I think the installing return air duct show was great I learned a lot.
@KeithFox
10 жыл бұрын
"How to use a circle cutter and not reference the next video/finish the current video" It started out great then just kind of drifted off... if there is a part two to this, I can't seem to find it.
@phildavis5377
11 жыл бұрын
You really should wear safety glasses when using the circle cutter. Ear plugs wouldn't hurt either. I've been sheet metal mechanic for over 30 years I know. Lesson learned.
@HansyPants184
4 жыл бұрын
30 years in and the tin-basher still has to watch KZitem videos on how to do his job! Typical. But hey, at least he isn't bothering the carpenters for instructions anymore. Lol. Seriously though, great points. Wear your PPE!
@pexto8003
9 жыл бұрын
Good job, yes on some glasses, no to gloves. Sheetmetal guys dont usually wear gloves.
@sketterman10
10 жыл бұрын
Where is the rest of the video?
@WesHamstra
8 жыл бұрын
where did you get that circle cutting jig?
@Balticblue93
Жыл бұрын
What is the purpose of this duct? Where is the air coming from and and where is it going? You should have used an elbow that has the foam and mastic adhesive plus four short sheet metal screws. You just created turbulence and upset the airflow which causes air friction and slows down the CFM's and gives a place to catch dust, lint and crap in the air.
@quitefar03
Жыл бұрын
this has been a great video. i have question which I have confused about. the see that small pipe running next to the duct where you make the cut. is that not the cold air return pipe?in my case, I have the same setup of ducts, but this large one is hot which means this is a supply. hence, I am thinking this whole installation should happen on the smaller pipe (cold air return). can you pls correct me?
@Lilman3000
2 ай бұрын
How is one duct effective in any house?
@Chewy_GarageBandDad
Жыл бұрын
Is this a 2 part vid? Did you use a filter and did you cap the hole
@eugenebell83
10 жыл бұрын
That is a good way to lose an eye failing to wear safety glasses.
@-mejor-que-nostradamus-6152
3 жыл бұрын
My Friend Can You Tell Me What Type Of Drill Bit Did You Use ..... I wanna Buy Same Drill Bit Please Brans And Size.....Thank You For Your Video.
@bradbrizzle658
4 жыл бұрын
Some of the flanges should be bent to be on the outside of the duct you are attaching to I believe
@Balticblue93
Жыл бұрын
Wrong type of take-off duct to be using period for the purpose. Should be the stick on with the gasket, use the caulking gun style mastic then four self-taping screws. The metal has to be flat or it will catch dirt and crap plus cause turbulence and air disturbance in the duct. This will actually reduce the CFM's. I just do not see the purpose of adding that 90 to be "adding return air duct". Where is the air from and where is it going? The video stops so suddenly. No sealing of the elbow before it just stops.
@dennyblazer1167
5 жыл бұрын
If you straighten out the elbow it will be easier
@me84mo1
4 жыл бұрын
How to know where the return air place in basement
@azhkell
3 жыл бұрын
for those looking for the rest of the video kzitem.info/door/UUfEJFjX8iJuedWJWbGxcbiQ
@robertonic100
12 жыл бұрын
esta es buena herramienta
@ChronicKPOP
11 жыл бұрын
I noticed, I had a friend that got a fragment of non magnetic metal in his eye, not fun. Especially on a how to vid... safety 1st
@triggerwarning4746
2 жыл бұрын
What’s the name of that circle cuttin tool?
@greenharvestproductions6743
8 жыл бұрын
question what do you have to seal that new intake
@therontheodore6822
7 жыл бұрын
Jose Velez same question😂
@simbalage22
14 жыл бұрын
What is the purpose of the cold air return.. What if you installed a furnace without one? Just let it get the air from basement?
@Vincegould
2 жыл бұрын
Hot air rises and fills the rooms upstairs. The return down in the basement doesn’t grab that hot air
@andypies01
12 жыл бұрын
Hey What is the circle cuuting tool called please Great vid
@CMchannel824
2 жыл бұрын
Question. I have a toilet that I’d like to relocate but there is a return air duct in the new location. Can I cut a hole in the return air duct and run a pipe through it and then seal it with tape?
@Balticblue93
Жыл бұрын
Not if you want things to stay up to any sort of code regulation, no. You do not put a pipe through a duct line.
@hurst2385
8 жыл бұрын
it would have been alot easier to push the flanges down it that elbow was straight.
@deb4tune
14 жыл бұрын
see the rest of the videos to complete this installation at DonMartinHVAC youtube channel
@Agenda21Truth1
4 жыл бұрын
Debra Braun why don't you post a link?
@hangngoaigiare
4 жыл бұрын
Where r u still allow panning
@SteveBiley
8 жыл бұрын
Is there a second video??
@stasvladimer8071
3 жыл бұрын
What’s the name of this toolb
@gregpruitt1647
10 жыл бұрын
Where can I get a circle cutting tool?
@kajehugh
12 жыл бұрын
if u dont have cold air return the ocld air just stays upstiars so in the winter months its very cold upstairs without one
@goosecouple
7 жыл бұрын
Against code to use the joists as return air plenum.
@LoopBak127
6 жыл бұрын
Not in all locations. It was put in my home by the builders and passed inspection.
@sonnydash4987
6 ай бұрын
In an exterior wall is a no no.
@kwiktips
12 жыл бұрын
Use gloves and you won't have to worry about cutting your hands.
@benpustina3224
7 жыл бұрын
nice flimsy return panning.
@clevelandgreg1027
3 жыл бұрын
this is not how to install an air return. and not the first step. you should always start with your opening and work your way back...
@carmelom269
3 жыл бұрын
🤷♀️ No mastic or tape to air tight seal the new return fitting. 🤦♀️ Looks like the same sloppy work that was done by the knucklehead amateur HVAC contractors that installed the HVAC system in my newly constructed 4br/3bth house back in 1999. If the HVAC contractor fails to seal with a mastic and tape he/she needs to be fired and not paid.
@Chickennss
Жыл бұрын
Holy sht bro. Please wear glasses.
@nicksavage2401
7 жыл бұрын
And he got fired...
@SayNEthngLoseUrrthng
13 жыл бұрын
A six inch return, really and what is a hundred cfm's really going to do..... IJS
@metaltera86
9 жыл бұрын
Why didnt you just straighten the elbow first then move the tabs. Its easier to reach your arm in that way lol
@kylebjerke9936
5 жыл бұрын
He didn't seem to have any trouble. Get off his nuts.
Пікірлер: 49