55-59 chevy truck from speedway motors, and measured the frame of a 58 a friend has so I was able to modify my frame to use the kit. It worked out perfect.
@crictor320
2 жыл бұрын
Hi there, did you ever solve the problem with your power rack boot touching the lower control arm bolts? Im having the same issue
@GODSPEEDGarage
Жыл бұрын
yes! I just put a washer or two between the rack and crossmember. worked great!
@victorrobles4672
4 жыл бұрын
I just started watching your videos they are great, I have a 66 c10 that I want to replace the front cross member(I'm doing bags and want it bodied) but don't have the $$$$ to get one from "GSI", "Porter Build" or "Chopping Block" they all are in the $3k range, do you know if there is a Mustang ll for 66 c10 any recommendation will be much appreciated, thanks.
@soooop2
3 жыл бұрын
I have the gearhead kit that looks like yours . Do you know what rotors these kits use. They sent wrong ones and would like to be able to replace locally . Thanks
@GODSPEEDGarage
3 жыл бұрын
should be standard 1970s Mustang II rotors - 74-78 Mustang II, 74-80 Pinto... they may be different due to bolt pattern. I would contact the manufacturer of your kit to confirm
@randomrepair1680
Жыл бұрын
Awesome job. Was a big help
@GODSPEEDGarage
Жыл бұрын
Glad it helped
@nitrofunny23ify
3 жыл бұрын
I ran into the same issue with the steering boot hitting the mounting bolt on my Heidts Falcon IFS. I spaced it with 3 fender washers on each side. Problem solved!
@GODSPEEDGarage
3 жыл бұрын
that's what I ended up doing too! thanks for watching!
@chaserivers4058
3 жыл бұрын
I ran into the same issue with a speedway kit (entire kit from speedway)..... called tech support and they acted like it was my fault!!!!! Those bushings should be longer, a few washers on mine solved the problem too.
@Sgtmidnite
4 жыл бұрын
Thank you so much! Keep them coming!
@guillermonieri4203
4 жыл бұрын
Thank you for sharing. It is looking good.
@petelavelle7987
3 жыл бұрын
Sure hope this works for my '53 Chevy Sedan Delivery...
@brianhaw9398
2 жыл бұрын
I'd like to see a turbo 4.2 from a trailblazer in one of these. I know now you are doing the 5.3 ls. Either way I'll watch
@rossmason4434
Ай бұрын
Awesome
@wardfrahler6779
2 жыл бұрын
What did you do about the rack spacing?
@GODSPEEDGarage
Жыл бұрын
I added a washer behind it to space it out enough. worked perfectly
@chucksgarage7165
4 жыл бұрын
Why would you clean the rotor before you pack the bearings? Why not do it afterwards in case any grease gets on them?
@GODSPEEDGarage
4 жыл бұрын
why not do both? pretty sure i cleaned before AND after... new rotors have some casting residue... you DO NOT want that in your grease. any dirt, metal flakes, etc will work it's way into your bearings and shorten the life. THANKS FOR WATCHING!!
@chucksgarage7165
4 жыл бұрын
GODSPEED Garage that’s probably the best approach.
@nathanmurdock3213
Жыл бұрын
Great video!
@jodyjnlv
3 жыл бұрын
Dude nice video thanks for sharing , are you using stock wheels and if so do you have any clearance issues?
@GODSPEEDGarage
3 жыл бұрын
they are 15" steelies. stock came with 14", which would have clearance issues. but anything 15" or bigger should be fine. thanks for watching!
@adamvalenzuela6626
2 жыл бұрын
Why would you have to cut coil springs?
@GODSPEEDGarage
Жыл бұрын
to level the car depending on your engine and transmission weight. it's the only downfall to the Speedway kit, but I would still recommend it. THANKS FOR WATCHING!
@ronaldlewis2041
2 жыл бұрын
Great job, are you still working on the project?
@GODSPEEDGarage
2 жыл бұрын
yep! there is a playlist with all the videos. I'm building a 5.3 Turbo LS for it!!
@kevinlyons2739
3 жыл бұрын
Great videos - I'm curious how you installed the original steering..
@GODSPEEDGarage
3 жыл бұрын
haven't done it yet... I'm currently building the engine. once I get it installed where I want it with exhaust and everything I'll do a video for steering. planning on installing a bearing, then connecting the shaft to a double D shaft via u-joint, then connecting to the steering pump with the correct adapter. I may have to trim back the frame rail... it's coming along... slowly, thanks to pandemic slowing down parts availability and machine shops... good times... stay tuned!!!
@brianhaw9398
8 ай бұрын
There is another youtuber called sneden werx( or works) He did a similar build and shows the way he did his steering😅
@Sgtmidnite
4 жыл бұрын
Why did you choose the Heidts crossmember instead of the Speedway one? Thanks so much for the videos!
@GODSPEEDGarage
4 жыл бұрын
i already had the heidts one. originally i planned on using it with the components from the Helix kit, but that kit went to hell, and dealing with Johnny Law Motors, Helix, etc. (all the same company) i went through 7 layers of the worst HELL ever!!! ha! i bought the crossmember from Summit, it would've cost $25 for restocking plus shipping. so i just kept it to use with the speedway kit. it worked out GREAT and i'm soooo happy i went with speedway instead of that horrific Chinese kit from Helix...
@hillbilly59apache59
4 жыл бұрын
That is amazing job 👍👍
@GODSPEEDGarage
4 жыл бұрын
thanks!! i have a 58 apache as well! love that truck...
@MrMechanicandy
Жыл бұрын
That isn’t much torque for the upper caliper bracket if it’s a 1/2” bolt
@michael5point0
4 жыл бұрын
Nice video, I have a 1931 Buick in which I'm looking in to doing this set up.
@licha5050
2 жыл бұрын
awesome vid! thanks
@carlosbuscaglia1409
Жыл бұрын
What brand is that kit?
@GODSPEEDGarage
Жыл бұрын
sorry I think I forgot to mention in this video... it was in the description in Pt. 1, but I added links... it's a Speedway Mustang II kit with the Heidts Crossmember. hope that helps!
Пікірлер: 73