Color-coded wiring instructions for 2013 JKUR located at 21:20 👍🏻
@SergioLopez-tq6wq
3 жыл бұрын
I just ordered some KBD fenders which looks identical for the poison sypder's one but in polyurethane and I was looking for a video to do this exact same thing, now I know that I can also plug the turn signals to the markers, great video
@JKsouthwest
5 жыл бұрын
Good job on the video, with some helpful wiring tips. Great choice going with Poison Spyder fenders.
@coldsteeloffroad
5 жыл бұрын
Thanks for the comments, much appreciated!
@4207Points
2 жыл бұрын
Will these replace factory turn signal or will it always blink fast I lost my factory connection end and was looking for a work around instead of going back to factory because I like this idea.?
@coldsteeloffroad
2 жыл бұрын
I'm fairly certain that the lights would blink fast as if there was a factory bulb burned out. There should be a way around it though by simply wiring in a dummy-load resistor in series w/the headlight to fool the PCM into thinking there's a factory bulb present. Many aftermarket LED taillights for Wranglers require this to be done to prevent the rapid turn signal flash. I don't remember off the top of my head but I think it's something in the ballpark of a 50 Ohm resistor...you'll have to do a little research. Also be aware & plan your mounting location wisely as the resistors can get very hot when in use. Thanks for the view!
@toyotaluv
3 жыл бұрын
Great video, thank you! Did you need the LED relay in the steering column?
@coldsteeloffroad
3 жыл бұрын
I simply wired these in place of the factory fender lights. Did not need to add any relays & no fast-flash problems or any other problems still to this date. Thanks for the view & comment!
@roblippe4245
2 жыл бұрын
Super helpful - thanks for posting
@83wildmustang
Жыл бұрын
Which white wire is it? White with gray or green stripe you just say pink to white wire?
@coldsteeloffroad
Жыл бұрын
21:20 here you go.
@83wildmustang
Жыл бұрын
You said white with red tracer I don’t have a white with red pink tracer. Mine is white with gray line and white with green line. 2014 JK
@coldsteeloffroad
Жыл бұрын
@83wildmustang are you wiring in a 2 wire or 3 wire LED light? Are you trying to use it as both a turn signal & solid marker light, or just a solid marker light that comes on when you turn on the parking lights?
@83wildmustang
Жыл бұрын
I apologize I didn’t specify. Im wiring in a 3 wire round led. I’m using as both marker/turn. I wired it just like yours and all I get is turn signal. I have a black, white with green stripe and white with grey stripe on my park turn grill lights.
@coldsteeloffroad
Жыл бұрын
@@83wildmustang did you use the existing 2-wire harness for the FENDER light on the Jeep side to wire/power the LOW brightness & ground of the LED, and only tapped into the grill marker/turn light wiring to power the HIGH brightness of the LED? If so & still not working, please specify the colors & functions (high/low/ground) of the 3 wires on the LED you are installing, and I will pull up the schematics for your Jeep and tell you how to wire it. Wiring can be tricky...but We'll get through it!
@richk4452
4 жыл бұрын
Good video, if you do much wiring get a heat gun for that shrink wrap, way better than a flame
@coldsteeloffroad
4 жыл бұрын
I agree w/you, but for just a couple of heat-shrinks on environmental splices I opted for the ol' Bravo1Charlie for efficiency's sake. Thanks for the view & comment!
Пікірлер: 24