I’ve seen other videos suggesting to cut off the stair nose on each tread rather than build out the riser. This would solve the unevenness you will get at the top of the stairs.
@ChantalBoutros
10 жыл бұрын
If you're installing carpet at the top level, the carpet would wrap around the top nose only. If you're installing HW on the top level, you would use the appropriate stairnosing for your floor. Be aware that it will have a different profile from the ReTread as there's no cove molding pre-attached to stairnosing. You can always attach a separate piece of cove molding to make the look more consistant (which Stairtek also sells), but it may not match 100% to the ReTread profile.
@dhtango
6 жыл бұрын
agree with Charles. expansion will be tough with a tread that is nailed and glued down.
@zarchy55
10 жыл бұрын
I'm in the middle of one of these projects now and it is going well, although I started off on the wrong foot. I started with poplar risers painted white, both because I like the look and because it is way cheaper than the prefinished oak risers. After doing a couple of steps I realized it is near impossible to walk down the steps without leaving scuff marks on the painted risers. So I stopped after two steps and ordered the oak risers. Much better. Now I have to figure out how to pull up the two steps that I started with. That construction adhesive is tough stuff. An expensive mistake. In any case, I am very happy with the product and it will look very nice when it's done.
@Azazelilluminati84
4 жыл бұрын
U can buy the sticker that looks like oak for the risers
@bernardochaparro3794
5 жыл бұрын
I always cut the nose of thw old steps , yes its a little more work but I think it works better ,skillsaw and the cutting edge tool and u good to go.
@aferditamurtishi1488
5 жыл бұрын
I have been whatching a few of this videos and noticed that none of this guys talk about the the difference in riser hight changes on the first and last riser, or do they assume that everyone is doing new floors when they retread their stairs.
@CENTAUR559
8 жыл бұрын
What did you use for the risers? Melamine or what material and where did you get it?
@robertpowers1297
2 жыл бұрын
Would it better to measure n cut everything first and then applying stain and polyurethane before final installation?
@paulschultz3278
11 жыл бұрын
my project
@bill3641
4 жыл бұрын
He glued the risers to backing strips that weren't glued ?
@SinnerSince1962
2 жыл бұрын
Yep. Pretty dumb, huh?
@dcisfun
11 жыл бұрын
exactly how do you finish the top??????????
@rameshwariar673
10 күн бұрын
I am planning this install (DIY) using the product from Home Depot. Is an expansion gap needed for the tread and riser? Can I use a circular saw with guides for the cuts?
@markmasengale890
10 жыл бұрын
i don't get it. Is stairtek selling the measuring tool? Everything else just looks like what an experienced carpenter or DIYer would do with normal materials and tools.
@edwardburkhalter1481
11 жыл бұрын
So how do you finish the top of the stairs?
@joeqiao6843
9 жыл бұрын
how to get this special thickness wood?
@jimmychow4917
2 жыл бұрын
exactly how do you finish the top? All video they never show.
@charlesnelson8071
7 жыл бұрын
Why rip the tread 1/4" short for expansion if you nail the tread down along that same edge?
@leovbernardo
7 жыл бұрын
Charles Nelson excellent question!
@sterlingwalter6225
6 жыл бұрын
the thin alum nails will not prevent expansion
@Cliflyri
6 жыл бұрын
exactly the question I scrolled down here to pose....
@walterhoward6000
Жыл бұрын
What about one end of stair being open?
@AnthonyDavis-iz4is
2 жыл бұрын
I wish I could get long shims he used in this video
@chainz691
2 жыл бұрын
i used to work for stairtek the management team is crap but the product was good
@sterlingwalter6225
6 жыл бұрын
scabs. and no doubt this product is made from composite, ...
@crazedspidermonkey
6 жыл бұрын
I'm in the market to get stairs, when you ordered yours from Stairtek, did they come in composite?
@shannonland1137
2 жыл бұрын
can i do this over carpet
@AnthonyDavis-iz4is
2 жыл бұрын
No
@davyscales7732
6 жыл бұрын
Liquid nails yet again
@crazedspidermonkey
6 жыл бұрын
Where on the white label did you see that?
@SinnerSince1962
2 жыл бұрын
This is NOT the way to put stair overlays on. Cutting the nose off first is much better.
@sharonmaurer4423
6 жыл бұрын
EZTREAD OFFERS BETTER PRODUCT
@crazedspidermonkey
6 жыл бұрын
I'm simply asking around to all of these threaders here, because i'm in the market for stairs. When you bought your ezthread product and stairtek product, what quality differences could you see in between the two live samples?
@ChantalBoutros
10 жыл бұрын
If you're installing carpet at the top level, the carpet would wrap around the top nose only. If you're installing HW on the top level, you would use the appropriate stairnosing for your floor. Be aware that it will have a different profile from the ReTread as there's no cove molding pre-attached to stairnosing. You can always attach a separate piece of cove molding to make the look more consistant (which Stairtek also sells), but it may not match 100% to the ReTread profile.
Пікірлер: 38