I just recently (June 14/24) took the carb off my 9.9 and to get at that one nut on the carb easier, I took the pull cord assembly off which took no time at all... easy peezy. Just make sure you u zip tie it together so that it doesn't spring apart. When putting that nut back on the carb, grab it by the handle and set it down on the ground or work bench.... this way you have a better chance of the nut sitting flat on the threads.... easy peezy!
@josephmessina4020
12 күн бұрын
I did the same but I put a nut on the pull cord bolt
@dadams19111
4 жыл бұрын
Great video, starter, one bolt and everything is accessible. Nice video!!
@jdblack9703
4 жыл бұрын
Great video! I think I would take the starter off first. That would make the access easier but watching you solve the problems is worth the price of admission. Thank you for sharing your techniques.
@kenwolf1056
3 жыл бұрын
Have enjoyed all the videos! God bless
@Michaelsbackyardmarina
3 жыл бұрын
Glad you like them!
@ericthibaudeau1265
3 жыл бұрын
Thank you Sir! Thanks for taking the time to put up this video. :)
@Michaelsbackyardmarina
3 жыл бұрын
Glad it was helpful!
@larrymilsap5123
2 жыл бұрын
Great video! I was able to get my outboard running tiptop in about 30 seconds!
@Michaelsbackyardmarina
2 жыл бұрын
Excellent!
@aronharper7001
4 жыл бұрын
Storm came in and sunk buddies boat and this motor but we found er and took it apart to clean it up forgot how to put it back together haha! This video will get him back on the high sea's in no time! Thanks
@jessecrews
10 ай бұрын
Avoid the headache, grab a 9/16 open end wrench and a long zip tie (or anything to hold the pull rope starter together), and remove that top starter bolt and set starter to the side and it makes it a world of difference.
@b27rampage
Жыл бұрын
.30 SECOND MARK BIG SPIDER GOING UP UNDER THE SHELF
@scottczarnecki2936
2 жыл бұрын
That shirt is 🔥🔥🔥
@Michaelsbackyardmarina
2 жыл бұрын
Thank you very much, thanks for watching
@shawnsurman9562
4 жыл бұрын
I had luck with temporarily removing the recoil starter to get to the flat head screw and the other carb nut. I just held a recoil in my hand to keep it from flying apart and put it back on until I was done with carb rebuild.
@Michaelsbackyardmarina
4 жыл бұрын
Yes definitely don't let the spring go. Not the end of the world if it does. I'm working on one now that I have a spring on order for.
@francimasaza8749
4 жыл бұрын
give up screw on the starter, not to explode
@stevec4209
4 жыл бұрын
I just use some electical tape to hold recoil assembly together and then just hang it over the side
@lifeistooshort649
4 жыл бұрын
My fuel line is also held on with zip tie.
@Michaelsbackyardmarina
4 жыл бұрын
I'm learning zip tie is an ok way to go.
@gunfisher4661
2 жыл бұрын
Sure would be nice to get a hold of a service manual for some of these motors.
@Michaelsbackyardmarina
2 жыл бұрын
they have them available on marineengine.com
@dannilaser16
2 жыл бұрын
I removed the pull-start, which made it a lot easier to remove the carburetor retaining nut.
@thomasjoseph5876
2 жыл бұрын
That's what I just did too. My motor got submerged in a storm last night. I hate having to go thru my motors every time one gets swamped in the lake because the only thing that comes to us out of Fargo, ND is 80 mph winds lol. Now I remember why I hate renting out my small Lund Boats with Evinrude motors lol. I had to laugh when he said his fuel line was held on by a zip tie and he didn't think that was stock. Guess again lol.
@dannilaser16
2 жыл бұрын
@@thomasjoseph5876 my fuel line is held on by a zip tie too. Lol.
@joshmatthew4125
3 жыл бұрын
As soon as I saw that shirt I through my dad made a KZitem video.
@PaidPrices
11 ай бұрын
My fuel line has a zip tie too, I wondered if it was factory.
@henrycole8705
4 жыл бұрын
These motors suffer from primary vacuum loss often. because the crankshaft seals dry out and leak. Causing rough idle
@gunfisher4661
2 жыл бұрын
Good tip ,forgot about that and I just learned it on T-mikes channel the other day.
@ud4458
2 жыл бұрын
great video. Thank you. Any idea why Johnson 9.9 outboard would blow oily chunks with some fuel when starting ?
@Michaelsbackyardmarina
2 жыл бұрын
What's your mixture and what kind of two stroke oil you using?
@ud4458
2 жыл бұрын
@@Michaelsbackyardmarina Sorry I didn't see the notification for your comment. I am using West Marine TC-W3. I think where I went wrong is that I was using the old gas can and I just added the oil to the can without making sure it was shaken. After getting a new fuel tank, the chunks are gone, but now it wont stay running without having to keep playing with the choke. Also the plugs were fouled. I just got my carb kit in the mail! Time for a rebuild. With your video should be no prob! Thank you RMD
@danieldoyon2381
3 жыл бұрын
I need a 15 hp carb for my 9.9 1986 :)
@Michaelsbackyardmarina
3 жыл бұрын
hard to come by. good luck
@jimmythompson9394
2 жыл бұрын
What was the float drop?
@alexandreplouffe587
10 ай бұрын
Hi I got a 1989 evinrude 9.9 and the knob where the stop button is stuck it doesn't what to turn is there a function to that knob I'm thinking yes I saw u use it if yes what does it do on and how can I get it to turn thanks !
@richardrobbins-wg4nq
11 ай бұрын
Pull the starter, that small screw and right side nut is then easily accessible
@richardrobbins-wg4nq
11 ай бұрын
Be sure to hold the starter together so the spring does not unwind . Leave bolt in and wrap with tape to hold everything together
@Michaelsbackyardmarina
11 ай бұрын
for sure, thanks for watching
@ronbarbee4553
4 жыл бұрын
If the transmission lever is in forward, can it be hand cranked? I have a 1978 model. I can't seem to move it to neutral with the engine off. I'm relatively new to these old 2-stroke engines.
@Michaelsbackyardmarina
4 жыл бұрын
they are designed so you can't start them in gear for safety reasons on newer models like in the 80s. Not sure about a 78. Mostly they have a throttle lock out to minimize the ability to rev the engine without it being in gear.
@floridasaltlife
4 жыл бұрын
Roll the throttle back to idle first !!
@broutdoors8248
4 жыл бұрын
I have a 1989 9.9 and I am able to start it when it is in forward
@ralphbarker7791
3 жыл бұрын
You will have to show a segment on installing piston rings next. I don't think that you have showed this yet?
@CoryRoy
2 күн бұрын
what was that little red seal for? I didn't see you install it?
@SadiNergizdal
Жыл бұрын
Hi, your explanations are excellent. Where can I find a 1998 Johnson 9.9 carburetor kit?
@Michaelsbackyardmarina
Жыл бұрын
marineengine.com
@Vhiadra
3 жыл бұрын
I have a question, I have the same motor I never had it running yet but it seems that when it's in gear if I turn the throttle backwards it kicks itself into neutral, is that normal?
@Michaelsbackyardmarina
3 жыл бұрын
Haven't run into that before.
@Vhiadra
3 жыл бұрын
Woah I'm so stupid, I went and double checked yesterday and it turns out it wasn't fully clicked into gear Hahaha I'm sorry for wasting your time!
@scottcooper3161
3 жыл бұрын
1/3 cup = 2.67 oz that is what I use . Ams oil is the best .
@Michaelsbackyardmarina
3 жыл бұрын
Good stuff
@crynod
6 ай бұрын
What year model is this outboard?
@willwenis4728
3 жыл бұрын
RMD Creations I have a 1986 Johnson 15 hp and when it starts it will idle super high and then go low and then high again and sometimes when I start it it will start to idle super high and then I can’t turn it off even when I disconnect fuel and choke it. Do you have a solution to make it idle smoother?
@Michaelsbackyardmarina
3 жыл бұрын
sounds like you have some excess fuel and air getting in when it shouldn't
@Bobbybbops
3 ай бұрын
Where does that red piece go???
@maxhunts_
3 жыл бұрын
Question been running mine in a drum now I’m getting a lot of oil coming out on the sides of the drum and I running to much oil in the fule, running at 50-1
@Michaelsbackyardmarina
3 жыл бұрын
That's just the nature of the two stroke. To help break down the oil you can put a dish washer tab in the water. That's what I do on my big tank
@gunfisher4661
2 жыл бұрын
Better check the lower unit to be safe had it happen once.
@chrisgray3147
3 жыл бұрын
How easy is it to line up and re-install the flywheel ?
@Michaelsbackyardmarina
3 жыл бұрын
It's keyed so it's easy peasy
@Scott.Farkus
4 жыл бұрын
There's 32 oz in a quart now
@thomashuskey3531
3 жыл бұрын
Hey , that's what I was fixing to say !!! I know a quart of beer says 32 oz. Lol !
@joemartin6439
2 жыл бұрын
Will a Johnson 84 9.9hp turn into a 15 with a 15hp carburetor swap for 9.9 carburetor
@Michaelsbackyardmarina
2 жыл бұрын
Check out leroysramblings.com and find out.
@gunfisher4661
2 жыл бұрын
some models you have to swap the exhaust tube also.
@franckboisson1496
2 жыл бұрын
Quand on a pas la clé de 7/16 c'est pas plus simple de dèmonter le lanceur?
@Michaelsbackyardmarina
2 жыл бұрын
Thanks for watching.
@hammer9856
3 жыл бұрын
I absolutely hate it when a bug crawls up one of my orifices... LOL
@dennisgraykowski348
2 жыл бұрын
What kit did u use… could u provide me a link?
@Michaelsbackyardmarina
2 жыл бұрын
Look it up on marineengine.com
@danieldoyon2381
3 жыл бұрын
what is the red part ???
@Michaelsbackyardmarina
3 жыл бұрын
I think you are talking about the part that won't let you start the motor in gear or open throttle.
@danieldoyon2381
3 жыл бұрын
@@Michaelsbackyardmarina i talk about thé part juste braisé thé crank
@tommyjackson6216
3 жыл бұрын
Mike I lost my low end needle setting where is a good place to start ??? 9.9
@Michaelsbackyardmarina
3 жыл бұрын
1 1/2 turns from bottomed out
@diegodosreisflorenco6953
Жыл бұрын
hello where to find johnson 16 hp four stroke 4 stroke engine gas pump
@Michaelsbackyardmarina
Жыл бұрын
marineengine.com
@cienciaytecnologia7255
4 жыл бұрын
how many turns do you have to give the needle
@Michaelsbackyardmarina
4 жыл бұрын
1 1/2 turns
@marcus123841
3 жыл бұрын
I’ve only ever seen the fuel pump on the other side of the motor ???
@Michaelsbackyardmarina
3 жыл бұрын
interesting.
@joemartin6439
2 жыл бұрын
You have to remove the starter and a right nut come off easy it is a bitch to find the nut later down the shift lick hole
@Michaelsbackyardmarina
2 жыл бұрын
yes it is. Welcome aboard
@joemartin6439
2 жыл бұрын
Sta Bit I s no good dear friend just take off the starter dude
@Michaelsbackyardmarina
2 жыл бұрын
indeed. that's what I do
@user-mc9ny2iz7k
3 жыл бұрын
Кто мне такой подарит?
@Michaelsbackyardmarina
3 жыл бұрын
Who will give me such? Not sure I understand the question
Пікірлер: 92