I was hesitant to put turf on diamond plate until I watched this vid. Thanks.
@chrispeerman7445
4 ай бұрын
I think u did a job I think letting people know that it will expand in heat was a good tip. An dont think Ill b goin with the diamond pattern seen the the trouble u had piercing it together. I know to your eye it will stand out but to the untrained eye nobody is goin to notice. Good job would like to see how it holds up a year or 2 from now.
@terryogletree2128
2 жыл бұрын
I sanded my 1862 decks shiny and used the 3M backed Hydro Turf cobblestone color. $110 a sheet from Fast Duck Motors in Astor FL. I used about 5 sheets but CID just gave me a half a sheet he had it came in handy for the small areas.
@4ReelAnglin
9 ай бұрын
Looks good man! I am getting ready to do my boat with HT I think.
@Cozmicowboy
3 жыл бұрын
i think it looks great. I'm doing this on my duck boat to make it more comfortable for my lady and friends if we go out on the lake for fun in the off season. I just hope it washes out easily
@TripleRwoods
3 жыл бұрын
It does wash out good. I just posted a video of us bow fishing in my boat and it was full of blood and fish parts. Rinsed it out at the car wash and it looks great.
@MrSki-mv2kr
Жыл бұрын
Looks like diamond pattern is turnout to be more difficult than straight lines. Super thank you.
@SouthernOutfitter
Жыл бұрын
Great video brother I'm thinking about doing this aswell
@akbuilder7626
Ай бұрын
They cut the sheets by hand so the ends are uneven. Their website says each sheet only has 43 x 83 usable area even though they are supposed to be 47 x 87.
@oak664
Жыл бұрын
Turn the templet sideways. Maybe shifting to the bottom of the row above will match up or the top of the next row
@frankhunt5018
2 жыл бұрын
Looks great, I just subscribed and liked the video. Is the paint on the boat original or did someone redo it? My Jon boat has a terrible paint job, I want to paint it before installing any turf.
@TripleRwoods
2 жыл бұрын
Thanks man. That’s the original Edge paint job. I think they call it Nat Gear Black. I’m going to post an “update” video soon. Thanks man 👍🏻
@oak664
Жыл бұрын
Best to put it on when it’s hot out for better alignment of seams if you do that
@MrSki-mv2kr
Жыл бұрын
The foam doesn't like uneven surfaces like diamond plate, no wonder you got air bubbles. I have heard about people grinding down the profile of the diamond plate to make the surface more smooth. Not completely ground down but just a bit.
@joshandhuntersadventures5046
3 жыл бұрын
I could see where this might come in handy in some situations
@TripleRwoods
3 жыл бұрын
It's really a great idea, it doesn't get as hot as aluminum so fishing in the summer is way better. It helps with the noise that aluminum boats have when running on the water. Wish it was easier to install tho lol
@alexbell9196
2 жыл бұрын
Man i get hung up on details too but nobodys gonna give two sh$&$ about the pattern not being perfect. That sucker looks good
@TripleRwoods
2 жыл бұрын
Appreciate it.
@dannyneal9713
Жыл бұрын
After seeing all the trouble you have of trying to line up diamonds I’m going with the flat brushed camo look I wanted to go with the hexagon pattern with camo to match my boat but I feel the same as you I want my lines to match and look uniform it doesn’t matter if anyone else sees if I’ll know it’s there and every time I go out in the boat I will wonder what could I have done differently to make that line up better
@TripleRwoods
Жыл бұрын
I’ve got a “long term update” video on how it has held up over the past couple of years coming out next week. Your making the right call.
@dannyneal9713
Жыл бұрын
@@TripleRwoods that’s good to know because the last thing I need to do is for it to start fading chipping and peeling.
@bob5074
2 жыл бұрын
Why didn’t you carefully cut zig-zag between the diamonds to match up the pieces?
@TripleRwoods
2 жыл бұрын
The way it was printed the zig zag would have “leaned” to one side of the sheet. So the next sheet wouldn’t line up perfectly.
@FoodPornNetwork
3 жыл бұрын
That sucks the edges are cut bad, not cool to have to waste such an expensive material! How do you like the edge trolling motor, it has good reviews on walmarts site, but on minn kotas site they are all bad, very strange. I am wanting to get the trolling motor and the flooring as well!
@TripleRwoods
3 жыл бұрын
That one in the video is the 12v 45lb thrust I think, I actually sold it and upgraded to a 24v 70lb thrust min Kota edge and it is great. The extra thrust is a game changer. You can’t go wrong with either but if you can swing 24v I would encourage it. 👍🏻
@FoodPornNetwork
3 жыл бұрын
Did you add the fuel filter for the motor, I might add one to mine, thanks.
@TripleRwoods
3 жыл бұрын
Yes. I highly recommend a fuel filter on every motor.
@codystory7496
2 жыл бұрын
Just ordered three sheets to cover my 1860. Hope it’s enough. Didn’t know about the edges. Not trying to sound stingy but I paid $130 a sheet and I’d like to be able to use the whole sheet! Wonder why they can’t cut it straight
@TripleRwoods
2 жыл бұрын
I emailed them that same question and they never got back to me 🤷🏼♂️
@bobmaverick5160
2 жыл бұрын
I was thinking about hydro turf but if they do not answer e mails then their customer service is garbage. I will find some other decking to put in my boat. Great video and thanks for your information.
@teamdirtymoney167
2 жыл бұрын
Link to where u ordered it ?
@codystory7496
2 жыл бұрын
@@teamdirtymoney167 I also got the molded cut diamond which is more expensive than their regular lined. You can see all their options on website
@teamdirtymoney167
2 жыл бұрын
@@codystory7496 what’s there website ?
@jtee9548
3 жыл бұрын
Hi, you made a bit of a mistake Sir, when using the Weldwood contact cement. It is applied to both surfaces and allowed to tack or dry. You have about a half hour to two hours work time (out of the sun at room temp) then you're screwed 😁. After the two surfaces tack up you have one try, remember, it is CONTACT cement, when it touches it's glued! You can place wooden dowels on the deck as spacers between the Hydroturf & the deck once the glue is dried (after about a half hour) then you eyeball it, start at one edge and work your way across the panel, pulling the dowels as you go. Once it's down you can use a cheap J-roller to press the Hydroturf hard against the panel for great even contact. You glue a little bit at a time, starting at one edge with the dowels, or a friend (dowels are better) keeping the two surfaces apart till you've got it just right, you go from one edge & work your way across to avoid ripples & the dreaded bubbles. Wooden dowels & j-rollers are cheap at Lowe's, Home Depot etc..... Also it would seem that the expansion/contraction of the product might be a problem with seasonal temperature change, the glue has stretchy neoprene in it, but I don't think it's gonna stretch enough. I hope everything works out ok.
@TripleRwoods
3 жыл бұрын
I’ve seen other people do the contact cement on both sides. This seemed to work without too much trouble. You still had some time to get it positioned before it locked in. I’ve had a few spots I’ve had to re-glue but not bad. It’s holding up well so far. Thanks for the info.
@chrispeterson1247
6 ай бұрын
get the camo pattern you cant even see the seems
@tdwz1652
10 ай бұрын
not impressed with that diamond pattern though my OCD would go crazy with those seams not lining up. how it expands and contracts that much is insane too. over all you did good though man nice job
@TripleRwoods
10 ай бұрын
Thank you 👊🏻
@FoodPornNetwork
3 жыл бұрын
Wow after watching more, they obviously stamped that design crooked on the material, or it was just cut crooked from a huge piece, either way that is piss poor and they should refund you and send you new stuff! Did you get it off Ebay or direct from them?
@TripleRwoods
3 жыл бұрын
I emailed hydroturf about it and they never responded. 🤷🏼♂️. A buddy of mine ordered the $60 a sheet fake hydroturf off amazon and he loves it and it looks great.
@FoodPornNetwork
3 жыл бұрын
@@TripleRwoods Bastards lol I might go with a different brand, thanks for the info
@FoodPornNetwork
3 жыл бұрын
@@TripleRwoods I just ordered the blackttip one from amazon, thanks for saving me $ and headaches!
@jamesw5373
Жыл бұрын
Not getting the attraction to foam on boat decks. Element exposure can't be good and tearing it out a cluster.
@markela1313
2 жыл бұрын
When u get cheap stuff n they like this ok , I guess. Getting expensive stuff n it's no good, I would return it, or get half priced, it's bad business. Good luck with ur boat. I'm planning to do carpet now, because of this. I got a 1990 alumacraft super bandit, got it killer deal on it. Trying to rebuild it, to oem. Have fun
@TripleRwoods
2 жыл бұрын
I emailed them with pictures and they never replied.
@TripleRwoods
2 жыл бұрын
Good luck on ur boat project. Sounds like fun.
@ryangotsch3670
Жыл бұрын
Why on earth would you NOT Back butter the turf before laying it down?!?!
@kyletaylor8888
2 жыл бұрын
What kind of contact cement did you use
@TripleRwoods
2 жыл бұрын
At 26:47 I hold up the can I used. It’s DAP brand I believe
Пікірлер: 65