Had a 24t with a Wisconsin 2cylender motor. Best memories I have with my dad was haying.
@jimcox6687
2 жыл бұрын
You are correct about the chain on the clutch getting stretched. It Throws everything out of time
@BALERMAN
2 жыл бұрын
You need anything for parts call 607-846-5959 nice to meet you Jim Cox 😊
@thompsonfamilyhuntingadven4036
3 жыл бұрын
Just done a bit of a restoration on Dads 24T and got it running for the 1st time in 14yrs. Had AWFUL trouble getting timing correct despite having the original owners manual. Found another scrap/parts value baler and noticed lots of wear in our knitter teeth in comparison, swapped out and fixed timing issues mostly next were tucker fingers were twisted and over extending.... anyhow long story FINALLY got it sorted and running and baled over 450 bales. Question is, parts. Here in Australia parts are about as rare as hens teeth, were can we find parts in the future short of cannibalising the limited parts left on the scrap value baler.
@paulspeigle6334
3 жыл бұрын
Shawn, I know this is an old post, but the baler parts link goes to some other type of balers.
@mikenicholson2548
10 жыл бұрын
Good video one thing to add check the plunger bearings if the plunger moves side to side you will be shearing fly wheel pins like crazy.
@kathydickethier6845
3 жыл бұрын
Hi Shawn - Liking the videos but can't seem to find website; keep getting redirected. Would really like to see how to replace wear pads. Trying to remove old fixes that aren't working and get the proper parts. THX, KE in Maine
@BALERMAN
2 жыл бұрын
607-846-5959 for your parts and information needs 😊
@danielavilleda9648
6 жыл бұрын
hello Shawn I need to know if you can give information about the same square baler. my father has the same machine but he is having problems with the needles, they are broken all the time. he don't know what is the cause of this problem. or how to prevent this problem. I hope you can help me.
@robertcreaney2136
7 жыл бұрын
Thanks for the video. great information
@jarrinwoodruff1863
2 жыл бұрын
Could you just paint the slide bridge pads yellow to find them as well?
@GoaliebossTV
11 жыл бұрын
Awesome video! I was looking on your website, just wondering how many teeth you get when you buy that pack for $19.50? Also, are those any good for straw?
@rgwierdly
8 жыл бұрын
roxanne miller, is there not a picture instruction on the underside of your twine lid?
@paulhewson5414
11 жыл бұрын
Great vid! I need a billhook for my 14T... Any reccomendations?
@BALERMAN
2 жыл бұрын
607-846-5959 we have aftermarket
@roxannemiller6512
10 жыл бұрын
DO you have a video on how to put in Twine on the 24T. We are baling hay for the first time and have no idea how to install the twine correctly.
@canpoling
10 жыл бұрын
Did you find this info? We have the manual and it still isn't making sense.
@canpoling
8 жыл бұрын
Thank you!
@davejohnson2937
2 жыл бұрын
hi seen your vids do you have site to buy parts for the green balers?
@BALERMAN
2 жыл бұрын
Call 607-846-5959 for parts
@davejohnson2937
Жыл бұрын
@@BALERMAN called the number left a message never got a call back..
@BALERMAN
Жыл бұрын
@@davejohnson2937 bare with us we are only two people and 60 calls a day makes it rough
@2008greiner
9 жыл бұрын
Trying to get big gear off in gearbox to replace. Little bearing and the big seal
@donnieadams9552
2 жыл бұрын
I need the rear bridge pad do you have it
@BALERMAN
2 жыл бұрын
Call 607-846-5959 or text the same number
@irock155
6 жыл бұрын
you're that ninja...
@noelchitwood5250
10 жыл бұрын
How do you time a JD baler. I have a 216 and have been running it for years but have never had to time it. noel
@BALERMAN
8 жыл бұрын
Call 607-846-5959
@samp2148
8 жыл бұрын
привет памаги выставить зажигание на прессподборщике джон дир 224т видео выкень а тоя крутил тяги предохранительный клапон паршня пакажи как их выстовить все тяги размеры в сех тяг и как правильно выставить книги нет за всё бальшое спасибо толька все на русскам языке пажалуста
@scottmorris1747
9 жыл бұрын
Need to time my jd bale
@danielavilleda9648
6 жыл бұрын
hello Shawn I need to know if you can give information about the same square baler. my father has the same machine but he is having problems with the needles, they are broken all the time. he don't know what is the cause of this problem. or how to prevent this problem. I hope you can help me.
@BALERMAN
2 жыл бұрын
Sure Call 607-846-5959
@danielavilleda9648
6 жыл бұрын
hello Shawn I need to know if you can give information about the same square baler. my father has the same machine but he is having problems with the needles, they are broken all the time. he don't know what is the cause of this problem. or how to prevent this problem. I hope you can help me.
Пікірлер: 35