Quick question. On a millennium euro, how high is the La Pavoni from the counter up to the top of the gauge with the lever down. I want to make sure I still have clearance where I store mine. Thanks!
@zenmarzfirak
3 жыл бұрын
I teflon taped tube connections instead glue/blue loctite in case I have to disassemble. Seems to work fine,,,
@LaPavoniBPLUS
3 жыл бұрын
Glad to know it ! 👍🍀
@charlesa99
9 ай бұрын
Any recommendations to remove the play (wiggle) in the handle and top of the piston?
@philippep561
6 ай бұрын
play is normal till 0,20 mm
@xelaol7051
2 жыл бұрын
Does it compatible with Stradivari grouphead?
@RayBowles
3 жыл бұрын
If using a torque wrench to install is there a recommended nm setting to use on each of the nuts and bolts?
@LaPavoniBPLUS
3 жыл бұрын
In theory, this should be done, but this screw only needs to be tightened. According to screw mechanical specifications: 50kgf-cm
@OttoRolloff
3 жыл бұрын
Can I add the manometer on a basic (not professiona) europiccola too? Like, this one and the one for the tank? Thanks in advance!
@LaPavoniBPLUS
3 жыл бұрын
The extracting pressure profiling kit can be installed on both professional and Europiccola models.
@OttoRolloff
3 жыл бұрын
@@LaPavoniBPLUS , thank you very much for the info! ☺️
@franciscodelatorre9336
4 жыл бұрын
Whats the point yo install tris gadget in my La Pavoni Professional
@JoeyVaracalli
3 жыл бұрын
will this work on the expo 2015?
@LaPavoniBPLUS
3 жыл бұрын
Yes!
@nelgchannel9661
3 жыл бұрын
How can I purchase this accessories?
@LaPavoniBPLUS
3 жыл бұрын
Check : www.bplus.biz
@kirati2529
3 жыл бұрын
would this kit fit a premillenium??
@LaPavoniBPLUS
3 жыл бұрын
Yes , this kit can be installed in post & Pre millennium.
@juiceme1121
3 жыл бұрын
will this work on the Stradivari model?
@LaPavoniBPLUS
3 жыл бұрын
In case of Stradivari that lever need to replace with straight one . The new straight lever is included in the profiling kit.
@juiceme1121
3 жыл бұрын
@@LaPavoniBPLUS Thansk for the reply! That's a bummer. Any future interest in creating a compatible handle that mimics the shape of the stradivari? Kinda the main reason I bought it.
@LaPavoniBPLUS
3 жыл бұрын
@@juiceme1121 The curved handle design of Stradivari will cause the lever to interfere with the pressure gauge after being raised. So it is impossible to apply the existing design. Sorry about that ..^_^
@franciscodelatorre9336
4 жыл бұрын
Where can I buy that kit?
@LaPavoniBPLUS
4 жыл бұрын
www.bplus.biz
@coffeecoffee5914
4 жыл бұрын
@@LaPavoniBPLUS out of stock
@LaPavoniBPLUS
4 жыл бұрын
It’s available for ordering now . www.bplus.biz/products/extracting-kit-with-pressure-profiling-gauge-for-la-pavoni-lever-machine
@EUCWayOfLife
3 жыл бұрын
@@LaPavoniBPLUS does this come in a brass version for the PB-16? also why does the lever arm need replaced? and why cant the original be used?
@LaPavoniBPLUS
3 жыл бұрын
@@EUCWayOfLife the lever are came with “screw threads” for fixing with pins. Due the the shaft need to draw a through hole from the bottom of piston to top of the gauge. It doesn’t allow the first pin go through the shaft. The first pin need to divided become 2 pieces and these 2 pins have to fixing in the lever arm by thread.
Пікірлер: 29