If you are able to raise the Jeeps front end up and place the frame on jack stands it is much easier. It allows the axle and steering assy to fall just a bit and giving you more hand room. Just my 2 cents.
@JeepSolid
6 жыл бұрын
Good tip. Thx!
@stevediy963
3 жыл бұрын
Would really be helpful if they covered the floating rear portion of the gasket that goes into the grooves on the crankshaft bearing retainer.
@gpomeroy
5 жыл бұрын
where would be the best place to tap a hole and place a Threaded Immersion Oil Pan Heater with five inch long element?
@PaulinaRudy
Жыл бұрын
How long should you wait to turn on or even drive the car after you replace the gasket?
@kevinritter4932
Жыл бұрын
My jeep has been sitting for 5 days without the oil pan on. Do i need to prime the engine before i start it up after the pans back on?
@JeepSolid
Жыл бұрын
It should be fine.
@caitlinbarrett8451
5 жыл бұрын
Were there any special sealants needed when putting the new gasket on?
@JeepSolid
5 жыл бұрын
I used a little RTV on the corners
@TheDasboot11
6 жыл бұрын
I just got a yj 4.0. Seal looks brand new but looks to be leaking right in the from the the oil pan. I wonder if thet didnt use any rtv on the corners. Also seems like its sticking out too much in the front
@JeepSolid
6 жыл бұрын
Yeah. Both are possible. Gasket may have slipped when they installed it.
@ishikawa1338
5 жыл бұрын
Try tightening thrm a bit
@Muttaqi757
3 жыл бұрын
Did you have a leak? If so did this fix it?
@JeepSolid
3 жыл бұрын
Yep. And yep
@Mark622111
4 жыл бұрын
I'm really thinking about replacing my oil pump per one of your videos. I have 40 psi at higher rpms and around 8-13 at idle. My project is a 1997 Wrangler TJ with 198,000 miles. Going for 250K before I drop in a crate engine, I don't have your skill sets to rebuild the one that's in it now, but will keep the core just for the adventure of a rebuild kit. My question is, do you or one of your viewers know what the oil pressure should be at idle on a 4.0L inline six. FYI, I replaced the sensor and did a manual gauge check, which all agree....40 psi at road speed / 8-13 at idle. Last question and I'll shut up. My Wrangler TJ has a 3" lift...do I need to remove the exhaust piping in order to remove the pan?
@franmitch3589
4 жыл бұрын
Mark Gaarz 15 to 20 is not uncommon considering oil weight temperature and so on I know its low but worn engines do lug excessively creating lack of pressure also tolerances are no longer as tight but dont fret I've personally ran one 2.5 four cylinder and the 4.0 with little to no oil pressure heck I even ran the 6 cylinder completely out of oil on a trail once to get home, still running to this day, not healthy but its alive
@krissyg3
9 жыл бұрын
1) did you drain the oil first 2) my jeep is a 2005 jeep grand Cherokee limited 4wd-is the replace the same as this video?
@JeepSolid
9 жыл бұрын
Yep! Must drain oil first. I would imagine the 05 Cherokee is similar, but not sure.
@jimdavidson5208
6 жыл бұрын
NO, you can remove the oil pan without draining. That is an option for you.
@robc5768
4 жыл бұрын
@@jimdavidson5208 it might drop easier with the added weight
@onemat2000
6 жыл бұрын
Is the jeep off the ground in this video?
@JeepSolid
6 жыл бұрын
nope
@tomgiar923
9 жыл бұрын
How long should It take to complete? I plan to do the work in the spring.
@JeepSolid
9 жыл бұрын
Just doing the oil pan is a fairly quick project. I'd give it maybe 2 hours from start to finish.
@weld3z
9 жыл бұрын
I have leak in the oil pan need to replace it ( hard off roading ) can i use XJ oil pan ? They are same engines 4.0 ! the reason why i want XJ oil pan we have many Xj in junk yards and my wrangler is 2006 sahara wrangler
@coltinlaplante7400
5 жыл бұрын
Go take a look and see if they look the same they could be different due to routing exhaust and such
@coltinlaplante7400
5 жыл бұрын
Just realized you posted that 3 years ago did it work?
@jippyflapthorp9486
6 жыл бұрын
If there is a cross member in the way, are there any tips or tricks to get around it?
@malarkeywithmatt2396
5 жыл бұрын
Joshua Booth repair manuals suggest pulling the motor up a couple inches if that’s the case
@coltinlaplante7400
5 жыл бұрын
Did you have to move any of the exhaust or any other parts out of the way for this job?
@JeepSolid
5 жыл бұрын
Didn't have to move anything.
@coltinlaplante7400
5 жыл бұрын
Tha sk for the quick response
@indierocker772
6 жыл бұрын
Anybody know where I can find a whole new set of oil pan bolts for a 4.0L YJ?
@Nitroraccoon
3 жыл бұрын
Ace hardware go in and get 25 1/4 20 thread and 4 5/16 match Length to original
@joseescobar8104
8 жыл бұрын
did you have to remove any suspension components?
@JeepSolid
8 жыл бұрын
+jose escobar Nope. This jeep has a 3.5" lift, which gives me some extra room.
@jasoncostanza5580
Жыл бұрын
How did you get the exhaust out of the way. Having all kinds of hell removing mine. Damn engineers at a desk with a CAD drawing on a computer need to be kicked in the head
@alejandronava6442
8 жыл бұрын
you had to remove the pipe and the starter to get to the pan right?
@JeepSolid
8 жыл бұрын
Not on this 95 4.0L Wrangler. Did not have to remove them to get the pan off. But, on some other engines and models, yep you have to remove them. Here's a video of the same job on a Cherokee. Was a huge pain to get the pan off. Similar to what you explain. kzitem.info/news/bejne/14eKx5OYjqCjkn4
@mort3770
5 жыл бұрын
Wow, just saw this video! You never know how helpful a video will be. Pay attention at the two min, twenty second mark of the video linked below. kzitem.info/news/bejne/mJWqromlgaNiiWk
@JeepSolid
5 жыл бұрын
Oh man!!! That is so cool!! Thank you for sharing this. That's my #1 reason for working on all these videos. I love helping people out with their projects and giving them confidence to do it themselves. Thanks!
@brandoncdurham
2 жыл бұрын
Worst video EVER.. Dude just stopped the video as he's putting it back on. haha
Пікірлер: 42