I enjoyed the chat while you changed the RMS. An an avid speeder, I used to be very anti-cop. Then there were riots within a mile of my house and now I always wave and say 'thank you' if they are within earshot.
@Goodtimesbadluckv2
2 жыл бұрын
How’s the leather taste
@bryanewyatt
4 жыл бұрын
Did you align the PPF when you did this, or did you do it at a later time?
@sammoreno8405
4 жыл бұрын
Hey man question I’m doing the transmission in my 93 Miata and I want to swap a 6 speed in there. I am wondering if they are all compatible. I already changed the drivetrain and differential to 1.8 lsd. I also got the 3.9 Torsen that’s supposed to be for a 6 speed. Have u done this before what do u recommend
@X7rocks
4 жыл бұрын
I just got the same clutch installed.havent driven yet though. How do you like it?
@chucky29949
6 жыл бұрын
Nice video, justified staying up late to watch as im replacing a leaky slave and old master tomorrow (today) morning on my 'new' 91 spec miata (has a '99 5 speed trans, ACT 4 puck sprung, redline MTL). Drove it for the first time yesterday and oh man never had so much fun in a car... beautiful steering feel/response and really fuckin loud with headers and only a resonator haha. Can't wait to take it to the track w/ the slicks. anyways, my comments.... Cant get over how clean your car is, the previous owner of mine painted both subframes like a John Deere green for some reason and its kinda dirty casually breaks out the 75mm socket lol interesting talk about your career there, hope retirement and shit works out and 22:49 hahaha
@TheSlipAngle
6 жыл бұрын
Thanks man 👍
@Calabyr
6 жыл бұрын
I know i always comment the same damn thing, but straight up you make badass videos man and straight DIGGIN the tunes you use as well.
@TheSlipAngle
6 жыл бұрын
Thank you Jake! 👍
@spencer2652
6 жыл бұрын
Any plans for the 5 speed you took out? It'll be incredibly interesting and helpful if you did a part 5 video where you take apart the 5 speed to show the input shaft bearing wear/play. I have a nb1 6 speed that makes a terrible noice 40% of the time when engaging first or reserve and always wondered what caused it.
@TheSlipAngle
6 жыл бұрын
I don't think it was the input shaft making the noise. I'll explain more in a later video.
@michelinov
6 жыл бұрын
of course you had a 75 socket laying around... how many miles would you say you have put on the parts you took out to make the swap ? clutch, fly , exhaust ?
@MrIbeetrollin
3 жыл бұрын
Are you using an NB1 six speed???? Looks just like mine but I cant find any info or rebuilders for a 99 6 speed from a 10AE. Got it for $350 with 32k miles! Please any info will help!
@TheSlipAngle
3 жыл бұрын
It's from an MSM
@kolesidisgiannis
3 жыл бұрын
Do you know the type of paint used on your transmissions? They look great
@lukamatijasevic890
6 жыл бұрын
Quinn great video but Croatia is playing f..... World cup Finals 🤩🇭🇷🇭🇷🇭🇷🇭🇷
@michelinov
6 жыл бұрын
you guys did very good , Bulgaria was with you.
@troyriderzsquad2158
5 жыл бұрын
I just bought a 2006 Miata 5 spd with bad engine (locked) came across this opportunity, owned by a co-worker that didn’t want to fix anymore. I’m doing a research on the 2.5 L swap and was wondering about the 5 spd and 6 spd transmissions...what are the differences between them and which one is better? Should I just swap a 2.5 L along with a 6 spd trans? What trans donor can I use!? Thank you so much for any info I can get.
@SpareTimeGearHeads
6 жыл бұрын
For your speedometer calibration use: Dakota Digital SGI-5E Universal Speedometer Signal Interfaces SGI-5E www.summitracing.com/parts/dak-sgi-5e I believe this modifies your speedometer signal. I will use this when I change my rear end ratio to 4.44 on my 94 Rx-7 with 18's
@andrewcowden9704
6 жыл бұрын
For the speedometer being off, Revlimiter can make you a scaled speedo face that matches your gearing. I was planning on going that route on my NA w/ a 6spd and 3.9 final drive, but with a 4.1 manual speed spender it was pretty much right on.
@dumbestoyster
6 жыл бұрын
I need to replace My OBX-R header. That Maruha is absolutely a wet dream.
@atotalpro
5 жыл бұрын
Quinn, What were you using to lube up the rear rear main seal before you put it in? (Im getting ready to do a rear main myself, and am trying to figure out the best procedure.)
@TheSlipAngle
5 жыл бұрын
Just some Valvoline Synthetic Grease ;)
@richardherring76
3 жыл бұрын
what miata did the 6 speed come from because it looks different to mine
@TheSlipAngle
3 жыл бұрын
A Mazdaspeed Miata
@danielstaar3916
5 жыл бұрын
Will a nc 6 speed manual trans fit in a 2003 nb? (Came with 5 speed)
@TheSlipAngle
5 жыл бұрын
Not without a bell housing adapter. Not to mention I would be willing to bet the PPF attachment is different as well. Why not just get a regular NB Miata 6 speed that bolts right in?
@jovanventura8726
5 жыл бұрын
How is the HF trans Jack working out?
@TheSlipAngle
5 жыл бұрын
It had an oil seal failure after the first time I used it. I am now on my 2nd unit and it seems to be okay.
@ArtVandelayOfficial
6 жыл бұрын
I thought the consensus was the 5spd has better ratios?
@snp4dx
6 жыл бұрын
6 speed holds more power
@TheSlipAngle
6 жыл бұрын
I wanted to shorten 1-5 a pinch and have a better cruise RPM. The 6 speed accomplishes that having the extra gear.
@rajvashi9210
4 жыл бұрын
So you can use a 1.6 flywheel on a 1.8?
@bryanewyatt
4 жыл бұрын
Yes, as long as you use a 1.6 clutch as well.
@k2ombs
4 жыл бұрын
Why did you opt for the 6 speed?
@TheSlipAngle
4 жыл бұрын
I explain why in PT 1
@mattwiser7982
6 жыл бұрын
Great idea with the 2x4, I wish I had done that when I replaced my clutch...
@neilobusk
6 жыл бұрын
Wake Santa up for the next one :).. Excellent stuff.. It wont hit 60 ind 2nd now ? theres ya speedo problem fixed :) have your cars ever seen rust.. its a brown awkward thing.. ?.. Do you watch any other car channels ?.. do some gun stuff vids.. Best wishes Neil
Пікірлер: 38