Great video, I just ordered a clutch cable and new gas pedal from you guys
@Weightlossjourney24
4 жыл бұрын
Thank you for these videos I’m working on a SandRail
@arifdarmawansetiyadi5842
3 ай бұрын
Thankyou for the Vedio Bro
@Sam_Mebane
3 ай бұрын
Our pleasure!
@haroldsteptoe6402
6 жыл бұрын
such useful information ! your video really helped me through the process of changing my clutch cable .. cheers guys
@SteveBlack-kj3pm
10 ай бұрын
Exelente video. solo falto engrasar los cables ??
@Sam_Mebane
10 ай бұрын
Si ves que el cable viejo salió con mucha grasa, entonces no necesitarás agregar grasa. De lo contrario, todo lo que se necesita es una capa ligera.
@Its_about_that_time
2 ай бұрын
Does rhe accelerator cable tube need to be attached to anything or does it just hang there
@Sam_Mebane
2 ай бұрын
It just "hangs" there, when it is run through the fan shroud tube, it sits between it and the chassis.
@arielshtern4125
3 жыл бұрын
Is removing the engine really necessary?
@Sam_Mebane
3 жыл бұрын
No, not at all.
@gravityTattdrumr11
2 жыл бұрын
What type of grease is used for the brake pedal push rod and such? Great video! Very helpful on my 61
@Sam_Mebane
2 жыл бұрын
Any grease would work, we happen to have some CV joint grease handy so it's our go to lately.
@fayjason
5 жыл бұрын
Ive got a dunebuggy that’s shortened 3 inches. Could you make a video on how to install a cable shortening kit . Thank you
@JBugsVWParts
5 жыл бұрын
When we get the right project car, absolutely. In the meantime, the cable shortening kits are pretty simple to install. With the exception of the clutch cable kit, the cable ends are cut off and a new end is slid over the cable and held in place with a set screw. For the clutch cable, the end is cut off, the cable is routed through the new end and a nut is threaded down to hold the cable in place.
@fayjason
5 жыл бұрын
Hey that you Jbug
@gsxr419
2 жыл бұрын
I'm experiencing a hard shudder in reverse on any grade. Could that be a bowden tube adjustment?
@Sam_Mebane
2 жыл бұрын
It could be, but if it is only in reverse, I would first check the cable adjustment and go from there.
@gsxr419
2 жыл бұрын
@@Sam_Mebane Front trans mount is toast everything is coming and and getting refreshed. Thanks for your reply.
@Manny2jz
4 жыл бұрын
My clutch pedal falls to the ground and doesn’t return after I replaced my cable
@Sam_Mebane
4 жыл бұрын
If the cable is attached to the arm on the transmission, then chances are the cross shaft arms inside the bellhousing have broken off. That, and the spring on the cross shaft is broken.
@1catbrains
Жыл бұрын
Pedal stop plate
@Devin_Stromgren
6 жыл бұрын
What exactly is the point of that roller accelerator pedal?
@JBugsVWParts
6 жыл бұрын
In 1957 and older Beetles, the roller pedal was stock. Some people like the vintage look and simplicity of the design. Others like the smooth, albeit odd operation compared to the metal pedal. Either way, it just comes down to personal preference.
@Devin_Stromgren
6 жыл бұрын
Thanks, although since I asked I had found most of that out on my own. Since you are answering questions, what is the part number on your website for that heavy duty accelerator cable?
@JBugsVWParts
6 жыл бұрын
All the parts we used in the video can be found in the video description, although it looks like we missed that one. The heavy duty accelerator cable we used for this installation can be found here: www.jbugs.com/product/4860-7.html
@TylerHarney
5 жыл бұрын
Is there something holding the clutch cable tube to the chassis clutch tube? I can't seem to disconnect mine.
@JBugsVWParts
5 жыл бұрын
There is no mechanical part holding the tube in place other than the bracket at the transmission. Once the bracket is removed, gravity, tension, grease, dirt, road grime, rust, etc. are the only things holding the tube in place. A good tug is usually required to break the tube free of the chassis.
@johncollins5552
Жыл бұрын
@@JBugsVWParts Never seen rear disc brakes on a bug before, fancy pants, factory never did those afaik!
Пікірлер: 29