One of the most helpful video on YT. Thank you. I’m gonna be doing my camshaft myself for the first time on an X15 and this video helps a lot.
@webbykanyemesha6550
Ай бұрын
I enjoy this job
@kkoz_
Жыл бұрын
These are great videos. You should make more!
@miltonramirez2088
2 жыл бұрын
Very good explanation
@Rideniss
Жыл бұрын
Nice video bro especially the camera is very close thank you
@josevillegas9029
Жыл бұрын
Súper clean work area, nice video
@Giologico95
2 жыл бұрын
Nombre quiero ver un poco de todo lo que ustedes hacen🔧👍🏼
@thegarage6348
9 ай бұрын
Love it.
@23thebull
2 жыл бұрын
Awesome video
@LMdeGeneres
4 ай бұрын
I work for a fleet and I have an upcoming job. I gotta replace the front cover gasket. I need to pull the timing gears. I've never don't the job but I have all the info I need and I am comfortable doing it. Im just not familiar with setting the crank shaft pin and cam wedges to lock the timing in. A video would help but any advice would be much appreciated
@dwightdrinkard7561
Жыл бұрын
This video was very helpful I have rebuilt four of these motors in our fleet and I did it just like you have shown but I still get a lot of what sounds like gear train clatter the motors have been running fine for about a year just thought you may have a idea as to why it's so much noise.
@laloyup8164
Жыл бұрын
Have you timed the air compressor and high pressure fuel gear? Like it aint hurt anything if you dont. But they will make gear noise
@johnkidane7164
2 жыл бұрын
Great. Thank you!
@TheOldie56
8 ай бұрын
I have a comment/question. My 2016 isx 15 in apart now. The shop found the scissor gear and bushing apparently wore causing grooving of the front cover about 1/8". I'm quite sure this may have been a cause for rattling noise. My question is however is there any TSB covering this part as the motor has never been opened and has just under 700k at 596986 miles. Of course this gear and related components will now be replaced but I'm finding it difficult to get more info on this.
@germandarioorregoalzate4973
2 жыл бұрын
exelente video gracias saludos desde colombia❤
@jrjr4862
3 ай бұрын
Hi can you helpme i remove the tone ring for the cam and now i dont know how instal for get the rigth position
@jondavis8571
Жыл бұрын
thank you sir
@bassin_uce3732
2 жыл бұрын
Nice vid man I'm doing 1 right now at work and everybody at the shop has different ways of doing. But your way seems a lot simpler. I'm working with a isx w/o scissor gear will the adjustment process be the same?
@hectorfernandez8670
2 жыл бұрын
Question what is the torque on tha little idler gear that move the high pressure fuel pump ?
@JoseGonzalez-pp8ns
Жыл бұрын
Why are there manuals that say the calibration gauge is 10,000? And does not speak of 4000? Thanks
@davidsignor7931
6 ай бұрын
I have always used 0.010 gauges as per spec never heard of using a 0.040 gauge I think you could get into gear train noise with that little of clearance
@jameslast7555
2 ай бұрын
0.010" is for ISX15 CM570, CM870, CM871, twin cam engines 0.004" is for single cam ISX15 CM225o, CM2350, CM2350.
@111Moises1
2 жыл бұрын
thank very much...from toronto canada si lo puedes haser en espanol please
@jeffreyweston900
9 ай бұрын
In your estimation which is better the single cam or dual cam!
@elpro4684
7 ай бұрын
Excelente trabajo 👏 hacen videos en español
@cmon4792
2 жыл бұрын
Can you please post the tool part number for the injector cup pulled and installer!
@Mrjoel1737
2 жыл бұрын
Hagan un tutorial de un isx15 head repair
@philliphall5198
Жыл бұрын
Looks kinda hard but really its easy after the first few times
@brandon33371
3 ай бұрын
Do u have to readjust the lash if u have compresor out? My parts guy was being lazy and didnt order the gasket so I went ahead and did the cam gear lash with all the other gears besides the fuel pump until the gasket comes in, it just came to mind that it might shift teeth when i put it back in
@tankeryankercruz7795
2 жыл бұрын
Tku bro . How about on the cm871 “Cummins?
@sunartosunarto6831
11 ай бұрын
What was the fuller gauge used?
@tommysena594
2 жыл бұрын
isx Cummins front engine crankshaft seal
@philliphall5198
Жыл бұрын
Not hard if you buy the tools
@muthafukajones4536
2 жыл бұрын
Aren't the shims supposed to be ten thousandths?
@barienwhite1
Жыл бұрын
The Cummins spec I found says .010 or .25
@reggaeriderr
Жыл бұрын
👍 ur location
@shannonvanbrunt5689
Жыл бұрын
Your not supposed to disassemble the cam gear. It says it right on the gear in the video….
@CaseyMillerhome
Жыл бұрын
you're not supposed to disassemble the tone ring
@michaeldeslondejr5633
2 ай бұрын
If the ISC does not have a scissor gear and there is movement in between the fuel pump gear and camshaft gear, is that normal or need to be tight?
@essam8613
Жыл бұрын
It'[s not 109 ft/lbs. Its 75lbs then 120 degrees. you messed up big boi.
@manuelsaucedo8161
Жыл бұрын
Te equivocas, el Manual de Cummins dice 109 ft/lbs :)
@slopainguevara5615
7 ай бұрын
I agree I seen a lot of miss steps
@jameslast7555
2 ай бұрын
@@manuelsaucedo8161 It was 109 ftlb but the correct spec now is 75 ftlb + 120 deg. as per QSOL.
Пікірлер: 43