That…music…made me…..go…..insane. Now I can’t get it outa my head😮.
@SCWJackE
4 жыл бұрын
Perfect!! Thank you, great job of explaining this. Now I just need to understand how to spec the male threaded stud to the female threaded insert.
@allens7476
5 жыл бұрын
I was taught that the slot goes in first. I use a 6" piece of threaded rod with two nuts to start the inserts. Easy to keep it perpendicular to the work. BTW, I've never had luck with the stop collars. They're never perfect for the bit so they wiggle, and tend to come loose. I use a piece of tape on the bit.
@SlabGuy
5 жыл бұрын
The slots index the install tool, at least the inserts I’m using.
@allens7476
5 жыл бұрын
@@SlabGuy I saw that! I've never seen that tool before, cool device!!! I used a screwdriver in the slots until someone told me I was doing it wrong! The threaded rod is handy because it allows you to easily see it's going in perpendicular to the work. Two nuts lock against each other and push the insert in.
@iSin_
4 жыл бұрын
I am building a wooden table from scratch tomorrow and this video looks very helpful! What kind of drill bit do you use? I see you have a box of different sizes.
@asd67lkj
3 жыл бұрын
Added a like for the tip on using the collar from the Kreg jig......
@instantalbums
Жыл бұрын
Hey mate - how much smaller should the drill hole be than the insert so it holds in tight? Also I guess with slab timber you don't have to worry about movement?
@UncommonS3nse
4 жыл бұрын
Total novice here. I'm thinking of installing some inserts in my desk and wonder if there is any rule of thumb as to how far into the wood you can safely go with the inserts? (my desk is only slightly over 1" thick). Also, would there be any value in using a small amount of adhesive before fitting the inserts?
@SlabGuy
4 жыл бұрын
I wouldn’t use an insert longer than 5/8” long. And be very careful drilling. I’d practice on a test piece first. I don’t use any glue in case the insert ever needs to come out.
@MeMe-qi6ph
10 ай бұрын
What bit did you use on to drill to attach to bolt with threads?
@dede6110
2 жыл бұрын
where i found this inserts and bolt? home depot doesnt have any good one
@1959Berre
5 жыл бұрын
Did you think about the wood shrink? The slab will crack if you do not allow it to move for at least 1/2' for every 2 feet of width.
@marcelinanoss8825
4 жыл бұрын
you can also add some epoxy on the threads to make it more permanaent
@jasondbaker
4 жыл бұрын
The holes in the metal base of the legs should be slotted to allow for wood movement.
@craighewison1738
4 жыл бұрын
What is the benifit to using this method over normal screws please? I'm currently making my first table so am quite naive
@SlabGuy
4 жыл бұрын
I prefer using these for a couple reasons. The main one being that the hardware can be taken out many times without compromising the wood. If you ever have to move the table, it’s a big help.Second reason is appearance. It looks like a nicer final product. They aren’t expensive and are very easy to install.
@jiahui288
2 жыл бұрын
Hi for the hole how can I know how depth should I drill? Pls advice if anyone knows tq emergency use🙏🏻🙏🏻
@Vinylrebel72
4 жыл бұрын
Can’t see anything...
@backnine39
5 жыл бұрын
what drill bit did you use to screw the insert?
@SlabGuy
5 жыл бұрын
Standard wood/metal drill bit, nothing special. The sizes vary based on the insert.
@backnine39
5 жыл бұрын
@@SlabGuy thx. As u can tell I'm pretty new to this.
@SlabGuy
5 жыл бұрын
No problem at all, we were all new at some point.
@TheFalconJetDriver
5 жыл бұрын
The hole needs to be the diameter of barrel of the insert, if you can not measure the diameter or do not know the diameter of the barrel. Hold up several drill bits with a light behind the insert. You want the drill bit to hide the barrel but still be able to see the flutes (ridges) extending beyond drill bit. I hope this helps.
@allens7476
5 жыл бұрын
It depends on how hard the wood is. Start with one about the size of the insert body (minus the threads) If it goes in with difficulty, go a little bigger. I've split some poplar trying to force an insert in too tightly.
@michelleperkins7797
3 жыл бұрын
Thanks for the video, do threaded inserts allow for wood movement? I've seen lots of things saying you shouldn't screw the legs directly into the top due to seasonal movement, but wondered if these pieces of hardware reduce that? Thanks in advance.
@SlabGuy
3 жыл бұрын
They don’t allow for movement on their own. They are preferred over just screwing straight into the wood because the fasteners can be taken in and out with out damaging the wood.
@joslinnick
4 жыл бұрын
The wort thing ever is when the stop collar slips.
@iandunn206
3 жыл бұрын
What was the benefit of drilling the starter hole at 1:20, then switching to the second bit at 2:01 ?
@SlabGuy
3 жыл бұрын
I do that so the larger bit doesn’t walk around. I’m drilling these with a hand drill, and they need to be fairly accurate.
@iandunn206
3 жыл бұрын
@@SlabGuy ah, that makes sense, thanks!
@ashkengaming1149
Жыл бұрын
What the size threaded nut
@OPSteel97
5 ай бұрын
Shouldn’t you put some wood glue on those inserts?
@harrowlax28
6 жыл бұрын
If the bolts are are fully tightened onto the leg bracket, why don't the threaded inserts come out when going to remove bolts?
@russell3421
6 жыл бұрын
Steve Ward the insert’s shape doesn’t allow it to spin backwards
@timetravellingbunny3952
5 жыл бұрын
Steve Ward - The inserts are installed with more torque into the wood, and would require more torque to remove from the wood, than is required to remove a screw or bolt from the internal threads of the insert. Russell - The special driver bit (possibly from EZLok) used at 3:50 to install these inserts will just as easily remove them. Nothing in the design of the inserts disallows them from spinning backwards.
@eddieed_2328
3 жыл бұрын
do you use epoxy on the threaded inserts?
@nathanortega2074
6 жыл бұрын
Im planning to the same, but instead of a metal leg im using wood. Just wanted to know how have they held up with normal use of the table
@SlabGuy
6 жыл бұрын
No problems so far. The only issue I have ever run into with these is installing them into end grain. In softer woods they do not hold as well, in hardwoods, it is generally better but can vary also.
@nathanortega2074
6 жыл бұрын
Second Life Design thank you for your much needed insight.
@MirceaD28
6 жыл бұрын
Do they work on HPL?
@Jeremy-su3xy
6 жыл бұрын
I'm gonna insert 8mm bolts not screws. Are there the right insert nuts for my application?
@bohhica1
3 жыл бұрын
As long as the threads are the same yes, you can tighten a bolt more tighter.
@wandakowalski7063
3 жыл бұрын
Appreciate the effort but it would have been a better video if you described the sizes of how deep the first pilot hole was and the size of bit you used and then the size of the second bit. And what kind of bolt or screw did you use???? And how were the legs attached? Not much to learn here and it was hard to see and that music in the background is useless and unnecessary. Just saying ...
@WTCheatShaming
3 жыл бұрын
Where do I get leggings like that?
@ConnorMulcahey0
3 жыл бұрын
Lots of options on Etsy. TheLegShoppe is a good seller, for example
@mucsalto8377
5 жыл бұрын
that is a nice instruction how not to do this in a professional way. The insert is put in the wrong way, the slot goes in first!
@SlabGuy
5 жыл бұрын
The drive tool engages into the slot. I was following the instructions provided.
@mucsalto8377
5 жыл бұрын
@@SlabGuy CHECK THIS OUT. kzitem.info/news/bejne/1X-eq6WlhHdpd5g
@justincody9972
5 жыл бұрын
it seems everyone is correct here (www.groov-pin.com/tap-lok-wood-series.html). I was seeing different suggestions and hit upon an actual manufacturer site that recommends either way depending on the wood (slotted-end down for medium-hard woods, up for softer).
@elguarogozon1
4 жыл бұрын
kzitem.info/news/bejne/saGCv4aNp32ka2U
@53C52
3 жыл бұрын
@@mucsalto8377 The guy in the video you linked says the purpose of the slot is to cut wood, then says you should first drill a hole to match the outer diameter of the insert. What would be the point of having slots designed to cut when inserting those slots into a hole that’s already as big as the outer diameter of the slots? Those slots are for insertion tools, not for cutting wood. That’s why manufacturers of that type of insert make insertion tools that engage with those slots.
@paulalderson6920
4 жыл бұрын
Do you really need background music?
@jamesthebond0072
Жыл бұрын
Does it matter really
@MrAutore
5 жыл бұрын
How does one go about doing this with metal?
@SlabGuy
5 жыл бұрын
Search for something called a Riv-Nut.
@yoheff988
4 жыл бұрын
Will those work with Plywood?
@SlabGuy
4 жыл бұрын
It depends on the thickness and quality of the plywood. They do make shorter inserts that are less than 3/4”. If it’s a lower grade plywood it can pull out pretty easily.
@johnniewilliamsjr9792
4 жыл бұрын
Singing and - talking.
@bohhica1
3 жыл бұрын
Been nice to see the close up of the whole procedure,not the finished end.👍👎🏻👍👎🏻👍👎🏻🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸
@MrKen-wy5dk
3 жыл бұрын
Please kill that silly royalty free repetitive background music. You don't need it. I stopped watching after 3 minutes when the ice cream truck never came. No thumbs down, but no up, either.
@hammondmiers3789
3 жыл бұрын
I did it too. This is what I used Stodoys designs for
Пікірлер: 67