Shop This Barricade Adventure HD Front Bumper: terrain.jp/2L81tRI Subscribe for Daily Jeep Videos: terrain.jp/SubscribeXTyt
@laaganoverland6355
5 жыл бұрын
Hello! Will this work with the non LED package JLUR?
@jnichter4408
10 ай бұрын
Installed this bumper on a 2021 Wrangler Sport JL 2 dr on 9/30/23. Additional tools required: Die Grinder (to enlarge one bolt hole), Gorilla Mounting Putty (to be explained), Rubber Mallet (to center bumper once loosely bolted on), 9" Needle Nose Plyers (to grab bolts when barely fed through hole when attaching bumper) and a very talented mechanic (AKA my boyfriend). Install took about 2 hours including a break due to frustration upon putting the bumper on once the fog lights were in. The stock fog lights fit fine. Lifting the bumper on is when the Gorilla Putty saved us. This is "Step 7" in the included instructions. The "nut/bolt plates" DO NOT STAY IN PLACE. I'm guessing this is why this video goes straight to putting the bumper on. One bolt hole, lower hole, passenger side, did NOT line up hence the Die Grinder. We made it work. The front plastic/stock skid plate will go back on w/ some custom metal plates, the original plastic clips and some cutting to fit. This video was extremely helpful to me. I'm not mechanically inclined, knowledgeable w/ tools and this is my first Jeep. My boyfriend has been a mechanic/engineer since his late teens and has owned numerous Jeeps. Get one of those or have one on speed dial! I wish I could upload a before/after pic b/c I really like this bumper. I researched them quite a bit and am 100% satisfied with this one. Purchased through 4x4 Outfitters. Great customer service and shipped in about 3 days!
@mach5jeep
6 ай бұрын
This is correct. This bumper is an absolute engineering fail. No longer are the studs attached to the bumper. Instead you are given some idiotic stud attached to a blind bolt with nothing to hold it in place while trying to install. So guess what? They fall out every time. The only way I can see to install this is to weld it to the frame.
@SopwithAviator
4 жыл бұрын
Shouldn't the front skid plate have been reinstalled?
@jamesandrews7441
5 жыл бұрын
Ordered this bumper September 2. Installed today. Video was quite a bit off from what the actual install consisted of. She shows using those chips for the fog light screws. No. This one had a bracket on each side to install and use these little screws and try with your fingers to hold the not underneath it and tighten them down. Very frustrating. Second the bumper required some hokey brackets using plastic threaded cards to keep them in place while mounting the bumper to the frame. Took 2 people to keep everything aligned and from those bolt brackets and bolts from flopping around too much to get them into the front frame holes. Took 3 attempts. Either this video shows an upgraded bumper which is I thought I was ordering and I got an older type of design. Wasn't too happy with the install. Not like portrayed here. It looks very nice on the Jeep now but took double the time it should of. I give it a 2 out of 3 stars on the install rating. Buyer beware.
@Jayhowell72
5 жыл бұрын
I just went through the same thing you did. For my fog brackets, one wouldn't even go in. Had to bore it out and use a nut and bolt. The brackets for the bumper were a pain on mine as well. I managed to get 7 of them in, one will not go no matter what, oh well. I did manage to use a motorcycle lift to jack it up while I lined it up, that made it a little easier but it was nothing like this video.
@jamesandrews7441
5 жыл бұрын
@@Jayhowell72 sounds like we're not the only ones that have had this issue. Extreme terrain should either take down this video or put it the way that it actually installs.
@DChomsy
4 жыл бұрын
Damn, I'll go through all this tomorrow when bumper arrives. The video eo made it seem so easy, but from reviews its gonna be a challenge i see.
@gs98999
4 жыл бұрын
You guys must have gotten the JK bumper as shown here: kzitem.info/news/bejne/2nuhs22mr6phmII go to 7:46 of that vid I would like to order this bumper for my JL. However I would like to know I am getting the bumper shown in this Video (One Merideth is installing) because I'm all the way in Canada and don't feel like shipping the JK bumper back is a cheap option if I get the wrong one.
@mountainknife
4 жыл бұрын
Wow. Nice rear bumper on that rig.
@BiO811HazarD
5 жыл бұрын
Love the in depth installation. Wish all the old JK videos were this in depth!
@booboogaloo2152
2 жыл бұрын
Oh hell no way I’m going through all that much work!! You gotta be nuts!! Where can I get an installer in Dallas to do this?
@jreilly2413
6 жыл бұрын
I noticed three changes of nail polish color. Just an observation. Well done regardless. I'll be replacing mine tonight.
@stevereid9913
4 жыл бұрын
Replacing your bumper or your nail polish color?
@crissypooh7345
3 жыл бұрын
I got the same bumper for my 2020 unlimited sport s but my fogs have 3 point instead of 4...what kind of bracket do I need to make the fogs work with this bumper
@rwagner1978
Жыл бұрын
This bumper has changed a lot since this video. For starters, this bumper does not work with OEM LED fog lights from a factory steel bumper. The allen head screws used for the fog lamp bracket aren't great because the bumper is sprayed after assembly, and the screw holes are covered in coating. Ended up going with 7mm bolts instead of the screws. The actual install is pretty simple but the bolt/mounts are not welded on they are four pieces (one bolt, one nut on each) so highly recommend you have a second set of hands around to help you out. If you don't you'll constantly be taking the bumper off to try to realign the bolts, as they float around in the mounting plate. The fit, once on, is great and the bumper is relatively light. Biggest gripe was the instructions are terrible, almost not worth reading because they blend JK/JL together as if the two are identical. You will not be using the mounting hardware from your old bumper (if replacing an OEM steel bumper on a JL), so keep that in mind because it isn't called out. I was happy with the overall build quality but it is somewhat silly there isn't a skid plate for this bumper.
@gs98999
4 жыл бұрын
So I ordered a JL and got the JK version. They say it’s the same thing on the phone. I will watch the JK video and go from there, but it would be much nicer if when you place an order in this video link you got this bumper version, as it seems quite a bit easier to put in.
@gcjctc2
6 жыл бұрын
Great video, now come and install mine!
@dunnoyolo2238
23 күн бұрын
It’s awesome watching you do installs wish more women were like you 😊
@extremeterrain
21 күн бұрын
Thank you! 😊-Merideth
@parkersmith4551
6 жыл бұрын
I liked that a woman installed this. It gives a better sense to the weight of the bumper, honestly. Smart choice when weight is a serious consideration for daily-drivers.
@Heartlanddualsport
6 жыл бұрын
Sweet, thanks for sharing this with us and I hope you have a blessed week.
@Dustin-Holstein
6 жыл бұрын
I put this bumper on my JL Rubicon and I do not have the LED package. My fog lights fit perfectly. On the product page, my jeep is the silver one with the red fairlead if you dont believe me.
@gblades5618
6 жыл бұрын
Dustin Holstein Please share how you did it...I'm stuck!
@Dustin-Holstein
6 жыл бұрын
My fog lights lined up with the holes on the new steel bumper. No modification was needed. I thought I would have to drill new holes on the bumper/make a new bracket to mount them but to my surprise, I just popped in the plastic inserts and my OEM fog lights bolted right in. I was looking forward to making a project out of it but I got my time back instead... Perhaps they offer two types of halogen fog lights depending on the bumper? I did not opt for the factory steel bumper when I picked mine up because I knew I would be replacing the bumper anyway.
@Perfektliflawedd
5 жыл бұрын
Yeah except they changed the bumper, and now it’s almost impossible to line up the damn bolts with the frame.
@sergiom9159
5 жыл бұрын
Nikki, so were you able to install bumper at all ? I was thinking about getting this one.
@My-tk1oj
5 жыл бұрын
Fucking yes! Just installed mine, and it was NOT this simple! It come with 4 odd bolts that you have to line up inside of a hole but the only opening is pressed up against the frame so if you drop one while trying to line up you have to completely take off
@narssasisticasshole3255
5 жыл бұрын
Ok it's not that simple installing the bumper , I got the one with a light bar , no instructions at all, the screws in the box are not the ones to mount it , and the alignment is a bitch it on. Some of the screws for OEM lights to be put in had issues.
@michealcorleone665
5 жыл бұрын
im trying to line my bumper right now 😂 my back hurts from so many attempts
@My-tk1oj
5 жыл бұрын
@@michealcorleone665 definitely are going to need a second person
@andymartes2501
5 жыл бұрын
Did she just change nail colors ?
@palewindtv
3 жыл бұрын
Tried ordering this and following this video. Got all the way to the end until it was time to insert the fog lights before I realized you guys shipped me a JK bumper and not a JL version that I ordered. Fog light brackets are not correct and not the right mounting hardware for the final two steps. Incredibly frustrating!
@goyo69
6 жыл бұрын
Hey Merideth do you have a twin? Because when you were removing the fog light harness you had or your "twin" had different nail polish! Lol. Just curious! Great videos!
@jackebagbaga1475
5 жыл бұрын
It was the boyfriend who had removed the second time
@pas84av2
Жыл бұрын
Can I use the wiring harness from the halogen fog lights for aftermarket or OEM LED fog lights?
@MrJesu84
5 жыл бұрын
Nice
@DChomsy
4 жыл бұрын
wish mine had retaining clips for the fog lights! The bumper in this video is not the same when it comes to hardware install. The fog lights are the most difficult when you have to use a modified bracket to align it. The holes have some of the paint all over the threads so the iddy biddy tiny 2.5mm hex key has no torque at all to push past it. Should advise viewers to watch the JK install instead. THey are trying to sell old stock so everybody is getting the outdated bumper with brackets to align. I wouldn't of ordered this when the video is misleading.
@spence524
3 жыл бұрын
Any idea how much further this sticks out than the stock bumper? For a gladiator, I have concerns about my JT fitting in the garage with this bumper.
@TheAmazingGras
3 жыл бұрын
what power tool and bits is she using? sorry not very handy
@ChrisandSohee
6 жыл бұрын
Cool Video, Keep up the good work!
@rickblack8055
Жыл бұрын
my 2018 is different my fog lights can't be mounted or did someone send me the wrong bumper?
@extremeterrain
Жыл бұрын
If you have sport fog lights you can either upgrade to the 4 bolt hole JK/JL option or check out our adapter brackets on the site!
@virgilsmith5792
2 жыл бұрын
Can you flat tow with this bumper? How do I contact EAG?
@2asianguys667
3 жыл бұрын
She can install this better than everyone on this comment.
@joshcarlisle4901
4 жыл бұрын
does the same model fit both the JL and the JK?
@phillipcraggs6202
6 жыл бұрын
Is there a filler plate to cover the winch area? And what do you do if one does not have the LED package?
@Dustin-Holstein
6 жыл бұрын
I put this bumper on my JL Rubicon and I do not have the LED package. I am not sure why they specified the LED fog lights because I dont have them and it fit perfectly. On the product page, My jeep is the silver one with the red fairlead.
@ThatguyTrevor
4 жыл бұрын
Phillip Craggs get a winch anyways!
@M.L.Knotts
2 жыл бұрын
It's $430 not $270
@atlantis7896
5 жыл бұрын
how heavy is this bumper
@robertkeefer2128
4 жыл бұрын
What bumper?
@NextGreatLegend
6 жыл бұрын
So if you don’t have LED package what happens?
@redsyphon
6 жыл бұрын
John Covacci, apparently the halogen fogs mounting points are different. So, the mounting holes won't line up. I heard somewhere that you could trim the non-led brackets to allow them to mount to the led design, but I'm not willing to spend $300 to find out.
@Dustin-Holstein
6 жыл бұрын
I put this bumper on my JL Rubicon and I do not have the LED package. I am not sure why they specified the LED fog lights because I dont have them and it fit perfectly. On the product page, My jeep is the silver one with the red fairlead.
@CJ-jh9ri
5 жыл бұрын
Dustin Holstein Did the mounts and everything line up? I want to grab this but I have the Sport with the halogen fog lights.
@ofcmiller1340
6 жыл бұрын
The standard fog light bracket on the new JLU Sport do not work on this bumper so there is no way to move your JLU Sport fog lamps to this bumper. TOTAL WASTE of the fog lights. And the printed directions are for a JK, totally useless. This video is helpful even though the back plastic part of the bumper is nothing like my JLU Sport bumper.
@DRockDreamin
Жыл бұрын
Took me 4 hours because of the stupid fog light screws and the large bolts were too short to use the crush washer. Pissed me right off.... parts didnt even match the video and the instructions were a joke. Literally stopped giving steps after mounting the fog light. Pissed!
@durtyred86
Жыл бұрын
.......Did she say $270??? Funny, I just purchased this as a gift for my ladies Bday, but it ram around $400ish... 😮💨 Can I get the 2019 price back, please...😅
@LM-ed7rt
4 жыл бұрын
The inside build of this bumper is NOT what ExtremeTerrain sends when you order the JL Barricade Adventure HD Front Bumper (J107329-JL). So the install of the bumper is not as easy as it looks in this video. I have tried to explain this, and four calls later, I'm getting nowhere. What you get is the JK bumper with adapter brackets that are in the video for installation of the JK Barricade Adventure HD Front Bumper (J107329). Compare this bumper at 8:37 to 4:31 in the video of what ExtremeTerrain sends when you order the JL bumper in this video: kzitem.info/news/bejne/2nuhs22mr6phmII
@DChomsy
4 жыл бұрын
Thank you for this. This video has no mention of all the extra hardware you receive a d where they go.
@DChomsy
4 жыл бұрын
Same situation here; total BS! They know that 99% of the customers will not return the bumper. Seems like they are depleting old inventory from the JK version, so we get brackets to align the fog lights.
@smoscar
3 жыл бұрын
@@DChomsy does it fit with the included mounts? trying to avoid a return here
@sQriLLah
3 жыл бұрын
@@smoscar yes it fits, but you gotta be very meticulous and flexible fingers. The tiny nut you have to hold and align blindside in a hidden area is near impossible. I was able to do it after 100 times of dropping the nut. Also thought about just drilling a hole and making my own holding area. You'll know if you got the JK version or JL, when you check status of order and it will say JK version. Pray that you get the JL version (no bracket hardware needed) you know the one that everyone thought they ordered.
@smoscar
3 жыл бұрын
@@sQriLLah nope, I got the JK one. I installed it last weekend and it was a pain in the ass.
@tacomax7183
5 жыл бұрын
U got a nice bumper women🤔😳
@chriscarter1256
6 жыл бұрын
Every new model makes them more and more complicated to work on
@robertprice9052
4 жыл бұрын
I have a 79' CJ5 and a 2019 JL, you are very right about that!
@AnthonyM1
5 жыл бұрын
@270.00??........404.00 at the moment
@extremeterrain
5 жыл бұрын
Sorry about the confusion! This video was made over a year ago and unfortunately due to inflation and new tariffs, prices have gone up a bit. Thanks for watching! -Zach
@AnthonyM1
5 жыл бұрын
@@extremeterrain NP, but I think instead of companies stating tariffs are hurting them......it's more like hurting the customer.
Пікірлер: 80