That music was painfull, but great job explaining the process - much appreciated.
@dimesdailymetalcraftddmc8461
Жыл бұрын
Haha. I know right. I am not good at editing and I’m far from a KZitemr. I’d like to put my own music in but I’m only working with iMovie to piece it together. Not many music options. Haha
@marcossilva7301
Жыл бұрын
Oi meu nome é Marco gostei muito da construção da sua embarcação sou de São paulo Brasil futuramente vou fazê um também vou tentar fazê semelhante o seu abraço
@bravopescaeagro647
11 ай бұрын
Você tem um projeto pra um barco 6 metros , tenho sonho de construir um
@anekakarya5977
Ай бұрын
Panjang dan lebarnya brp bosq
@klac1024
Жыл бұрын
A little off topic on this build, but am curious about what you think of the performance of your 10' Headwater and if there are any real downsides other than maybe the size.
@dimesdailymetalcraftddmc8461
Жыл бұрын
The 10’ is awesome. Super light. Very maneuverable. Only things I hated was if you stand up to drive it so you can see big rocks you are hunched over like crazy. There’s no room to put your feet while doing so. If your standing up and you want to turn around I found there’s no room for your feet to spin around. I’m only a size 10 too. And if you don’t have full range from your trim to point down you Will porpoise all the time. Only way to correct it is to be in a constant semi turn
@klac1024
Жыл бұрын
Thank you
@dimesdailymetalcraftddmc8461
Жыл бұрын
No problem.
@signled1215
Жыл бұрын
想购买图纸
@marcossilva7301
Жыл бұрын
Oi é o Marcos novamente gostaria de saber qual a espessura da chapa usada é de 3,5 mm ou 4.00 mm
@dimesdailymetalcraftddmc8461
Жыл бұрын
The hull bottom is 1/4” 5086 aluminum the stringers and centre inlay is 1/5” 5052. Everything else is 1/8 5052 aluminum
@marcossilva7301
Жыл бұрын
Legal Amigo muito gentil da sua parte ter me respondido e depois de tudo pronto você vai postar um vídeo déla correndo dentro dágua? garanto que todos estamos ansiosos pra vê abraço até mais
@dimesdailymetalcraftddmc8461
Жыл бұрын
Oh yes I will be forsure. This will be a full turn key build video series then yes. To ripping up the river. Thanks for your support my friend
@impuls00007
Жыл бұрын
Where can I find cnc files and drawings???
@dimesdailymetalcraftddmc8461
Жыл бұрын
Jet stream won’t sell their files. And trust me. I templated a boat and built from scratch before. There’s not a lot of savings. Buying the kit is the way to go
@marcossilva7301
Жыл бұрын
Amigo você disse que já fez um barco antes? poderia me dar imas dicas de cortes para o fundo e laterais? se poder te passo meu email obrigado.
@bryanturner683
Жыл бұрын
He is probably right about just buying the kit, but..... If thats not practical you can do a search for. "Specmarine" or "Specialty Marine" . They are Portland Or area and do CNC plans for aluminum boats. Dont know if they have any mini boat plans but they might and if not may do a layout for you. boat least one place in Portland that can cut for you. Good luck. Im hoping to do a 22' boat and have will check them out when I get ready. They have more plans than what they show on their website.
Пікірлер: 19