If he makes a video of this hack job can you imagine the ones with no video.
@MrOumarking
7 жыл бұрын
what a simple but excellent video. Thank you Mr. Ferreira !
@gg-oz8jn
5 жыл бұрын
Nastyyyy job man lol....
@smash72cutlass30
6 жыл бұрын
He also constricted that drain with that rubber insert by at least 1/2 inch which means most likely a nice pond that will clog the strainer
@chrislesperance8342
7 жыл бұрын
theres a broken clamp ring for sure and that mod bit adhesive is for cold application
@josephbonham4127
6 жыл бұрын
Not to mention the marked up ugly white cap that went on top
@michaelsymons9098
2 жыл бұрын
i normally start from drain and work out
@detumaki
7 жыл бұрын
ok first off, dont use karnak adhesive use plastic cement. it will seal better and prevent fire. in fact, Certa would probably be grabbing that torch real fast if they see it. secondly you did not prime the bottom or top of metal and it WILL LEAK. YOU HAVE TO PRIME METAL WITH ASPHALT PRIMER NOT CHEAP ADHESIVE. now your adhesive will gunk up and crack allowing gaps for water on top of it will also separate from the metal. lastly, that adhesive you used on the metal will eat the finish on that metal and cause a, hypothetically speaking, 50 year metal finish to deteriorate in less than half the time causing rust and separation. also, dear Lord you overheated the membrane but still failed to bleed it properly. Also, rubber washer at end is plastic, but that's nitpicking terminology. not spec or code.
@damirgracanin1293
5 жыл бұрын
The target pach grannual cap sheet over grannual sheet cannot seal so that is incorrect right there but you are a torch down specialist you already knew that right
@mikejohnson7768
6 жыл бұрын
noight man
@corporate156
3 жыл бұрын
This is 2 plys sistem, no 1 ply sistem
@kociarz46
Жыл бұрын
All I have to say is biggest YO-YO AND KING HACKER
@VideoGrabBag
8 жыл бұрын
Missed a very important part between 2:00 and 3:00. How was it repaired???
@JosephJBokano
4 жыл бұрын
The rolls he used for repair are stacked up right behind in beginning of vid.
@rubencarbajaljr.310
7 жыл бұрын
Wth is this?? I've put these on before/I've always primed them and I slightly tighten the rubber seal so it won't fall off when going in the pipe which it goes in smoothly not like here then I tightened it ohh and I torch smooth over top then my granulated material
@WaIIyMaven
3 жыл бұрын
A few twists of tape around the joint between the Uflow drain adapter and the retrofit drain will help keep it in place
@rubencarbajaljr.310
3 жыл бұрын
@@WaIIyMaven Lol I forgot this "tutorial" existed 😅 🤣 🤦♂️ thanks for the laugh again
@dekonfrost7
8 жыл бұрын
Only thing I can say it that the framing needed repaired so the drain fits flat and fully supported. Which you elected not to do.
@dekonfrost7
8 жыл бұрын
I agree with a lot of what you have to say
@WaIIyMaven
3 жыл бұрын
Dekonfrost7, bless his heart about all he got right is that roof drains are critical.
@MsAcube
7 жыл бұрын
excellent video - thanks or putting in. Can you please put the model of drain
@chaddles623
7 жыл бұрын
It's a OMG Hercules Retro-Fit Roof Drain
@WaIIyMaven
3 жыл бұрын
Aditya, he did a bad job on just about everything. And Menzies makes a nicer aluminum drain without being too pricy
@juanwatts8095
4 жыл бұрын
That's not the proper way of doing the drainage that guy dont know bout roofing
@dekonfrost7
8 жыл бұрын
The first 2 minutes of this video I tell people and customers just look at me with glassy eyes. Totally not compressing what I am saying
@stewartredman9785
4 жыл бұрын
This guy has absolutely no idea what he is doing. Nothing in view of the roof on this video is correct. He has actually created a back lap in the worst spot on the roof. His drain application only required a torch, app modified torch ply and some primer.
@krissiwy7967
3 жыл бұрын
And the skills to do this job. He don't have any skills with the torch.
@krissiwy7967
3 жыл бұрын
You are the biggest mistake. You should prime the drain first and then torch down 2 play. But you like to put this stuff,because you don't have a clue how to do this job proper way.
@chrishortie1500
7 жыл бұрын
you don't have a clue what you are talking about! That is some of the worst torching I have ever seen! My first year apprentice does better work. You should not be giving any advice on the application of anything....
@MegaSandman1977
7 жыл бұрын
Chris Hortie shut the fuck up
@martinjvillasenor773
3 жыл бұрын
You are right Chris . . . This guy is a total amateur!
@krissiwy7967
3 жыл бұрын
I see so many idiots out there,who likes the work he did. Any flat roof guys who ever torching will laugh at them. I mean guys with the skills,not like Doctor Butcher.
@gerarddooley1520
2 жыл бұрын
How does that lad get work,he hasn't a clue,slap a load of crap around an outlet an cover it in cap sheet, hope he's not getting money for that shit work
@pyrex_kidd815
2 жыл бұрын
To think people pay you to fix there roof!! 🤷♂️ I honestly don't think you did anything correctly!! Please don't listen to this man! 🙏🙏 🙏 🙏
@jasonlovett7665
3 жыл бұрын
Quality of work is terrible.
@xxdrloveleyxx5185
2 жыл бұрын
A 1 ply drain. wow doing that shit where iam from youd be picking garbage everyday all day. worst hack ever but hey the more people tell him the more he learns lol
Пікірлер: 40