I recommend using a oil pan that doesn't have a hole in it 👍
@ceezfoe2092
Жыл бұрын
😂😂😂😂
@Sniffy-Biden
Жыл бұрын
Did mine works just fine for 6 months 😂 2" hole and cracks worse than this. Using aluminum patch works best with jb and epoxy over it, hard paint afterwards
@wayne6961
10 ай бұрын
no shit
@kennethhoppe2259
8 ай бұрын
Smart Ass
@bobbybowers4065
8 ай бұрын
Yep
@rupe53
Жыл бұрын
I have used JB Weld on those corroded areas of an aluminum intake manifold, where the coolant just eats them up from years of seeping. Let it harden overnight, then hit with a flat file before installing a new gasket. JB (original) is good to over 500 degrees. A new manifold for a 4.3 Chevy was about $600 and several days out.... so this has worked well.... and still holding years later.
@lazywarrior
Жыл бұрын
I think this 1$ fix will be fine since the oil pan is not pressurized.
@Sneekwelding
8 ай бұрын
I’m a welder and I still use jb weld from time to time. its perfect to use on thin corroded metal
@richardahola692
Жыл бұрын
Many many years ago I was on a long trip with a friend. We stopped for gas and he forgot the kickstand. Bike fell over when he got off and the shifter punched a hole in the stator cover and all the oil ran out. It was Sunday and no bike shops were open. I bought a back of 10min epoxy and some masking tape. Took the cover off and glued it. We waited a half hour before filling the oil and leaving. It held and he had a window to see the oil level.
@davidskillen9035
Жыл бұрын
And as a plus, the oil changes itself. No more paying for oil changes for this guy
@marckemp9955
Жыл бұрын
I bought a Chevy truck several years ago. I was checking all the fluids and I found what appeared to be a pumpkin gasket leaking. So I stopped at a local parts store on the way home and they said they didn't stock the gasket and just use RTV. I went home, cleaned it up, RTV'd the heck out of it and filled it back full of fluid. Next day I noticed gear oil on the drive wheel and what appeared to be a leaking pumpkin cover. But I got to looking closer and it was a small hole in the cover near the top. I had missed it the day before because it had been leaking no telling how long and it was pretty dirty. So I cleaned it best I could with the cover still on and used some black RTV and that cured and fixed it until I could get some JB weld the next day. I cold welded it that next day and it wasn't a problem ever again..or not in 11 years. Today I started working on manipulating the metal on a bent engine pan. It's $75 for another 6 qt pan. Old school pans weren't this aluminum crap they use on today's stuff and when they were bent you could put them on the floor with blocks of wood inside and pound them back into shape.
@tuftedoge7262
17 күн бұрын
Definitely would just buy a new pan, but do as you please
@peted5217
Жыл бұрын
it's JB . It'll work good using their instructions
@bobocaterpillar3697
Жыл бұрын
i dont know whats worse. the jb weld crap OR putting the jack stand on the paper thin floor pan.
@BigDipper79
Ай бұрын
Don’t ever do this unless it’s an emergency repair to get the vehicle moved.
@Lancelot0311
Ай бұрын
Does it hold well with the high temperatures ?
@Forever4clothing
2 ай бұрын
Can I remove my lower oil pan withiut messing with the transmission ? I need to replace mine but I want to replace it myself if it’s easy on my Audi a4 2017
@spelunkerd
Жыл бұрын
Welcome to the genre of trolling videos, where clips are made just to enrage anybody who knows better. Makes money by tickling the algorithm, generating views, and funny for those who think they're smart. Problem is, there are many who are too ignorant to recognize satire. Don't kick those people when they're down, especially for money.
@rotboyzgarage
Жыл бұрын
It's the cheap way to fix the oil pan, had no idea of the engine was good so no need to replace the pan, holds oil and doesn't leak a drop so it's a good temporary fix
@mdacosta7013
Жыл бұрын
I couldn't have said that any better myself this is the latest trend I been seen all over the Internet when will the algahythms catch on to what's going
@mdacosta7013
Жыл бұрын
Thanks to shorts everyone is a Master mechanic and will show you how to do things the wrong way
@dustinselby1368
Жыл бұрын
Just grab a oil pan in the junkyard. It's not like you're broke down in the middle of nowhere.
@sixfoursoul2538
Жыл бұрын
you say that but not all oil pans are easy to remove , I have a dakota entire engine needs to lifted to get pan off , 800 dollar job, this fix will help you until you can afford do the job
@gzbravo2097
10 ай бұрын
Could this be used to seal a small leak on a power steering leak?
@johngaltline9933
Жыл бұрын
Probably could have used with saying it was intended as a temp fix just to see if the engine was any good. the video makes it sound like it was actually fixed and intended to be daily driven like that.
@tiko4621
3 ай бұрын
I daily drove a JB welded pan for years. Granted, I dropped the pan and JB welded the inside and outside cracks. Was a quick on hand fix to get me through the month to the next check, ended up lasting 4 and a half years before I actually destroyed the pan going over a nasty speedbump, the pan broke at a totally different point and the weld looked perfect inside and out.
@nate3231
9 ай бұрын
Not recommended but if you’re in a pinch and need to do something like this go get some sheet metal aluminum and some regular full strength jb weld and cut out a small circle with some shears and put a ring on the circle jb weld that to the oil pan then put another bead going around the circle on the outside and that will be much better than doing it this way
@arthurmccutchan7000
Жыл бұрын
If its hit hard enough to have a hole it very likely cracked replace the pan and check the oil pickup too
@tobberfutooagain2628
Жыл бұрын
They do this all the time at the BMW dealer….. after you zign ze paperz….!
@Thebackwindow
4 ай бұрын
Is this the oil pan who in a previous short just jabbed a screw driver through it
@MikeHudson-px2gc
Жыл бұрын
Just doubled the value of the car
@fukusmurk6580
7 ай бұрын
Don’t yall think it would work better if he got a peice of steal to go across the hole with JB weld on each side leaving a rectangle steel piece |==| ⭕️ pulling it down so it can stick to the metal leaving two smaller holes on each side then doing it his way? Idk I feel like it would cap it in a way from each side rather then just jamming on one side
@amanuelwordessa4057
Жыл бұрын
Yea now jb weld that connecting rod that made the hole in the first place and now your good
@rotboyzgarage
Жыл бұрын
Surprisingly the engine didn't have a blown connecting rod, first thing I checked through the hole with my bore scope, all rods looked good, jb weld and some oil and she ran decent
@amanuelwordessa4057
Жыл бұрын
@@rotboyzgarage having a hard time believing something put a hole from the outside with no dents ir markings around
@rotboyzgarage
Жыл бұрын
@Amanuel Wordessa kzitem.info/news/bejne/raKvnIWorolnfaQ We got it running in this video, in the previous you can see the pan that's been jb welded, it ran ok for sitting like 15 years with a hole in the pan 🤣
@TeamMajin
Жыл бұрын
Should of used steel mesh with it
@MrWallace484
Жыл бұрын
I’d spray something overtop at least just to seal a little better
@Houndzee
Жыл бұрын
Good enough
@robertehatten4847
Жыл бұрын
Just get a new oil pan…..
@charleslease9280
Жыл бұрын
Replace the pan or weld it up that’s a hack way
@raymondeldridge6068
Жыл бұрын
Why is the Jack stand on the floor board ????😂
@josephmac2386
Жыл бұрын
Either this is a joke or you are out of your mind. Replace oil pan
@rotboyzgarage
Жыл бұрын
Not a joke, car hadn't run in roughly 15 years so no reason to buy an oil pan if engine was trashed. Didn't leak a drop of oil and was able to get the engine running to see if it had a knock or any issues which could occur due to the hole in the pan
@josephmac2386
Жыл бұрын
@@rotboyzgarage Oh I thought this was a daily driver. My mistake
@Steve-oj7mt
Жыл бұрын
Exactly
@rumplejesusskin
Жыл бұрын
How long did it last until oil seeped out?
@rotboyzgarage
Жыл бұрын
Still holding with no leaks
@Jacob.C.9397
2 ай бұрын
I think jb steel stick is better
@dacrd
Жыл бұрын
MiNt
@mikex519
11 ай бұрын
Bro. Scab a piece of metal over the hole and bolt it to the pan. Use the JB weld for the seams...
@BW-kv9wj
Жыл бұрын
Just buy a new pan
@wymple09
Жыл бұрын
For a car that's already junk. Sure.
@sixfoursoul2538
Жыл бұрын
you say that, but not all pans come off easy with out lifing engine.
@isaiahmerida5475
6 ай бұрын
I’m gonna have to do this until my next paycheck i hit a lump of ice that fell off of a vehicle that was in front of me
@miss80329203
2 ай бұрын
I have a crack in my oil pan. A oil pan for my '06 Kia spectra is $220.00 from O'Reilly's 😮
@JamesJones-gy1fl
Жыл бұрын
Just replace it
@mikemartinez5436
Жыл бұрын
I would have thought a new pan might be in order, but you do you. (I’d never employ anyone who thinks this is a good idea)
@rotboyzgarage
Жыл бұрын
Car sat for over 15 years and had no idea if the engine was good, do it was a temporary patch to hold oil before dumping money into something that may have had a knock or been bad
@wayne6961
10 ай бұрын
good thing you aren’t anyone’s employer tf lol
@user-co8iz2ng4u
5 ай бұрын
Bad idea you need a new oil pan
@rotboyzgarage
5 ай бұрын
A new oil pan is the proper fix. This is a temporary fix to help someone get out of a bind. Ive broken oil pans in the woods before on rocks and this will let you get out of the woods and keep driving until you can get a new pan. Also this car was sitting for 20 years with a hole in the oil pan so no reason to buy an oil pan for something if you dont know if the motor is healthy or not
@emerybryant
Жыл бұрын
not recommended! but it should hold up fairly well. 😅 so bit of a double edged sword
@morganfrmn
Жыл бұрын
It would be best to spend the $20 and get another oil pan. If you must use jb weld the gray is better. You should remove the pan and mushroom the inside like you did the outside. Then it would last
@rotboyzgarage
Жыл бұрын
The jb water weld is specifically resistant to oil,gas and diesel where as the grey steelstik is not, ive used both and the waterweld works better and doesn't leak. Also a non oem mercedes oil pan is $120 and the main reason for this was the car sat over 15 years so was unsure of the engines condition or if it would run. It's a temporary fix or something that would work in a situation like this as the engine was in unknown condition
@morganfrmn
Жыл бұрын
@@rotboyzgarage I drove an old Mercedes for years. Junkyard oil pan is easily obtained. My motorcycle was shot about 10 years ago and I used jb weld to fix. Would you like a picture. The key is smashing the inside like you did the outside. And I used the gray and it's still there. Say the word I'll shot you a photo.
@heffedirte6243
Жыл бұрын
It's not 1972. Where can you get a $20 oil pan? I want to buy them all and resell them
@lesliechung79
Жыл бұрын
U pull it junkyard for $20 u pull it & save $$$
@emergencylowmaneuvering7350
7 ай бұрын
@@lesliechung79 AND A MONTH LATER, RUST ALL OVER.
@artemioignacio7526
Жыл бұрын
Put some bubble gum on top of jb welding. 😂😂😂
@BillySBC
Жыл бұрын
Should put a small piece of sheet metal over the hole and then JB Weld over that, this way the JB can't fail and wind up with pieces of it in your oil pan.
@1961timmy
Жыл бұрын
What the hell did I just witness
@cheesyshow8413
6 ай бұрын
Pause
@arnoldojeda7883
Жыл бұрын
How long you let it cure?
@Aceedmonkey
10 ай бұрын
Is the repair still holding?
@rotboyzgarage
10 ай бұрын
Yes
@Aceedmonkey
10 ай бұрын
Good to hear! After watching this I’ve used the same in mine!
@huguebegin4274
Жыл бұрын
come on man.....
@heffedirte6243
Жыл бұрын
Use gloves then don't use gloves? I'm confused......I would definitely use something more abrasive for physical adhesion not, just relying on chemical adhesion
@rotboyzgarage
Жыл бұрын
Only had so much time for the short for explanation, but when applying it the gloves tend to stick and pull at it vs help smear it into the material your working with so I will normally just use a finger to try and tap/work it in, but using gloves to mix it will eliminate like 85% of the mess you would have on your hands if you didn't wear anything
@brianjohnson4211
Жыл бұрын
I would NEVER trust that 😅😅😅😅😅😅
@rupe53
Жыл бұрын
he only had to trust it long enough to see if there was any other damage. (this is why you read other comments first)
@bogdanantal2120
Жыл бұрын
Really ? Wtf?
@LOLAP95
8 ай бұрын
Thats called a scratch or scouring pad. Thats not a brake pad sir
@sledfast3527
7 ай бұрын
He said scotch brite pad… not brake pad😂
@gillgetter3004
Жыл бұрын
I don’t know can u really trust that?
@mikeredline27
Жыл бұрын
That is the worst thing in the world you could do
@rustyscriver9426
Жыл бұрын
Ya should last bout 1 day. Nice fix
@rotboyzgarage
Жыл бұрын
You would be surprised how long this stuff lasts when applied properly, had a pan like this for about 3 weeks on a vw tdi daily driven and it didn't leak any oil, it's a good temporary fix until you get a pan or for a woods beater
@TheTylu
Жыл бұрын
PRO NERD WORK 😂
@cody39yrs
Жыл бұрын
You should explain why you did this so people could understand why, that's what the description section is for. Or explain yourself in the comment section.
@monotheis6889
Жыл бұрын
No way
@rotboyzgarage
Жыл бұрын
It's still on the car with oil in it, doesn't leak a drop 🤣
@landonlehman5497
Жыл бұрын
At least use some screen mesh..
@DS-xj8bp
Жыл бұрын
Umm. No
@ChadieB
Жыл бұрын
That happened to the gloves you recommended using?
@rotboyzgarage
Жыл бұрын
Couldn't fit the whole video in with the shorts time frame, but for mixing it I recommend using gloves so you don't entirely coat your hands in it, but when applying it tends to stick to the gloves to much and makes it hard to have it adhere right. So using your bar fingers I find you can tap/press and smear the edges into the metal and I have had good luck with this method
@stancoleshill8925
Жыл бұрын
NEVER HOLD ! SORRY, WHY WOULD YOU POST THIS B S ???????????
@franciscosuarez2346
11 ай бұрын
Just get a new oil pan they are like 20$ lol
@jaymartinson3236
11 ай бұрын
If you can't change it yourself, shops will often quote you $500-$1000
@bryanrodriguez1309
10 ай бұрын
My oil pan is $400 +
@ro420green4
10 ай бұрын
This mf please don't.
@cconrancconran3991
Жыл бұрын
Looks brand new lol😮
@tobberfutooagain2628
Жыл бұрын
Gosh, I hope you paint it when yer done…
@Paumonsu
Жыл бұрын
You didn't even remove it to clean the insides
@mikegraham395
Жыл бұрын
That is a terrible fix I would never let you fix anything ever
Пікірлер: 111