For everyone whos checking out this project, be aware of the following: 1.The code used in the linked webpage is masking APPARENT POWER into REAL POWER and thats completely wrong. 2. Whats worse is that the energy calculation in the code takes apparent power as real power sooo guess what? the energy calculation is also wrong. 3. The ZMPT module introduces a phase shift in the voltage signal. This is because on the secondary side the signal is fed into an amplifier. This doesnt affect RMS voltage readings at all but it completely screws up the REAL POWER calculation. Im not saying this is a bad project at all, it works pretty well to get VRMS,IRMS and Apparent Power readings however forget about calculating real power, power factor and energy because as I said earlier, this is screwed up by the ZMPT module itself.. You may try to correct that phase shift by software but I cant guarantee you will get decent accuracy in the readings. If you want to calculate real power then you should use a crude step-down transformer.
@supercorn5607
4 ай бұрын
but are the connections correct?
@angelhuerta4559
4 ай бұрын
@@supercorn5607 Yes the schematic shown in the video is correct
@mohamedsyahiran9857
16 күн бұрын
@@angelhuerta4559 So youre saying that it only works virtually? if done physically?
@MrAlsan
Жыл бұрын
This is Awesome project 👍
@mehmoodrec
Жыл бұрын
hi nice project but can we configure it to read power and energy in bidirectional mode.
@srikumarc
10 ай бұрын
Can you make the same project for 3 phase power monitoring?
@binisol7353
7 ай бұрын
Nice One but whats the Capacitor voltage you used cause it only shows the 10uf on the circuit???
@sujalsirvi4681
Ай бұрын
I done this project successful 😀
@mohamedsyahiran9857
16 күн бұрын
Can you share the easyeda schematic?
@davidcromapix9083
5 ай бұрын
Thanks for sharing
@0124akash
4 ай бұрын
Wifi connected nahi hoga to LCD me parameters nahi show honge.
@juandanielvelezmunoz2667
Жыл бұрын
how is it , with three phases,? that is to say with 3 three current sensors and three voltage
@MauriceArwa
Жыл бұрын
let's assume the wifi is faulty but there is power, does it have local (Offline Storage) that can be used during this time, so that when the wifi is back on it just syncs up? or does it just resume from where it lost connection?
@beastscientist
Жыл бұрын
yes the esp32 is having the eeprom of 512bytes so it can also save things
@vedanthlahoti3741
9 ай бұрын
Can you share where did you make circuit simulation
@yougetchandan
10 ай бұрын
A fatal error occurred: Failed to connect to ESP32: No serial data received.
@Suryaa11105
9 ай бұрын
Did you resolve it?
@yougetchandan
9 ай бұрын
@@Suryaa11105 i used another laptop...and i didn't face the issue 🙂
@Suryaa11105
9 ай бұрын
@@yougetchandan is this working properly or did you face any issues..
@arinjain2671
5 ай бұрын
Driver issue
@bayazidkhanburki4158
6 ай бұрын
Can we add the a module of showing a real time price occuring while using the power electricity
@HowtoElectronics
6 ай бұрын
Check the latest video. Its there.
@asyraafazhan136
6 ай бұрын
do you mind sharing the pub design for this 2.0 version
@inuzuka_6934
11 ай бұрын
Uhm what are the jumper cables did u use??
@sidharthsharma1008
Жыл бұрын
can we use ACS712 current sensor?
@rauloliveira50
Жыл бұрын
Did you it ? I'm trying here but I failed
@MANOJ_BHASKAR_
7 ай бұрын
Hie sir/ma'am Ur work is too good I need help from ur side ma'am From last one month I trying to connect esp32/esp8266 to blynk but it is not connecting but it is connecting to wifi so please help me out Monday I will be having project review
@sajinraj-jy3rf
Жыл бұрын
Sir, to measure the voltage of each device connected to nodemcuesp8266 is possible ?
@beastscientist
Жыл бұрын
yes buyt it is costly
@Engineerswarup
Жыл бұрын
Pls tell us that how to connect blynk app after 4 virtual variable pin set and code to get output
@beastscientist
Жыл бұрын
get the blink authiticating code
@Radioknowhow-if7mz
3 ай бұрын
hello guys i just build this project but i got some confusion when i add blynk function my serial monitor print zero but when i remove all the blynk function it read voltage and current all good where did i do wrong guys ....the issue is when i add blynk to send those data to blynk app it print all zero value but when i only do without blynk it work fine... any help guys i just stack here
@008sarathkismatwaale5
Жыл бұрын
Mam how much maximum distance we can see parameter value mam..
@theochub
10 ай бұрын
Any where in the world if esp32 connect with wifi
@rafirabbanifirdaus5028
Жыл бұрын
Is it permissible to change the calibration factor in the code? this line I mean: #define vCalibration 200 #define currCalibration 0.50
@lavanyayerguntala8977
7 ай бұрын
How to send current measure to email use in ESP32 board
@supercorn5607
4 ай бұрын
Hello, can I please have the file for your schematic and pcb show in the video?
@ROHAN-PATIL
Жыл бұрын
its clearly not working why you are wasting other people time i made this same project it doesn't calculate apms power in your vid its clear that its not working put 10w load bulb and its not reflating in app SHOW PROOF WITH HIGH LOAD
@naveedansari9842
Жыл бұрын
i am facing an issue i compile this program and upload ESP32 ardunio module.Iused lcd 20*4 but nothing show in display of lcd . Any one suggest me
@manthangujar1030
Жыл бұрын
eepromstate(); was not declared in scope showing an error while compiling
@HowtoElectronics
Жыл бұрын
I have updated the code and fixed the issue. You can try with new code now.
@ابوحسانالهويد-ج8ض
Жыл бұрын
A circuit to prevent power pumping into the network with an on grid system
@beastscientist
Жыл бұрын
more explanation need for better asistance
@jephtah737
Жыл бұрын
ma'am can use the Emonlib to measure only voltage, i dont need the current
@beastscientist
Жыл бұрын
yes just remove the current part
@mrz2245
Жыл бұрын
hi, i need help. i only connect the esp32. but the voltage still reading at 5V. but i dont connect any voltage and current sensor
@toksgagik9111
5 ай бұрын
di you fix the problem?? i have the same issue
@shaswatsingh4656
Жыл бұрын
I am making Same project but on Home Assistant not using blynk 2.0 because of free version support max 2 devices
@beastscientist
Жыл бұрын
no you can add upto 10 devices
@sudhakars8703
Жыл бұрын
Please make an video for oxygen monitoring system for home with oxygen sensor
@HowtoElectronics
Жыл бұрын
Please share the link for buying oxygen sensor.
@beastscientist
Жыл бұрын
its easy i alreday had it
@selvaraja0147
Жыл бұрын
Mam i have esp 32 V1, but you are used V4. Will any problem come with V1?
@beastscientist
Жыл бұрын
no just change an the code
@keeeerthan
Жыл бұрын
I have doubt on the resistor value u said 10k and 100ohm but in fig 100e is there
@HowtoElectronics
Жыл бұрын
100e and 100ohm are same thing.
@beastscientist
Жыл бұрын
its 2 10k and one 22 ohm
@chennaicraft7556
Жыл бұрын
Awesome project but power is not accurate
@sifoslimeni3826
6 ай бұрын
Why is irms equal to zero?
@toksgagik9111
5 ай бұрын
di you fix the problem?? i have the same issue
@zeroman6860
11 ай бұрын
please modify the code....still it is not working...code is complied and uploaded but the result is not coming....after the power cut it is still starts from zero itself
@BhaveshbhaiSolanki-x2d
5 ай бұрын
Hello
@allinonetech9990
3 ай бұрын
How to skip iot coding part I don't want to send data to blink server. I only want data to display on display. Anyone help me .
@theochub
19 күн бұрын
yes i can
@mintamerinjacob5114
Жыл бұрын
How to power thr circuit without using usb cable
@beastscientist
Жыл бұрын
just use the power pins
@geraldosocorro1186
Жыл бұрын
Hello. I am not able to find the correct EEPROM library for the ESP32, I tried several, could you help me. Please.
@HowtoElectronics
Жыл бұрын
Hi there was minor bug in the code. I fixed it and updated few hours ago. Try the new code now, it works.
@geraldosocorro1186
Жыл бұрын
@@HowtoElectronics OK! I will test it, thank you very much. 👏
@pulendranmathi1874
Жыл бұрын
hi, So i want to display the power consumption price also, with time to time varying the unit price of Government updates. so how can i add this part in the code. please let me know. Because i want to do the project in campus. And also i want connect with this solar and want to calculate that power consumption also. So please help me
@VamshiKrishna-zh3zl
4 ай бұрын
Have you done that project bro?
@muhammadshoaib3796
8 ай бұрын
can i reset the values of KWh by just click on esp32 reset button?
@HowtoElectronics
8 ай бұрын
With this current code, you cannot. You may need some modifications in the code to reset the Kwh value using an external push button.
@muhammadshoaib3796
8 ай бұрын
Can You Guide Me Mam?
@subhrajitghosh3314
Жыл бұрын
Vro how can I get auth code
@nishanenwani8043
Жыл бұрын
How can we fix board error while compiling the code on Arduino IDE?
@beastscientist
Жыл бұрын
can you tell me what error you are getting
@nishanenwani8043
Жыл бұрын
code is no compiling for selected board ARDUINO UNO@@beastscientist
@dhananjayamurthyk8214
Жыл бұрын
How to use it for 3 ph energy
@beastscientist
Жыл бұрын
use one phase and do the changes according to your reaquirment an the code for more information contacat me
@peteranuforo8847
Жыл бұрын
How do you install ESP32 dev board module
@beastscientist
Жыл бұрын
ide
@omaramin3600
Жыл бұрын
why do my lcd doesnt output anything
@HowtoElectronics
Жыл бұрын
Adjust the contrast using the potentiometer at the back of the display. Or it could be the I2C address issues, the LCD display has 2 i2c address, please check and modify the i2c address in code.
@nikhiltm1711
Жыл бұрын
@@HowtoElectronics ma'am can you provide the i2c library link
@kabitachand2578
Жыл бұрын
👍
@falconzod
Жыл бұрын
Mam i need you help to setup esp32 file
@beastscientist
Жыл бұрын
what file little explanation
@jobertsor5112
Жыл бұрын
No detail explanation in programming
@malikumair5755
Жыл бұрын
Ap Ki mail id mil skte ha programming K hawale se bat krne ha
Пікірлер: 96