We are going to install and test a Corsa Air Intake for a 2020 Mustang GT. The goal would be to obtain a baseline HP/Torque measurement on our "factory" Mustang, then install our new intake and retest to verify results (HP/TQ difference). The Dyno Runs will be done only a few days apart with the same fuel and temperature conditions (to minimize outside factors).
Note: Per CORSA, "Disconnecting the battery before installation may reset the computer and clear old air flow data to help prevent CEL errors."
Supporting Documents
Dyno Run (Before) - drive.google.com/file/d/147mK...
Dyno Run (After) - drive.google.com/file/d/19LQH...
Dyno Run (Both) - drive.google.com/file/d/1oERE...
Installation Instructions - drive.google.com/file/d/1_xTg...
Supporting Videos
Sound Tube Delete - • How to Uninstall the S...
Strut Tower Brace Install - • How to Install a Strut...
1. 1st (Baseline) Dyno Run - 0:19
2. Step 1 (Remove Battery Cover) - 1:06
3. Step 2 (Remove Battery Terminals) - 1:23
4. Step 3 (Remove Strut Tower Brace) - 1:51
5. Step 4 (Remove Engine Cover) - 2:28
6. Step 5 (Disconnect MAF Sensor) - 2:45
7. Step 6 (Remove (Small) Breather Hose) - 3:08
8. Step 7 (Remove (Large) Breather Hose) - 3:37
9. Step 8 (Remove Duct from Throttle Body) - 3:57
10. Step 9 (Remove Duct/Upper Airbox) - 4:22
11. Step 10 (Remove Lower Airbox) - 4:46
12. Step 11 (Remove Sound Tube) - 5:12
13. Step 12 (Remove MAF Sensor) - 5:38
14. Step 13 (Remove Bushing & Grommet) - 6:06
15. Step 14 (Install Bushing & Grommet (New Box)) - 6:59
16. Step 15 (Install New Air Box) - 7:30
17. Step 16 (Install Bulb Seal Trim) - 7:58
18. Step 17 (Install MAF Sensor) - 8:39
19. Step 18 (Install Small Breather Fitting) - 9:32
20. Step 19 (Install Large Breather Fitting) - 9:51
21. Step 20 (Install Silicone Reducer) - 10:07
22. Step 21 (Install New Air Duct) - 10:43
23. Step 22 (Install Lid) - 11:40
24. Step 23 (Connect MAF Sensor) - 12:03
25. Step 24 (Install Small Breather Hose) - 12:12
26. Step 25 (Install Large Breather Hose) - 12:28
27. Step 26 (Trim Engine Cover) - 12:54
28. Step 27 (Install Engine Cover) - 13:39
29. Step 28 (Install Strut Tower Brace) - 13:54
30. Step 29 (Install Battery Terminals) - 14:12
31. Step 30 (Install Battery Cover) - 14:40
32. 2nd Dyno Run - 15:08
33. Show it Off - 15:47
Products Used:
This video contains affiliate links for which I may receive compensation.
Air Intake - amzn.to/3J45TZ2
- www.corsaperformance.com/prod...
Extension Bar Set - amzn.to/3xjgb4N
Fuel Line Retaining Clips - amzn.to/43Mqj2m
Nitrile Gloves - amzn.to/4awsDMK
Trim Removal Tool Set - amzn.to/4cxTTfI
Tools:
1/4" Socket Wrench
1/4" Extensions
7mm Socket
8mm Socket
10mm Socket
15mm Deepwell Socket
Needle Nose Pliers
Oscillating Tool
Phillips Screwdriver
Rotary Tool
Trim Removal Tool Set
T20 Torx Bit
Disclaimer: Content produced from Mcgurr Entertainment is for entertainment purposes only. This information is not endorsed by any agency/company (such as Ford) and is intended as an entertainment. Mcgurr Entertainment assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. All content on KZitem is provided in good faith, however we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability or completeness of any information on KZitem. Use this information at your own risk.
#CAI #Dyno #Mustang
Негізгі бет Автокөліктер мен көлік құралдары Installing and Testing Corsa Air Intake on a Mustang (S550 2018-2023)
Пікірлер: 16