Love the videos I don’t even have a 12v at the moment but will eventually come back to watch the video again when I do.
@Hazardous-Hotrod-Knowledge
Жыл бұрын
Glad to be a bad influence in your potential next purchase 🤣 start looking, they aren’t getting any cheaper!
@darius9521
Жыл бұрын
Thanks for the video! Makes me wanna go install my dv's and gsk that I've had sitting in the basement for over a year. A video on pump timing would be awesome
@Hazardous-Hotrod-Knowledge
Жыл бұрын
I'll get on a pump timing video, I have a hillbilly way of doing it where you dont need any special tools and it can be done in minutes!
@Adam-2003
19 күн бұрын
Extremely informative video thank you sir, when I did my Governor Springs earlier today I noticed that I only had a single shim on one spring set inside my pump and nothing on the other side... hoping this is normal as now I'm worried that i might have lost one in the pump! Not talking about the idle spring shims and the big plate at the bottom of everything as those were both present and identical on each side but the shim(s) for the smaller inner springs to which I only had one in one stack and none in the other. Thanks!
@josephthomas4783
Жыл бұрын
Awesome video! Try to warranty your bluepoint socket. Mine has always fit nicely on every truck I’ve used it on.
@Hazardous-Hotrod-Knowledge
Жыл бұрын
Good idea! Maybe I got a faulty one, I’ll see if I can get in contact with a snap on dealer
@JoeyDavidson-qb6ke
Жыл бұрын
Great video, im doing injectors on my 1997 12v &i have alot of great input. Ty
@haydenwilliams1750
Жыл бұрын
Great video mate!
@misterj5045
10 ай бұрын
I've used a torx socket on my tamper proof screw. I think it was a 25 or 27. Set it centered with an extension and a few taps with a ball peen hammer to give it bite.
@Hazardous-Hotrod-Knowledge
9 ай бұрын
I’ll have to give that a try! Sometimes there’s a little dot in the centre of the tamper proof screw, I imagine that’s what you’re hammering into
@misterj5045
9 ай бұрын
@Hazardous-Hotrod-Knowledge Yes, it has a small indent on the top so when I tap the torx in, it is able to make its own shape, plus I think the shock helps loosen the bite before trying to turn it. I believe it is a 25 or 27 on the top and 20 on the smaller afc housing back plate. I reuse the same fastener once doing this.
@PnwTinkerer
Жыл бұрын
Great video !! Thank you
@michaeldixon908
6 ай бұрын
Nicely explained. Thanks
@Hazardous-Hotrod-Knowledge
6 ай бұрын
Glad it was helpful! Thanks for the comment :)
@EspososRivera-Chavez
11 ай бұрын
SOS otro rollo amigo muy buen bideo😮
@Hazardous-Hotrod-Knowledge
11 ай бұрын
Thanks!
@Jeff-vc2tt
Жыл бұрын
Power driven diesel makes a socket for the delivery valves
@Hazardous-Hotrod-Knowledge
Жыл бұрын
One guy suggested to get it warrantied, so I’ll try that and if it’s still junk I’ll pick up one of theirs!
@Jeff-vc2tt
Жыл бұрын
@@Hazardous-Hotrod-Knowledge yeah they're awesome specially made for delivery valves
@Nicksvintageiron
9 ай бұрын
What are your favorite brand of governor springs youve used? Ive had a bad experience with one brand and would like to swap mine out
@Hazardous-Hotrod-Knowledge
9 ай бұрын
Ive used “handytek” Amazon 4k gov springs in more applications than I can count and have never had a single issue. What trouble have you been having?
@Nicksvintageiron
9 ай бұрын
I used a set of DAP springs in one truck and they were super touchy. Almoat felt like 5k springs. I've adjusted them multiple times and still can't get them how I want them. The other 2 trucks I've done I've used cheap ones with decent luck.
@shevilihabibi8895
Жыл бұрын
please tell me, how much horsepower did you get after these improvements?
@Hazardous-Hotrod-Knowledge
Жыл бұрын
I set up the AFC housing pretty mild but typically a truck with these mods on the stock turbo will go to about 350hp
@rockycourtney3110
Жыл бұрын
Can you take the copper washer out from under a 175 horse pump delivery valve to make it like a 215 horse?
@Hazardous-Hotrod-Knowledge
Жыл бұрын
It’s more than that for the differences between the pumps. The 180 and 215 Hp injection pumps have a completely different pump cam that delivers fuel at a faster rate, as well as having a better plunger design. The copper washer is just a different sort of thing they did with the barrels in the 160/175 pumps to seal the delivery valves and was done away with the later pumps
@rockycourtney3110
Жыл бұрын
@Hazardous-Hotrod-Knowledge Thanks for the reply I did some research and found out the same , I am bummed because my engine was built as a high output with a 215 pump, but a shop replaced the pump with 175 horse yrs ago .
@DiegoSepulveda-dz3vs
9 ай бұрын
Alguien puede traducir
@Hazardous-Hotrod-Knowledge
9 ай бұрын
No estoy seguro de cómo traducir al español y puede ser mucho trabajo con todos los subtextos que tengo en el video también. Gracias por ver y estar interesado en el video, espero que de alguna manera puedas disfrutarlo :) Utilicé un traductor en línea para esto, solo puedo hablar inglés.
Пікірлер: 30