Installing a Summit Racing dual plane intake manifold on a small block chevy with vortec heads. Intake part number: SUM-226018 Gaskets part number: FEL-1255
hello I would like to replace the chevy van 3500 gasoline engine year 2000 with a diesel engine, can you refer me to a diesel engine model that can work on the van please.
@Rhawk03
3 жыл бұрын
I’m putting vortec heads on right now! Thanks for the info!
@Vanchero1955
Жыл бұрын
How's this engine holding up?
@iowadiy6361
Жыл бұрын
So far so good!
@Snailmailtrucker
3 жыл бұрын
I just installed my Intake Manifold on my Vortec head 350 062 heads. What are the 2 - 3/16 holes in the Intake Manifold on your driver's side for ? (2:37 mark in your video) ? They go all the way into the Valley and I have no idea what they are for.
@iowadiy6361
3 жыл бұрын
I’m pretty sure that those are actually blind holes (not through to the valley) and are for mounting throttle linkage
@lad63bird
2 жыл бұрын
Also i never retorque bolts that are siliconed because you break the seal and can have leaks....
@dewaynebanks5369
Жыл бұрын
Which intake fits a 2000 s10 4.3 vortec
@lad63bird
2 жыл бұрын
I Put silicone on every bolt so they all torque the same. Regardless of them invading into a water jacket you want consistency on torque spec and a siliconed bolt will act very differently than a dry bolt..
@iowadiy6361
2 жыл бұрын
That’s a good thought! I should probably use that technique as well!
@darrellsomers5427
Жыл бұрын
If GM didn't use silicone you don't need too I didn't and I have no leaks ,if any thing it will screw with the true torque setting
@Posibrian
Жыл бұрын
@@darrellsomers5427There are torque specs for wet or dry bolts. I suggest anaerobic Permatex in red.
@mariomoscaritolo636
8 ай бұрын
use a loctite blue for sealing
@johnnywrench5579
3 жыл бұрын
A BLIND hole is closed at the end.
@iowadiy6361
3 жыл бұрын
Correct. I might have said that backwards
@wildwillscustomsexhaustvid9677
2 жыл бұрын
What bolts did you use. Also are the ports for heater core hoses?
@iowadiy6361
2 жыл бұрын
I used an intake bolt kit from the auto parts store. The ports could be used for heater core hoses or also could be for bypass lines (only needed for racing or extreme temps)
@wildwillscustomsexhaustvid9677
2 жыл бұрын
Awesome thanks
@adancortes3568
3 жыл бұрын
do these intake manifolds fit on 97 5.7 vortec ?
@iowadiy6361
3 жыл бұрын
Yes it is designed to work with vortec heads
@riccjames6514
3 жыл бұрын
Wut the part # for that intake Manifold from summit
@iowadiy6361
3 жыл бұрын
It’s SUM-226018
@Tacuache602
3 жыл бұрын
Do you have a part number for the gaskets
@iowadiy6361
3 жыл бұрын
I believe I used fel-pro gaskets. The PN for Summit Racing is FEL-1255
@bobsilver3983
2 жыл бұрын
Only 15 foot pounds?
@iowadiy6361
2 жыл бұрын
It sounds low, but that’s the spec for it
@Snailmailtrucker
3 жыл бұрын
Nice job Liked/Subscribed
@buckwall8410
2 жыл бұрын
Felpro has a metal core that one doesn't
@iowadiy6361
2 жыл бұрын
Good to know! I'll keep that in mind for future use
Пікірлер: 29