I thought there might be some interest in this. Its actually my 13 year old daughters design. I'm more the OH&S and supervisor :) I'll see what I can bring together.
@H220RMS
Ай бұрын
@@smart_home_australia i think it would be good content that would fit into smart homes quite well!
@smart_home_australia
Ай бұрын
Now I just need to convince my daughter to let me borrow her beloved school projects for a few hours, she's very proud of it :)
@andrewpowell2035
Ай бұрын
FYI There is also a Mqtt connector for those running Victron gear through a network connected Cerbo gx (or raspberry pi)… I will try this out as well as the Bluetooth connection for the smart shunt and the individual mppt’s is potentially easier….
@smart_home_australia
Ай бұрын
Thanks Andrew. I don’t have the Cerbo GX, but if I get one I’ll definitely test it out. Thanks for letting us know. 👍
@skm7812
Ай бұрын
Awesome, it worked!!! Clear and step by step instructions. Thank you for sharing. (from Seattle)
@smart_home_australia
Ай бұрын
You're most welcome Seattle :) from Sydney :)
@hydeapd
Ай бұрын
I would like to see the power bank and solar charger set up.
@smart_home_australia
Ай бұрын
Thanks, I'm lining up a video for this. Although it will be a retrospective as I did the project with my daughter some time ago for fun. But since there is so much interest in it, I'll do it :)
@michaelklaussner8193
Ай бұрын
Is it possible to connect to more than one victron device with just one esp. And will victron smart networking over bluetooth still work. For exmple i have one victron mppt, one smart Battery watch, and one smart shunt, witch are actually conneted by victron smart networking.
@smart_home_australia
Ай бұрын
Hi Michael, this was a proof of concept for me, so currently I only have the smart shunt in place, but I'm planning to introduce the smart solar controller. The documentation lists in its configuration multiple devices, so I don't see why not. And besides, for $10 give it a try and let us know how you go.
@florianosabatini4016
Ай бұрын
Hi, it would work to detect when my UPS is about to power off so that I could create an automation to shut down my NAS. My initial idea involves using the ESP32 along with a voltage divider connected to the 12-volt batteries of my UPS. But now I wonder if Victron could work as well
@smart_home_australia
Ай бұрын
Thats an interesting user case. Doesn't your UPS has a SNMP message that the NAS can read direct? If not, then yes you could use this for that usercase.
@H220RMS
Ай бұрын
Maybe have a look at a NUT setup, thats what i have done with my NAS (old readynas, hard to work with)
@florianosabatini4016
Ай бұрын
@@H220RMS my low cost UPS has no communication ports so no way to connect to NUT
@florianosabatini4016
Ай бұрын
@@smart_home_australia No, it is a basic NAS with no communication ports
@smart_home_australia
Ай бұрын
in which case it might be a Victron Shunt and a Switchbot FingerBot, with some HA automation magic :)
@DominicShooter
18 күн бұрын
⚠Please note if you take a screenshot of your encryption key from the victron app that it cuts off the first character of the key.
@smart_home_australia
18 күн бұрын
Thanks, sounds like you found out the hard way??
@carsandtools
2 күн бұрын
It took screenshot of the whole thing to me (iPhone).
@smart_home_australia
2 күн бұрын
@@carsandtools NIce... it did for me also... but I guess not all keys are the same length.
Пікірлер: 22