I always wondered why a standard gear system couldn’t be used with a motor, I guess it can. Awesome
@0-MACMAC-0
9 ай бұрын
shift a millisecond too fast and you'll find out why people dont use them alot
@deborahchesser7375
9 ай бұрын
@@0-MACMAC-0 probably wind the chain up in a ball or break the hub itself. You’d definitely have to be gentle with it.
@danieljonhson6367
3 жыл бұрын
I always have to ask why people don't do it that way more it works a lot better if you can use the gears.
@JamesPiccone
3 жыл бұрын
It actually doesn't, they suck ballz. Not enough torque to efficiently use gears and you still have all that driving through a bicycle chain.
@audieallen9734
Жыл бұрын
because it's a really difficult build, with a lot of things not quite fitting properly and guess work, trial and error. more things to go wrong...
@deborahchesser7375
Жыл бұрын
@@audieallen9734 I always wondered the same thing, why couldn’t a standard gear change system work with a motor. I guess it can if you take it easy shifting like backing off the throttling during gear changes. Your right though, lots of test fitting and modifications but once I get a welder I’m going to start messing around with building some stuff. Like putting a 670 Vtwin industrial motor in a YZ,KX,CR,RM 250 chassis. Or a trail buggy, again with gears. ✌️🇺🇸
@theLyzhendricks
7 ай бұрын
@deborahchesser7375 this whole bike was built with kits a motorized bicycle kit and a shift kit/jackshaft kit
@johnsheetz6639
2 ай бұрын
I bought one off marketplace that has that kit. I have seen some people that pulled it off but most people are against it because of the thin chain and the derailleur being weak.
@Littleevil9975
2 жыл бұрын
Looks great bro that green is killer looking good video
@vicentemacedo4896
2 жыл бұрын
Good night. It would be great if we had these two engine mounts that hold the shaft that transfers the force to the other side. Like, they contoured on some A4 sheets, each support on a sheet, for pdf so we can make our own supports. Think about the partner idea. It would help us a lot in the shaft adaptation process. Thanks for the attention.
@audieallen9734
Жыл бұрын
this is just super cool. I'd never do it because it would drive me crazy but good job!
@johngilbert396
Жыл бұрын
Thanx long time ago
@akilaferreiraoficial
3 жыл бұрын
Muito top 👏👏👏👏👏👏👏👏👏
@plzstandstill5120
2 жыл бұрын
I'm so doing this to my mountain bike I just started laughing when he was dropping gears 😂
@CarlosRivas-ni6ku
6 ай бұрын
Ese sistema me gustó compa 😮
@eddydaMotorizada-Rj
Жыл бұрын
Sua Bike ficou muito bonita com esse especto e o kit!
@johngilbert396
Жыл бұрын
english please
@NATAN52
4 ай бұрын
Translating (your bike looks very nice with this appearance and the kit
@johnargue2977
4 жыл бұрын
Looks good. I like the green. My bike goes about 25- 30mph. 60cc basic engine. Diamondback
@johngilbert396
4 жыл бұрын
TY MINE DOES ABOUT 50
@johnargue2977
4 жыл бұрын
@@johngilbert396 crazy fast. Bike looks awesome. 👍
@MrJasenstewart97
2 жыл бұрын
What size sprocket are you running?
@johnargue2977
2 жыл бұрын
@@MrJasenstewart97 I replaced rear sprocket. From 44T to 36T. More top speed .legs will be low speed 0-10mph. 32T available. Won't be street legal any faster. People doing 50 probably have jackshaft on it.
@ChickenwithaHelmet
Жыл бұрын
I'm wanting to build a motorized bicycle and the one I'm looking at has a planetary gearset in the hub. Really all I'd need to make it work is a jackshaft and then just use the crankset as a footrest lol.
@BrunoBlogs
2 жыл бұрын
Brabonaa
@santanaduran9702
4 жыл бұрын
Nice engineering
@Robert-hf5xr
4 жыл бұрын
Love that green cylinder head
@2strokeatvbro630
3 жыл бұрын
How’d he get that
@Gremlin_868
3 жыл бұрын
Ikr
@Gremlin_868
3 жыл бұрын
@@2strokeatvbro630 buy heat proof paint
@2strokeatvbro630
3 жыл бұрын
@@Gremlin_868 oh lol I already got some
@Gremlin_868
3 жыл бұрын
@@2strokeatvbro630 well there u go bro
@Giorgelima
3 жыл бұрын
Ficou show de bola assim irmão
@johngilbert396
3 жыл бұрын
ENGLISH PLEASE
@GeilsonAngelo
11 ай бұрын
@@johngilbert396bro he just said it was cool, calm down
@MGszamanVlog
3 жыл бұрын
Hi can I use part of your video to my compilation homemade inventions ?
@johngilbert396
3 жыл бұрын
cool please do
@MGszamanVlog
3 жыл бұрын
@@johngilbert396 Thank You
@31ijah.V
5 ай бұрын
You gotta change out that stock exhaust for a better system like a chamber and muffler set to increase power! You already got the cnc high compression head so that is by far way better than a stock
@zalafinari
Жыл бұрын
I know I'm 3 years late to this party but that thicker chain looks like it needed a tensioner. I'm making something similar to this setup but using an electric hub motor. Flopping chains are inviting disaster.
@buddahmayne9273
2 жыл бұрын
I like that
@bryancarvey4619
3 жыл бұрын
Love that neon green so sexy looking and sounds good to
@johngilbert396
3 жыл бұрын
thanx
@johnrutledge3892
Жыл бұрын
Thanks
@ivan872
4 жыл бұрын
How much space is needed between frame and the tyre? Nice vid
@johngilbert396
4 жыл бұрын
This is standard 26" and about 2" cleared from frame
@ivan872
4 жыл бұрын
@@johngilbert396 Thanks
@IrinBike
3 жыл бұрын
jadi pengen punya ini
@integrationofmanandmachine4714
3 жыл бұрын
thats sick hell of a ride
@dharmakissoon
8 ай бұрын
show how the pedal turns with the gas
@cwmaxfield2000
2 жыл бұрын
Love those fenders. I don't understand these Jack Shafts. Learning curve. My Trek has several speeds. Trying to figure it out. Lol.
@nathanmciver6496
2 жыл бұрын
You ever feel like "what learning curve?" Because thier is none
@diatonicdoug6525
5 ай бұрын
How bad does the derailleur bottom out when starting?
@meanderingmike7640
4 жыл бұрын
What rear gear cassette should i run to increase top end speed? Or what gear setup should i run with my jackshaft kit for more top speed?
@johngilbert396
3 жыл бұрын
i was using 8 speed and hit 55 mph on flat
@Lubyagin
Жыл бұрын
@@johngilbert396 Сильно! Как велосипед в этой конфигурации проявил себя? Как долго пользуетесь? Есть какие-либо существенные недостатки и узлы, требующие доработки?
@shadowguy_666-_-3
Жыл бұрын
What is the name of this part and what are you ordering it from?
@carloseduardodossantosribe8843
Жыл бұрын
Top, ys very good!
@johngilbert396
Жыл бұрын
ty
@regie165
4 жыл бұрын
Can you record a video while its running?
@jhonvictor5778
Жыл бұрын
Linda
@jpjp9695
4 жыл бұрын
What size chain goes to the back of the gears from the jackshaft kit?
@jimjensen1096
3 жыл бұрын
Usually a size 415 chain comes with that motor.
@victormanuelfuentes3041
4 жыл бұрын
Que velocidad alcanza de esa manera
@mstzmikebsteviec1119
3 жыл бұрын
Nice set up awsome
@johngilbert396
3 жыл бұрын
ty happy new year
@g-rocksales870
2 жыл бұрын
Now let's see you on it
@joeypike526
Жыл бұрын
How fast does it go
@Mrbotlegmechani
7 ай бұрын
Wait how tf does the bike chain handle that
@gewizz2
2 жыл бұрын
but what is that front chainring? how it has freewheel? huh?
@bassbikesbowsandbullets423
4 жыл бұрын
Any problems yet?
@Westhelockpicker
Жыл бұрын
A good expansion chamber would do wonders for you
@ericmartin6657
2 жыл бұрын
Do the pedals move when you give a gas and the clutche is engaged?
@johngilbert396
2 жыл бұрын
no it has its own free wheel on the pedals
@nicolasdrez
26 күн бұрын
WHY DO THE PEDALS NOT ROTATE WHEN YOU ACCELERATE?
@Gamer-xk5rs
Жыл бұрын
Was the point of this is to get the most speed, if so cant you just use a smaller sprocket instead of the one it comes with that goes on the other side and wouldn't have to add extra weight? Or does it make a difference with both gear shifts that I don't know about.
@dekoldrick
3 ай бұрын
Something like this would optimize engine's torque range for each gear so you can control if you want more power for acceleration and going up hills easier or more power for more top speed on flat ground. With only one gear, you'll have to settle for in between which won't be the best at both.
@ryze6726
3 жыл бұрын
Top speed?
@ChuckHaney
3 жыл бұрын
Is that shift kit from sickbikeparts? My seat tube is 1.250" ...they sent me 1.125" clamps. They told me that's correct. There is no way to get those clamps on without damaging the paint and/or the seat tube. Square peg, round hole.
@johngilbert396
3 жыл бұрын
got mine from bbs
@ChuckHaney
3 жыл бұрын
@@johngilbert396 Those u-bolt style clamps, did they fit perfectly to the seat tube or are they technically too small? My seat tube is 1.250" diameter but they sickbikeparts tells me that I'm supposed to use a 1.125" clamp on it. I don't see how that's correct.
@johngilbert396
3 жыл бұрын
@@ChuckHaney mine fitted str8 on
@glendopilongo7516
3 жыл бұрын
Sir where can i buy that conversion kit, so i can use the shifter on the rear spracket? Thank you in advance fpr you reply
@johngilbert396
3 жыл бұрын
got the main kit from ebay .but you mite want to upgrade the chain as it will brake on you .www.bikeberry.com/bbr-tuning do a good kit and more relieble good luck in your build
@bryancarvey4619
3 жыл бұрын
What is the conversion kit called? Like what is the name to look for it?
@ColinandDaniel
3 жыл бұрын
Sick bike parts shift kits are superior
@motorizedbicyclenation53cu90
2 жыл бұрын
Get the sick bike parts hd kit heavy duty and their chain will work personally I don’t need gears some of mine hit 40 with a 44t sprocket with only mild port work just cleaning them up good and setting carb correctly running right ratio 32:1 not40:1 and going 45 is so easy just an arbeo carb and again mild work mild mods can go 50 with a 38t but a 44t is 45 plus climbs hills takes off dead start
@user-vp9ym9fu1b
2 жыл бұрын
how did you make sure that the pedals of the wheel do not turn
@johngilbert396
2 жыл бұрын
It has a special one way hub bearing
@facundoamadeocabrera2496
4 жыл бұрын
The name of thats lights?
@Felix_Edmundovich
2 жыл бұрын
Does it move well from a place without pedals?
@johngilbert396
2 жыл бұрын
yes
@brandonwaughtal6391
8 ай бұрын
4 years later how is that Jack shaft gear shifting working?
@johngilbert396
8 ай бұрын
i sold it 3 years ago
@matthewnorman9803
2 жыл бұрын
What type of chain do you have on the derailleur
@johngilbert396
2 жыл бұрын
just a standard one
@crotilio
3 жыл бұрын
Boa tarde, onde comprar?
@penceliyevceyhun
6 ай бұрын
Mende 80cc dir ancaq bele deyil bu Cox eladir
@shanewestphal7986
3 жыл бұрын
I bet it needs constant greasing and adjusting that index probably hates you 🤣
www.ebay.com.au/itm/253564599021?ul_noapp=true peguei esse link em outro video mais chegou certinho 20 dias.
@inventandoideias
4 жыл бұрын
@@graudubode9784 e compensa ter o kit? ou da trabalho?
@cicerodantas2635
4 жыл бұрын
Boa tarde amigo vc conseguiu comprar o kit eu tambem queria um como faço para comprar
@user-jk7hy3mr8x
7 ай бұрын
I wonder can you do that with a 212 predator engine🤔 I would make into a 4 speed
@johngilbert396
7 ай бұрын
i would like to see that
@putintv8944
Жыл бұрын
How do you that
@user-sq5sy7bk5m
2 жыл бұрын
hi ^)
@barbarabarker8256
3 жыл бұрын
Hey man with the gears how fast have you been able to get her to go
@johngilbert396
3 жыл бұрын
about 55 mph
@jackkeyhoe7072
2 жыл бұрын
WHERE DID YOU GET THOSE LIGHTS ?
@johngilbert396
2 жыл бұрын
Ebay
@Westhelockpicker
Жыл бұрын
Have you had any problems? I want one but there's a lot of negative videos about them
@johngilbert396
Жыл бұрын
Yes find a good chain any cheap Chinese It will break
@Westhelockpicker
Жыл бұрын
@@johngilbert396 any suggestions
@richardrossell909
2 жыл бұрын
where do i get this jack shaft kit and how hard is it on chains
@johngilbert396
2 жыл бұрын
I got mine from eBay
@johngilbert396
2 жыл бұрын
If u change gears with high revs you will break the chain
@shaguftashaikh3038
3 жыл бұрын
Kitne ki hai banaa ke dekho kya
@Motorized-BikerUk
3 жыл бұрын
Hey bro.. I've got the sick bike parts kit on.my carrera 7 speed. I've tried loads things but my chains keep coming off and summat slips in 3rd gear onwards I've tried loads of things. Even got the sick bike.parts tensioner I brought separate and everything still just goes belly up. To the point its un rideable.. I have a few questions and stuff do you have an email I can contact you on m8. Tarr Sy
@johngilbert396
3 жыл бұрын
hi there reach me on locksmith24hr@msn.com
@adamb8851
3 жыл бұрын
Sorry but all the links to the kit weren’t working mind sending another one?
@johngilbert396
3 жыл бұрын
ebay
@yaringolan9260
Жыл бұрын
From whare you bought the engine head
@johngilbert396
Жыл бұрын
ebay
@yaringolan9260
Жыл бұрын
@@johngilbert396 k. This engine need an engine oil or somethink?
@brennoncantrell5867
3 жыл бұрын
That’s scary lol
@honoriopedrodasilva9698
2 жыл бұрын
Boa tarde , como adaptar o motor do lado direito ?
@facavocemesmo1323
2 жыл бұрын
Este sistema se chama jack-shaft 80cc, procure no youtube, tem no Aliexpress a venda, tem fotos das peças, se tiver habilidades é so copiar e fazer o seu, eu digo que vale a pena, pois podemos usar marchas, eu estou fazendo o meu, catraca 6v atrás e 2 coroas no pedivela, retirando o cambio dianteiro. Aqui tem uma visão melhor das pçs kzitem.info/news/bejne/w3iix4J3fKiarJw
@janielalejandro2470
11 күн бұрын
La has probado cuánto km coge en el última velocidad?
@johngilbert396
11 күн бұрын
55mph
@jormanhernandez6850
Жыл бұрын
Where can I against the PDF of that to do it?
@johngilbert396
Жыл бұрын
i dont know sorry
@denwerfox2028
2 жыл бұрын
what is the maximum speed.
@johngilbert396
2 жыл бұрын
58mph
@narcissistinjurygiver2932
2 жыл бұрын
where can i buy this kit?
@johngilbert396
2 жыл бұрын
ebay
@Felix_Edmundovich
2 жыл бұрын
Max km/h?
@johngilbert396
2 жыл бұрын
55mph
@ferrelli76
3 жыл бұрын
Is that an Amazon jackshaft kit.
@johngilbert396
3 жыл бұрын
No come from china
@blackangel75171
3 жыл бұрын
if you go to sick bike parts you can buy a better quality jackshaft
@GhostOfDamned
3 жыл бұрын
The spokes dont like that
@sylwesterkwiatkowski4653
2 жыл бұрын
kzitem.info/news/bejne/1WeErI2Xp5aekmk Zbuduj stały prąd elektryczny 14v Z wyłącznikiem start stop Dla pojazdów elektrycznych
@humorrisas22
2 жыл бұрын
Sonido es pecimo.
@osirisarriaga3769
2 жыл бұрын
Q precio tiene una bisimoto
@johngilbert396
2 жыл бұрын
english please
@sueltonjosedasilvaaguiar8290
Жыл бұрын
Eu.quero saber ser.tem.pesa.para.bicicleta motorizada pé de vela.com.ar.coroa roda.livem
Пікірлер: 157