Just finished doing this to my renegade. Your instructions are on point. To those figuring it out, I and many others couldn't get the quick connect coupling off (without risk breaking the radiator). So save yourself time and buy a universal steel clamp with the Caterpillar or ez screw. Break the steel clip next to the quick connect and simply pull the hose from the connector. Be sure you have a catch pan. Also I would highly recommend a kit designed for radiators. Comes with all the attachments and a big funnel. Lastly my flush took about 3-5 hours. The most time consuming part is filling it back up with coolant and burping/purging air. You need to rev the engine until about 3000RPM and hold it there. Watch the coolant level rise. If you hold it to long it'll bubble up and go everywhere. Find the right tempo. rev up then stop and let it idle. Coolant level should go down. It was a messy job but it can be done at home. Be sure that at bare minimum you add all required coolant. Dont forget to compensate for the coolant that will spill everywhere. It's 1.7 gals of coolant/1 gallon and 89.6 oz. I used a scale. EDIT: upon reviewing the service manual there's a simple step that I think will make things more efficient. Once you get to the point of closing the valves and adding coolant to the max level of the tank PUT THE CAP TO THE COOLANT BACK ON AND TIGHTEN IT. Then proceed to start the engine and run at idle for 2 minutes. (Revving may need to be done here. Refer to above)Stop the engine and after it has cooled checked that the fluid level is not at the max mark on the tank. If it is keep repeating until it isnt. I think initially I was missing this step which is why it took so long for the air to be bled correctly. I hope this helps everyone.
@MilwaukeeMade1995
2 ай бұрын
This is by far the best video ive ever seen on youtube to do a simple coolant flush
@trackerrrr
Жыл бұрын
You don't need to completely remove the bleeder screws. Two or three turns is fine, the air will escape around the threads and you can close them faster.
@marksindustries567
Жыл бұрын
I can't believe how difficult they made it to get to a service point that's so frequently used for maintenance. I have a 2019 jeep compass and it took me two days to find out how. Thank you
@leontrey777
8 ай бұрын
I know Right! I never could get that quick connect piece off either after hours of trying. Ended up snapping the permanent hose clamp and just replaced it with a reusable one, and afterwards it only takes moments.
@DarylWilliams-m4b
Жыл бұрын
I'm about to change a water pump on 2.4 renegade, and I really appreciate this informative video 👍
@TheCamra17
Жыл бұрын
Personally, I found it was a 100% easier to just remove the front bumper. Takes only a few extra minutes and I recommend getting extra trim clips since you'll probably break the first set. The coolant reservoir is right behind the bumper and super easy to reach once it's removed. I also say this helps because the coolant will splatter EVERYWHERE. So it's nice having extra room to hold a funnel under it. Seriously, this will get very messy so i recommend doing it over a garage floor with a mop nearby. For some reason, Mopar coolant is also super sticky so Pinesol and Simple Green helps.
@leontrey777
8 ай бұрын
I successfully flushed my Renegade coolant thanks to this video. Appreciated ✌ Subbed ❤
@peterlucas2998
Жыл бұрын
I liked this. Simple and straight to the point. One note; little something about burping the system after the fill and bleed would have been helpful. 🙂
@goriarell
Жыл бұрын
System on this vehicle as well as the jeep compass with same engine are self burping systems. You can squeeze the hoses if you would like but it is not necessary.
@u.s.arepublic6616
Ай бұрын
The radiator bleeder Valve is the in upper left hand corner of facing the radiator. If from the driver seat upper right hand corner.
@davidw1292
5 ай бұрын
If you flush with distilled water, after you drain the radiator you still have about 3 quarts of water in the engine.. if you add 50/50 mix antifreeze, when that mixes in with the distilled water remaining in the engine, it won’t be a 50/50 mix anymore.
@Duk3Silv3r
3 ай бұрын
I was only able to find one bleeder valve, and that was on the radiator. I didn't see one on the core temperature hose. What does that mean?
@gregorithda3rd
4 ай бұрын
very informative and helpful! any chance you could do a video on how to replace the coolant reservoir?
@603Mechanicvids
4 ай бұрын
once I get my hands on another renegade I'll definitely do this
@MilwaukeeMade1995
Ай бұрын
So for the bleeder valves is there a specific name for those
@555_Lady_JB
4 ай бұрын
Hey anyone else's Jeep Renegade run so hot, can't touch hood? I got the engine swap but it's the same multi air engine so it's so dang hot. I'm getting concerned the gauge is rigged to not read accurately..
@bahirraad8617
Жыл бұрын
Is this procedure same for JEEP COMPASS 2019 ?
@airnicholai
Жыл бұрын
Yes. It’s the same engine and for the most part, same components
@michaelhembree3432
Жыл бұрын
What about bleeder valves open when at operating temp would that work
@MotKcelles
6 ай бұрын
Can I use the same brand you used to top off of the oem fluid? I’m just a smidge low from a tiny leak and I currently have a 2019 Jeep Renegade Trailhawk with about 113k on it.
@603Mechanicvids
6 ай бұрын
yes
@eddiev8148
10 ай бұрын
How do I remove the quick connect? Doesn’t seem to budge
@603Mechanicvids
10 ай бұрын
sorry for the late reply but it pulls off very hard
@eddiev8148
10 ай бұрын
@@603Mechanicvids no worries,… feels like it’ll brake haha,… is there a replacement part#? Don’t know what’s it’s called so searching Mopar has been a pain.
@juliogomez7237
Ай бұрын
Patience young grasshopper.....and a lot of pulling .... patiently 😂
@AlialGarOh
3 ай бұрын
Thanks
@fachritriaji4585
Жыл бұрын
I can’t even take the hose off even with the clip off. Any suggestions on what I should do?
@603Mechanicvids
Жыл бұрын
it comes off very hard. you have to try and break it loose by twisting it slightly but be careful not to break it since its plastic.
@albertcampos716
Жыл бұрын
Any video of how to replace radiator
@603Mechanicvids
Жыл бұрын
no not yet
@coreymiller6666
Жыл бұрын
What about air in the system. Did you have to bleed it after you filled it up?
@603Mechanicvids
Жыл бұрын
It had very little, once the thermostat opened up snd fans kicked on it self burped the air out then i just added the coolant needed. I just left the reservoir cover off until it was up to temp
@stevengower
Жыл бұрын
I have 170k on mine never changed should I?
@603Mechanicvids
Жыл бұрын
yes, coolant goes bad overtime, old coolant can start causing corrosion of the cooling system, as well as not cool the engine as well which can be very bad especially if your engine starts overheating. I recommend changing it asap
@juliogomez7237
Ай бұрын
Yes. A long time ago!!!😂
@Space__Rooster
Жыл бұрын
Other than the amount of coolant is this the same process with the 1.4L?
@603Mechanicvids
Жыл бұрын
I've never worked on a 1.4 yet so I'm not sure about that
@Space__Rooster
Жыл бұрын
@@603Mechanicvids no worries I probably should just let a mechanic do it 😁
@anthonyshort9250
Жыл бұрын
Thank You
@overkill677
4 ай бұрын
Why not just use a vacuum filler. Pull a vacuum on the system and suck the coolant back in. Shouldn't have to add anymore coolant after running it.
@issacportillo7428
Жыл бұрын
So I just can’t pour it in?
@603Mechanicvids
Жыл бұрын
you need to open the valves to let air pockets escape while filling with new fluid
@juliogomez7237
Ай бұрын
I assure you it's not quick.!!!😂😂😂
@joerichardcycles69
8 ай бұрын
Watch out . . on high mileage engines, the radiator is weak and will break even if you barley pry on the lower hose . . . There has to be a better place to drain it . . . Now the lower hose couple o-ring is compromised and could leak also . .
Пікірлер: 49