Prolly why my fuel mileage sucks lol. Oxygenated race fuel can be pretty hard on seals. And unfortunately the quad sits way to much. I'll be looking into this in the spring. Thanks for pointing this out
@Trap..house.
2 жыл бұрын
Thank you 🙏💪running a 178 /48 with 3 turns out in fuel screw Bike is running amazing! 04 yfz450 Open air box with gyt air filter kit Hot cam cams Full fmf exhaust Running 91 pump gas
@FullSpeedImpulse
2 жыл бұрын
Nice that's a good set up. You ever replace your thumb throttle for a Hondas? You won't regret it!
@Trap..house.
2 жыл бұрын
@@FullSpeedImpulse just ordered one ! Thank you for the videos brotha they help so much !
@loststallz8893
2 жыл бұрын
What was the issue with it before ?
@Peedarb
2 жыл бұрын
Same
@robertmartinez3354
Жыл бұрын
Will this setup work with a full empire exhaust on a 07? Yfz450
@jesussilva791
2 жыл бұрын
Also I give it throttle and it takes a while to take off it has a fmf header and a big gun exhaust
@nate4036
Жыл бұрын
On my 08 YZ450, I’m running a Boyesen Quickshot 3 and still using the zip tie mod…. It’ll squirt fuel all the way to valves with no issues 😂
@450Braden
9 ай бұрын
I’m running a hmf slip on, stock airbox and intake, uni filter, k&N power lid and zip tie mod. Jetted to 172M 48P and needle is set 4th down from top. Air/fuel screw is 2 turns and it’s running very lean and bogs on bottom end and also backfired on deceleration. I’m at 800-900ft
@FullSpeedImpulse
9 ай бұрын
Yea I would bump your main up to 178 and see how it runs. 172 is a little on the light side.
@garretthaynes6585
Жыл бұрын
I have 05 yfz450 ported head lid on air box gytr exhaust aftermarket filter 45 pilot and 170 main starts and idles good but it has a slight bog half to full if it’s stabbed a bit I’m at 1200 elevation and it’s around 90-100 degrees everyday
@FullSpeedImpulse
Жыл бұрын
I would try bumping your main jet up to a 175 and see how she runs with that
@wilfredosanabria5348
2 жыл бұрын
Hey bud i have a 2005yfz 450 carb model with full Empire exhaust Big bore kit and kibblewhite valves florida elevation what would be a good jetting
@FullSpeedImpulse
2 жыл бұрын
Dang I heard those empire exhausts are pretty nice. Never ran one though. What size big bore you running?
@edwardrodriguez8846
Ай бұрын
i got an 08 yfz450, it comes down slow from a rev , it has a full empire exhaust and jetting done along with a quick shot. It does pop a bit aswell on decel
@FullSpeedImpulse
Ай бұрын
Definitely sounds lean. What’s your jet size?
@edwardrodriguez8846
Ай бұрын
it’s got a 168 main & 48 pilot airbox lid off
@edwardrodriguez8846
Ай бұрын
i’m at 600-800 elevation
@edwardrodriguez8846
Ай бұрын
@@FullSpeedImpulseaswell as stage 2 cams
@FullSpeedImpulse
29 күн бұрын
I’d throw a 178 main in and see what it does. Make sure you dial in that air/fuel screw too.
@javiertorrez3962
11 ай бұрын
Hello what u recommend for main jet n pilot for a 07 yfz450 casa full exhaust uni air filter and open air box
@FullSpeedImpulse
11 ай бұрын
What’s your elevation bud?
@jordanmolinaro6507
Жыл бұрын
I have an 08 450 limited edition, stock carb, stock exhaust for now, what would you recommend for a jetting setup if I'm just running 93oct on that setup? Also I had the carb apart the other day, there's 3 jets, the main jet in the middle, the pilot above it but what is the 3rd jet off to the bottom left? Is it another pilot or something else?
@FullSpeedImpulse
Жыл бұрын
3rd jet is called a leak jet. Shouldn’t have to mess with that. Is it not running good with the stock jets in it now? And what’s your elevation?
@Ron2195sue
Ай бұрын
I have a 2013 yfz with a stock carb and full aftermarket exhaust. Currently running a 147.5 and a 55 at 1200ft above. What would you recommend as a good mid range for larger jets? Non adjustable needle.
@FullSpeedImpulse
Ай бұрын
You have the airbox lid off or on? What’s it doing now? Low/rough idle and popping on the top end?
@ghhbjhfygcb6946
2 жыл бұрын
I got a 2008 yfz 450 every time I hit the throttle it cut off will this help out or should I just clean my carb
@FullSpeedImpulse
2 жыл бұрын
Yep sounds like you need a good carb cleaning for sure. Make sure you have a good spark plug and a clean airfilter also.
@eastonavery2697
5 ай бұрын
I've got a 2004 yfz 450 and I've got stage 3 hot cams and 13:5:1 piston and full exhaust and open intake and I'm running a 168 main and a 48 pilot and the needle on the 3rd clip and it runs great but its a pain to get it started and I'm running 110 fuel and my elevation is 1000 feet
@FullSpeedImpulse
5 ай бұрын
Have you tried adjusting your air fuel screw at all? Going to be way easier if you have a quick adjust on there
@tylerharper5330
2 жыл бұрын
Hey what’s going on I have a 06 yfz 450 i just bought Ik the bike has air box lid off with filter slip on exhaust and cams but I don’t know what kind it has 175 main and 50 pilot how many turn would you go out on the screw my elevation is 121
@FullSpeedImpulse
2 жыл бұрын
You should usually be at a turn and half or so if jetted right. You will be able to tell by how high it idles. Not enough turns or too many and it won't idle. Find that happy spot. Then adjust your idle afterwards. Does it idle good and have good response?
@JumpManJohn
Жыл бұрын
i know this video is a little old but i just bought a 2005 yfz 450 and its got a je high compresion piston and i cant get the jetting right any tips
@FullSpeedImpulse
Жыл бұрын
What all is done to it? Exhaust? Open air box?
@jesussilva791
2 жыл бұрын
I just bought a yfz450 it’s a 2007 carb model as I was riding it seemed to pop a lot from 2-3 the power is there just seems like it can run alot better any tips ?
@FullSpeedImpulse
2 жыл бұрын
Well I would first start by seeing what jets are in your quad. I believe fmf has a chart for your fourwheeler on what it should be jetted at. Higher you are the leaner you will jet. And at elevation like that power loss is to be expected. Look into the ziptie mod. This could help on some of the hesitation.
@FullSpeedImpulse
2 жыл бұрын
When I say you would jet leaner what I mean is you would jet leaner then someone at a lower elevation. It sounds like you might need to go richer still possibly.
@kurtlasee293
Жыл бұрын
Just figured Id get your input just got a 2005 450 it backfires slot shoots flames and bogs out and dies underload at max throttle waiting on jets to get here I dropped needle down to 5th notch and it has 45 pilot and 168 main was thinking of going to 48 pilot and maybe 180 main your thoughts. And I have full two brothers exhaust and open air box. Elevation 1000 ft
@FullSpeedImpulse
Жыл бұрын
I’d go 176-178 and 48 for the pilot sounds good
@kurtlasee293
Жыл бұрын
@@FullSpeedImpulse yeah I put a 50 pilot 175 main new rectifier and still once she gets to half to 3/4 throttle its like it's hitting false rev limiter
@kurtlasee293
Жыл бұрын
Also I had to jump my battery it's dead so that also could be part of my problem is just junk not enough juice to magneto
@FullSpeedImpulse
Жыл бұрын
Replacing the battery would be a good start, but not necessarily your problem. I’ve had what seemed like a bad battery causing issues. But unsure if that was the actual problem. Your dirtbikes without electric start don’t have batteries. So I wonder…
@450playyer
Жыл бұрын
I got a 2004 yfz450 and running not so good port n polished head,stage 3 cams,13:1 piston,stroker crank and fci intake and runs on 110 with a 215 main and 72 pilot idles fine but doesn’t rev out and back fires a lot located in Maryland USA thoughts?
@FullSpeedImpulse
Жыл бұрын
I think you might be jetted to rich. Your elevation is pretty high and those are some spicy jets. The only reason my jets are so big is because of oxygenated fuel. I’m curious, How did you end up with that jet sizes?
@450playyer
Жыл бұрын
@@FullSpeedImpulse even with a 200 main and 55 pilot it was still running like shit and I just checked the plug today and it is a gray color inside and almost a little darker on the outside of the plug
@bobbyboyle8893
10 ай бұрын
When I rev my 450 up it pops when I let off the throttle or when I'm ripping and let up off the throttle it pops so does that mean it's to lean
@FullSpeedImpulse
10 ай бұрын
Yes sir!
@jorgec1417
9 ай бұрын
Any recommendation for jetting on 04 yfz w dasa full exhaust n fci intake no box at sea level
@FullSpeedImpulse
9 ай бұрын
Try a 50/180. I would normally say 48/178. But you are a little lower in elevation so you will need to jet richer
@jorgec1417
9 ай бұрын
@@FullSpeedImpulse thank you how bout the needle clip. I got the ncvq as well
@FullSpeedImpulse
9 ай бұрын
@jorgec1417 I would start closer to the bottom and work your way up if it’s to rich. The lower on the needle the richer the bike between 1/4 and 3/4 throttle(mid range)
@jorgec1417
9 ай бұрын
@@FullSpeedImpulse i will try it out hopefully it works Thank you sir
@xxbuzzkillxx2503
Жыл бұрын
So I have a 2006 Yamaha yfz450 I just had the valves done air filter and carb clean it spits and sputters I changed the jets because it's all stock with a big gun exhaust I changed it to a 175 main and a 48 pilot but it still spits and sputters how can I fix it I don't know what todo
@FullSpeedImpulse
Жыл бұрын
Well shoot. First thing I would say I guess is make sure all your boots are snug around the carb and intake. I assume when you say spit and sputters it sounds inoperable. Make sure your air fuel screw is dialed in good. Check your plug for readings. If all that looks good. Might have to double back make sure timing is good on the motor along with double check the valves and compression. ALSO if you messed with any of your throttle adjustments on the right side of the carb make sure you didn’t throw off your quickshot. That will cause a huge hesitation or sputtering when you try to goose the throttle quickly. Hope some of this helps.
@joewarnerky
Жыл бұрын
Great video man. You helped my buddy Reed a bunch and I’m hoping you can help me. I have a 2008 YFZ 450. 478cc 98mm big bore. Stock crank. 12.75:1 piston. 93 pump gas. 500 elevation. What jets do I need? Not sure what’s in the bike now but it is very lean. Will not idle down no matter what. Thanks man!!
@FullSpeedImpulse
Жыл бұрын
Do you know what you have in it now for jets? And are you running a open air box?
@joewarnerky
Жыл бұрын
@@FullSpeedImpulse I believe I have a 175 and 48. Factory airbox no lid hi flo filter
@joewarnerky
Жыл бұрын
HMF full exhaust
@FullSpeedImpulse
Жыл бұрын
You can try something around a 52 pilot with a 185 main. That’s a good bump up so should see sometime of improvement. Let us know where you end up!
@joewarnerky
Жыл бұрын
@@FullSpeedImpulse I ordered and installed the main and pilot you recommended. The bike still has a hard time starting, have to hold throttle every which way to get it to start. Does seem to idle okay, not revving high like it was before. But as soon as I snap the throttle it bogs or dies. If I slowly roll into the throttle it will rev.
@markoakley5540
7 ай бұрын
I’ve got a 08 yfz450 just put it together 480cc big bore 13:1 compression running on 110 race fuel new carb from bpratv no air box lid factory box k&n filter sparks race core full exhaust dynatek cdi stock bottom end stock cams jetted it 175m and 48p at 600ft elevation it’s got good power through whole throttle range but it doesn’t want to idle with idle screw turned all way in it barely idles backfires on deceleration noticed pipe turning cherry red think af screw is in stock position and haven’t looked at needle to see if it’s adjustable where would you start thinking maybe bump up pilot to 52 and possibly main to 178
@FullSpeedImpulse
7 ай бұрын
Okay. So first. It’s weird it won’t idle, if you mean like it keeps stalling. Now if it idling really high that would make sense. Your definitely lean. I would take your main all the way to 185. You can try a 52. Make sure you dial in that air fuel screw on the bottom too.
@vincentdyas4063
7 ай бұрын
My yfz is bucking at quarter throttle and top end
@ccoder07
Ай бұрын
got a 06 yfz450, full dasa and FCI intake. has trouble running in colder temps and doesn’t feel as quick and around 1/4 throttle. any tips ?
@FullSpeedImpulse
Ай бұрын
I would say bigger jets and maybe different clip position. The colder it is outside the bigger the jets you need. That’s why for the average person. It’s good to jet somewhere in between temps in your region so you have a little flexibility if it gets warmer or colder. What jets you running?
@ccoder07
Ай бұрын
@@FullSpeedImpulse honestly have no clue which jets it has right now. just bought it last night. what jets do you think would be optimal to run for all year round michigan weather ?
@James-nt4yd
2 жыл бұрын
Dang what mods are you running that require massive jets? Btw those Dasa sound mean! I have a Monster shorty but mught get a Dasa soon.
@FullSpeedImpulse
2 жыл бұрын
We definitely got some mods on her. But the big thing is running oxygenated fuel. I'm about to pull her out storage and I'll do a video explaining oxygenated fuel. But man can you tell the difference
@James-nt4yd
2 жыл бұрын
@@FullSpeedImpulse What kind of head work and compression do you have on it? I bet that oxigenated fuel is $$$ but worth it. These carbed yfz’s pull hard I love them.
@FullSpeedImpulse
2 жыл бұрын
Had a local guy do a port job on the head. Hot cams. 14:1 compression. Carbs been modified and bored out. Gytr rev box. Air intake, no filter box. Dasa exhaust. Stock bottom end and bore. Once this build pops we will go big for sure.
@FullSpeedImpulse
2 жыл бұрын
The fuel I run is 116 oxygenated Dragon fuel a local guy sells it. U4.4 vp is good oxygenated fuel if you don't need a high octane. Honestly once your paying for race fuel price oxygenated is not that much more. Just make sure you rejet!
@SpecOpsGear
22 күн бұрын
Race gas
@BigHerc337
Жыл бұрын
Can you help me ?? I live in south Louisiana. I have a 2007 yfz450 with a spark racing exhaust , open air box. My bike was doing how your bike was doing when you first tried to start it but mine is just not starting all the way up . I was running a 170 main/ 42 pilot/ 90 started jet.
@FullSpeedImpulse
Жыл бұрын
Try a 48/178 and see if it gets any better. That sounds super lean.
@BigHerc337
Жыл бұрын
@@FullSpeedImpulse okay thanks I will let you know how it goes
@AidenElliott-zn9vp
Ай бұрын
I’ve got a 2006 yfz 450 that I bought that is completely stock and I’m having issues with getting it to idle and start. I just cleaned the carb. Every time I start to crank on it it backfires decently loudly like a gunshot what do you recommend for the pilot and main and the air screw that I have 2 turns out at 650 elevation
@FullSpeedImpulse
29 күн бұрын
I’d start by bumping up your jetting for the pilot and main 2 sizes. Richening it up will make it easier starting for you. Depending on how many hours it has on it. It might be time to check the valves.
@FullSpeedImpulse
29 күн бұрын
Have you owned a 450 before?
@AidenElliott-zn9vp
26 күн бұрын
Right now it has a 165 main and a 48 pilot and no this is my first 450. It’s gotten a new top end I’m guessing it’s stock.
@AidenElliott-zn9vp
26 күн бұрын
I should mention this also when I first got it and I fixed all the electrical issues with it aka bought a new harness I got it to start and no where near idle but it would actually run if you stayed on the gas once you let go itd die and now that I’ve cleaned it I got only backfire
@jaco7963
2 жыл бұрын
Hi my 2005 yfz 450 backfires on decel also header glows red after just a few minutes of riding, I have a open airbox with k&n filter with gytr exhaust. I'm running a 170 main with a 48 pilot you have any suggestions?
@jaco7963
2 жыл бұрын
Also 2 1/2 on fuel screw
@FullSpeedImpulse
2 жыл бұрын
I'd try bumping up your main a little bit. Also make sure the carb boot is seated correctly
@jaco7963
2 жыл бұрын
@@FullSpeedImpulse ok I will try that! Thanks for the reply 👍
@colesampson9016
2 жыл бұрын
2005 yfz 450, newfoundland Canada, Not sure about the header but my yfz has a gytr exhaust and I don't know if thats causing it to run lean or not but I get a lot of back fire and I notice the throttle response is a little boggy sometimes, any suggestions on jetting? Thanks
@colesampson9016
2 жыл бұрын
Rich*
@colesampson9016
2 жыл бұрын
On the bottom end
@FullSpeedImpulse
2 жыл бұрын
Running a a better exhaust would cause it to run more lean then rich. Pilot jet prolly needs adjusted. Open air box or still have the lid on?
@colesampson9016
2 жыл бұрын
Open air box
@FullSpeedImpulse
2 жыл бұрын
Yea i would say unless someone has messed with the jetting already I would say it definitely needs to be jetted richer. At elevation 800ft I always suggest around a 48/178. If you are higher you will lean those numbers out. If lower you go richer. Alot of those gytr pipes are slip on exhausts I believe. What's your elevation?
@tfelderjr6684
Жыл бұрын
Whats the best way to contact you for help with tuning. 06 yfz450, 500 big bore. open airbox. Full sparks exhaust
@FullSpeedImpulse
Жыл бұрын
On here or my instagram. Instagram is full speed impulse
@daveydave9884
Жыл бұрын
Mine idles just like that. I increased the pilot to 50 from 48. Main is 180. That seems to smooth out mid and full . I have exhaust , intake and stage 3 cams. Stock compression. Should I go up on the pilot?
@FullSpeedImpulse
Жыл бұрын
What’s your elevation?
@daveydave9884
Жыл бұрын
@@FullSpeedImpulse sea level
@FullSpeedImpulse
Жыл бұрын
You can try. Is it idling really high? Make sure you don’t have a air leak through the intake boot at all.
@daveydave9884
Жыл бұрын
@@FullSpeedImpulse it’s idling kinda roughy like the one in your video not smooth. If I bring up idle screw then it hangs up once I hit throttle and may or may not come down unless I turn screw out a bit.
@FullSpeedImpulse
Жыл бұрын
Well my main bearing ended up seizing up the crank this year. So that could I been partially my issue I had going on. Lol. The elevation you are at is a little tricky for me to give you exact jetting. Because 50 should be good for that pilot. You can bump it up a little more. But that pretty rich. What fuel are you running?
@gableroux136
2 ай бұрын
how many turns out? both idle screw and air fuel screw?
@FullSpeedImpulse
2 ай бұрын
That will all depend on your setup
@gableroux136
2 ай бұрын
@@FullSpeedImpulse Meant for yours, just for an Idea, i've got similar specs, just wanted to compare.
@FullSpeedImpulse
2 ай бұрын
@gableroux136 I actually don’t know bud. Currently doesn’t run at all right now. Need to open her up and see what’s going on. Think the crank bearing might be bad
@13window
2 жыл бұрын
What jetting would you recommend,, 2013 yfz450, Mikuni carbd, 6k ft elevation, no air lid?
@FullSpeedImpulse
2 жыл бұрын
Full exhaust or stock?
@FullSpeedImpulse
2 жыл бұрын
6k your way up there. I would definitely start with some milder jetting then my recommended 48/178.
@David-pb1dz
2 жыл бұрын
is the 2013 not fuel injected??
@FullSpeedImpulse
2 жыл бұрын
I believe they made both that year.
@13window
2 жыл бұрын
@@FullSpeedImpulse they made both. Carbed yfzand injected yfzr
@loststallz8893
2 жыл бұрын
I’m glad this video is 3 weeks ago I need help very badly and you described my issue . Do you have Twitter or something I can message you on for advice about the hanging idle ?
@FullSpeedImpulse
2 жыл бұрын
Instagram! If no air leaks in the boot then you need to fatten up your pilot for sure.
@loststallz8893
2 жыл бұрын
@@FullSpeedImpulse your gonna laugh but my jets are stock rn 45 and 155 and I have a big gun exhaust . When I bought the quad the exhaust wasn’t welded together and when I got the exhaust welded it started the hanging idle (I think the previous owner didn’t have it welded to make it run with the new exhaust not sure ). I already got the rejet kit I’m gonna see if 175 will make a difference and 48 . My quad ran best when the air fuel screw was set at 1 if that tell you how bad it needs rejetting . Was just wondering if you would think that rejetting would fix it .
@loststallz8893
2 жыл бұрын
When it wasn’t welded together it ran amazing . I’m wondering if that is what’s making the quad need the bigger jets now ?
@FullSpeedImpulse
2 жыл бұрын
Dang. Lol. It won't hurt! So I'm curious what you welded on your exhaust. Most full exhaust systems are two pieces. And you'd be surprised but alot of them just slip on. Either way that jetting with the airbox lid off should run pretty crisp. Use a 178 if you got one. What's your elevation?
@loststallz8893
2 жыл бұрын
@@FullSpeedImpulse I ended up finding a gash in the boot causing air leak . Ordered a new boot hoping that will fix the problem as it should will keep updated .
@liamlondonmobley
Жыл бұрын
Hey man I got 2007 yfz450 I just put a full hmf exhaust an change my jets to 48 an 170 exhaust is glowing an backfiring any tips?
@FullSpeedImpulse
Жыл бұрын
Bump up your main jet. And at night time it’s common to see your exhaust glow. Specially on the yfz450s
@liamlondonmobley
Жыл бұрын
Alright thanks appreciate you time I’ll try that
@liamlondonmobley
Жыл бұрын
Is it normal for it to turn red after couple min an couple revs ?
@FullSpeedImpulse
Жыл бұрын
@@liamlondonmobley well the backfiring is telling us it’s lean. So jetting the main up should help with that. Once the quad is running how it should I wouldn’t be concerned anymore about the pipe glowing or not.
@bryceriehl6767
Жыл бұрын
Hey I have an 05 and in the process of jetting and can’t get it idel strong it sputters and kills itself and little boggy in top end unless I feather the throttle. Live in pa Have a exhaust with air lid off Pilot: 48 Main:65 Any thoughts
@FullSpeedImpulse
Жыл бұрын
The 165 sounds a little lean for my taste. And if you haven’t already clean your carb. Sounds like you could have a dirty pilot jet or passage. Also make sure your boots are sealed tight between the engine and carb.
@bryceriehl6767
Жыл бұрын
Ok I’ll try that. Also is it a problem that my idle screw is maxed out?
@Gio28419
11 ай бұрын
Man I have tired everything and I just really feel there’s no fixing this cutting up and bog on my yfz. Really needin your help.I’ve got a 2012 yfz450 stock intake with lid on with foam filter stock pipe with a the guy I bought it from didn’t do anything to the bike besides put rear tires on so everything’s stock in it. Whenever the bike is cold it doesn’t cut up or bog but when it gets a little warmer it’ll do it. I have the stock jets which is 105 main and the other is 55 and my elevation is 860 and runnin 89-91 octane gas please what jets do I run to stop this yfz bog
@FullSpeedImpulse
11 ай бұрын
Try doing the ziptie mod on your bike. I do not have a video on it but many people do. It’s suppose to help. I did mine over ten years ago and it’s still good.
@Gio28419
11 ай бұрын
@@FullSpeedImpulse I was gonna do it today but you can’t on the 2012 yfz450s I tried to do it and on the right side of the carb there’s not the things that I seen in the video
@FullSpeedImpulse
11 ай бұрын
@@Gio28419 this isn’t the fuel injected yfz is it?
@Gio28419
11 ай бұрын
@@FullSpeedImpulse no the 2012 yfz450r is fuel injected mines carb model
@Gio28419
11 ай бұрын
@@FullSpeedImpulse I have videos on GoPro of it cutting on it’ll do it under load basically like whenever I go to do a wheelie and pull back up it’ll die out until I let off the gas and at middle of the throttle like mid rpm’s it’ll flutter
@lilboat648
2 жыл бұрын
I just put an hmf slip on, on my 04 yfz 450. Seems to run fine but when I shut the quad off it shoots a flame out the exhaust lol. Is that a sign that I should re jet it?
@FullSpeedImpulse
2 жыл бұрын
I will say that is some sort of sign. Lol. Possibly could need rejetting. Is there anything else it does?
@lilboat648
2 жыл бұрын
@@FullSpeedImpulse not really, and it’s only shot that flame 1 time after I put on the new exhaust, now it seems to be fine
@FullSpeedImpulse
2 жыл бұрын
I'm sure bumping up the jetting a smudge wouldn't hurt. Who knows you might be leaving some horsepower on the table running it too lean.
@jaybee6695
2 жыл бұрын
You cant modify the exhaust or intake without changing jetting. Not good for your motor
@FullSpeedImpulse
2 жыл бұрын
I definitely agree. Even if it does run its prolly leaning the motor out. Only time you can really get away with it is modified end caps or slip on since you still have the stock header restricting the exhaust partially
@gabriellopez8056
Жыл бұрын
i have a 2004 yamaha yfz 450 with a high compression piston, open air box with k &n intake, yoshimura exhaust on 91, it starts fine with the choke on but when i push it back in it dies after a couple of seconds of idling, i’ve cleaned the carb and jets, the carb is all stock do i need bigger jets? or what should i do? adjust air/fuel? it also pops like crazy
@FullSpeedImpulse
Жыл бұрын
Way bigger jets. And what’s your compression on the piston? Anything over 13:1 you have to start running race fuel.
@FullSpeedImpulse
Жыл бұрын
Start with a 48/178 if your elevation is around 600ft
@gabriellopez8056
Жыл бұрын
@@FullSpeedImpulse my elevation is 2300 and the piston is 12:1, i’ll start with getting the jets
@FullSpeedImpulse
Жыл бұрын
Maybe not that big then if your that high up. Maybe a 45/172? But that’s only a guess maybe little less on the main
@gabriellopez8056
Жыл бұрын
@@FullSpeedImpulse i’ll try 45/172 thanks for replying
@cory76954
Жыл бұрын
I have a 500cc Big Bore, +3mm stroker crank I’m in Central KY about 500ft elevation, Open Air Filter and slip on exhaust Factory header. 175 main jet & 48 pilot bike seems to run well do you think I’m safe ? 93 pump gas
@FullSpeedImpulse
Жыл бұрын
Seems like it would be lean. How’s it run?
@cory76954
Жыл бұрын
It’s seem to run fine but definitely sounded like not enough fuel after watching this video. I just don’t want to melt something.
@FullSpeedImpulse
Жыл бұрын
Throw a 185/52 in and see how she acts
@FullSpeedImpulse
Жыл бұрын
Also how do you like the big bore. My motor is finally hurt. Trying to find a big bore that has good reviews seems near impossible
@cory76954
Жыл бұрын
Man it seems okay but I’m to nervous with the tuning to really ride it and feel comfortable but overall the kit seems nice it has a ton of torque
@450playyer
Жыл бұрын
What spark plug are you running?
@FullSpeedImpulse
Жыл бұрын
I’m honestly not sure. Prolly whatever Yamaha recommends because I have never tried changing the heat level of the plug
@grodz6568
Жыл бұрын
Who did the carb boring? Can you send me the info?
@FullSpeedImpulse
Жыл бұрын
I honestly can’t remember. Did some google searching and found someone I liked and sent it out.
@brandonzeller94
Жыл бұрын
What battery are you running , my battery would’ve died before it started
@FullSpeedImpulse
Жыл бұрын
Honestly I run the cheapest battery I can get from Amazon or eBay Lol. Sealed though. I don’t buy the ones you have to fill on your own.
@alexscaggs8406
2 жыл бұрын
BRO i need help my yfz450 us a pain to kick start its a 480cc and it takes like 15 kicks to start i feel like im running lean its a 48p and I think 180 or 178m with the air box lid
@FullSpeedImpulse
2 жыл бұрын
Is there a reason why you don't have electric start?
@alexscaggs8406
2 жыл бұрын
@@FullSpeedImpulse purely because I like having the ability to have a back up to if the battery dies I have had a few starters die on me
@FullSpeedImpulse
2 жыл бұрын
Gotcha. Is that air box lid on or off? And what's your elevation?
@alexscaggs8406
2 жыл бұрын
@@FullSpeedImpulse currently on and I'm at sea level
@FullSpeedImpulse
2 жыл бұрын
Well taking it off will definitely open it up. But you will definitely have to jet bigger for sure
@JacobEcret
Жыл бұрын
i have an aftermarket fuel screw, but mine seems to back itself off. so annoying.
@FullSpeedImpulse
Жыл бұрын
Do you have it turned maybe a little to far to get the bike to run right? And are you sure the spring is still on it?
@JacobEcret
Жыл бұрын
@@FullSpeedImpulse nope, 2 turns. I have checked and checked. And checked again. I bought a new screw I think the spring is gone, wore out, or broke
@JacobEcret
Жыл бұрын
@@FullSpeedImpulse so I took the carb off, and some idiot thought it was a good idea to use a fuel screw without a spring. Bought it with an aftermarket screw
@FullSpeedImpulse
Жыл бұрын
Well that’s a easy fix at least! Lol
@JacobEcret
Жыл бұрын
@@FullSpeedImpulse haha yeah, I sacrificed a pen and cut the spring to a feasible length. Seems to be a lot tighter now
@edwardrodriguez8846
9 ай бұрын
i have a 2012 yfz450 on stock jets it pops on deceleration
@FullSpeedImpulse
9 ай бұрын
Anything aftermarket done to it?
@edwardrodriguez8846
8 ай бұрын
@@FullSpeedImpulseall stock but i just put on a evo r slip on
@FullSpeedImpulse
8 ай бұрын
@@edwardrodriguez8846 ooo yea. Time to put some bigger jets in her. You could try a mild bump up in jetting 42-45 pilot and a 172-175 main. If your not against it, good time to remove that airbox lid since your rejecting anyways. You’ll make a noticeable difference in power if you do.
@Drum3rboy14
2 жыл бұрын
lol the carb is just leaking hard.... just throwing away 110 like its water
@FullSpeedImpulse
Жыл бұрын
Running 116 oxygenated but dang you ain't lying. Also just looks like it's from the bowl drain screw or somethin. Getting ready to get her back out here soon so I'll be checking that out for sure. Lol
@jesussilva791
2 жыл бұрын
My elevation level is 2,835
@carlosvitela901
2 жыл бұрын
Hey, what’s up man! Just watched your video, I was wondering if you could probably give me some info. Don’t know too much about quads! Would appreciate it if you would get back to me, thanks!!
@FullSpeedImpulse
2 жыл бұрын
Hey! I can try my best. What do you have going on?
@carlosvitela901
2 жыл бұрын
@@FullSpeedImpulsei think it’s the carb! I bought It and the choke screw is messed up, I’ve seen another yfz carbs and it does not look like mine!
@FullSpeedImpulse
2 жыл бұрын
First when you say the choke screw do you mean the idle screw(its a knob) or the air/fuel mixture screw? Can you see if it say keihen on the side of the carb? Any motor work done?
@carlosvitela901
2 жыл бұрын
@@FullSpeedImpulse would you happen to have a email or so…? Would email you some pics! The quad is currently in my hometown I bought it there, I’m currently in the states!
@6.2pushinP
3 ай бұрын
Hey man i was riding and my bike died now it’s doing doing idle and shuts off im running GyT-R pipe k&N and at 4,000 elevation im Arizona get back to me for let’s thanks !!!
@FullSpeedImpulse
3 ай бұрын
Man I don’t know. If you haven’t changed anything on the bike and now it isn’t running right. Your prolly past jetting. What is your bike doing now?
@6.2pushinP
3 ай бұрын
@@FullSpeedImpulse it’s turning and will turn on and idle and shut up and then it will just turn but won’t turn on and it killed my battery so im clean the carb and stuff but i just got the bike it’s a 2004
@FullSpeedImpulse
3 ай бұрын
@6.2pushinP okay. Know anything about the bikes history? Last time rebuilt?
@6.2pushinP
3 ай бұрын
@@FullSpeedImpulse i do not said he is second owner didn’t say anything got rebuilt bike was riding good for the weekend the just bogged out in the middle of the ride then turned back on few minutes after rode off and then turned off
@FullSpeedImpulse
3 ай бұрын
@6.2pushinP we’ll go through the easy steps. Like you said clean the carb. And check for a good spark too. Hopefully it’s something simple. Let me know what you come up with!!!
@Rylenstacy
Жыл бұрын
What a arms r those?
@FullSpeedImpulse
Жыл бұрын
Zbroz a arms. They are pretty nice.
@FullSpeedImpulse
Жыл бұрын
I believe they are not insanely expensive either
@Rylenstacy
Жыл бұрын
@@FullSpeedImpulse I’m looking at full fights for the price
@FullSpeedImpulse
Жыл бұрын
@@Rylenstacy I’ve actually owned those before too
@FullSpeedImpulse
Жыл бұрын
They are okay. Are you doing long travel?
@betquick
2 жыл бұрын
Its Leaking something there
@FullSpeedImpulse
2 жыл бұрын
Not from that. But one of our projects we've had in there for sure.
@betquick
2 жыл бұрын
@@FullSpeedImpulse you can see it dripping from the carb
@FullSpeedImpulse
2 жыл бұрын
Hmmm idk. I'll have to take a look at that then. I thought you were talking about the spot on the ground. Could be a dried up seal on the carb. Does not get ran enough that's for sure.
@jonpedulla4802
8 ай бұрын
25 degrese isnt cold
@FullSpeedImpulse
8 ай бұрын
Well for around here it’s below the average riding temp, making it cold for the quad.
@Peedarb
2 жыл бұрын
Bro you have way too big at jets in there
@FullSpeedImpulse
2 жыл бұрын
You run bigger jets with oxygenated race fuel. Also e85. I had smaller jets in it and it was popping idling super high shooting flames out and wouldn't even rev all the way out. With the fatter jets she's way happier. Just have to sweeten up the bottom end a little.
@FullSpeedImpulse
2 жыл бұрын
The issue is I rarely ride the quad so don't have a lot of dial in time with her. I built her from just a frame about 5 years ago now. There's a long story behind all this but long story short I won't ever sell it. Lol
Пікірлер: 230