You should show how you apply the heat that what could make the sense of the video
@user-li4ik9qs8c
6 ай бұрын
I was watching the vid jst 4 how he’ll apply heat to the the capl.
@IsheImagessa
6 ай бұрын
thanks a lot man I wanted to actually see you weld, because that is the part beginners can get help from
@josephmutambirwa8469
3 ай бұрын
We really wanted to see how you welded, you removed the best part of the video 😢😢😢
@HDXFH
Жыл бұрын
Very tricky to solder aluminium, been successful though
@gilliesservices317
2 жыл бұрын
firstly Thank you for your videos i learn a lot from it.I have also struggled with this.I use that mix combound called steenvas and that also works fine.It just needs drying time but i honestly joint a lot of them with steenvas and never had a come back on any of them.I tried welding them but personally its a nightmare.😀
@josh42741
9 ай бұрын
Thanks for sharing. I thought I would have to buy a Lokring kit.
@pineprod9037
3 ай бұрын
You must
@phoenixduncunn9777
3 жыл бұрын
Great job, keep the videos coming please 👍
@wsrepairs7080
3 жыл бұрын
Can you please make another video showing the welding procedure, I weld 3/16 on the drier capillary side (+- 30mm) and then Epoxy steel the capillary and pinch the end of the copper, I leave about 10mm of the capillary with no glue, as to not create a blockage. So I put the Epoxy on the capillary, with 10mm open on the tip, then slide in the tube and pinch the 3/16" at the very tip where the capillary enter. Leave the repair over night and charge the system the next day. It worked 100%, but will it last over time? Any thoughts? By the way, I like your videos, very educational. Please do make more.
@JDNelRefrigeration
3 жыл бұрын
Epoxy was used in the 1950s by Kelvinator USA to join it exactly the same way you do and it worked. Nothing wrong with it but I prefer welding it on.
@mansoorbaloch5686
2 жыл бұрын
What is the mean of ur video if we can't se the dryer to silver cappilary weldind
@JDNelRefrigeration
2 жыл бұрын
I was alone when I videoed this I will remake another
@HerholdGelant
14 күн бұрын
Hi got a leak on the incoming of the aluminum pipe in lower deep freezing
@JDNelRefrigeration
12 күн бұрын
If you can reach that section, then it is easy to repair.
@kojsiusoaliu6772
3 жыл бұрын
I loop the capillary around the dryer and use a little cheap clamp then no more tension
@JDNelRefrigeration
3 жыл бұрын
Very good idea
@johndejohn2136
4 ай бұрын
Show us how you did it not only explanation, poor vi
@raphaelmoloi807
2 жыл бұрын
I want to see u doing a welding setion
@shahidabbas5830
10 ай бұрын
The main part was missing,make another video,let someone else hold the camera
@nitinsawant5453
2 жыл бұрын
how.you.brezed.the.capillary.you.didn't.show.us.
@davejohnsonnola7908
3 жыл бұрын
Don't believe I've seen aluminum cap tube before on this side of the pond.
@JDNelRefrigeration
3 жыл бұрын
The only fridges Ive seen with aluminium capilary tubes are from Brazil and South Africa.
@ljslw
Жыл бұрын
I’ve never seen it in the US. I’ve replaced an repaired aluminum evaporators before. They don’t need much heat at all.
@amierodienbray1702
Жыл бұрын
Those fridges come from Lesotho. It a nightmare to weld those. I have a job where the coil is split on an upright single door commercial freezer and has two capillaries. These two capillaries is fitted into a 5/16 pipe and from the 5/16 it is reduced to 1/4 and this goes into a 1/4" by 1/4" pencil drier. Also the suction return is 5/16" and a pin hole developed on the pipe and it is not on the weld but on the pipe itself. It looks like rusted due to the armaflex being wet.
@MikeInga
2 жыл бұрын
Useless video, what tool you used to weld and how you apply heat is what is important.
@editormeda6250
3 жыл бұрын
I think you should have shown us the actual wellding process,,,, but anywhere thanks sir....
@JDNelRefrigeration
3 жыл бұрын
I was alone when I recorded this, I used an Oxyacetylene with a very small flame.
@Braundesh
3 жыл бұрын
How small was the flame that's the question
@JDNelRefrigeration
3 жыл бұрын
@@Braundesh Very small! The smallest that I could get my Oxyacetylene to burn at.
@Braundesh
3 жыл бұрын
@@JDNelRefrigeration thank u
@maxkambendera2399
11 ай бұрын
Why you don't show how you did it
@ebrahimparak1133
2 жыл бұрын
What's the point of the video is you dont demonstrate how to attach the capillary
@coolboymbwe
Жыл бұрын
Where can i find the rod im in Botswana
@slowmotion6839
3 жыл бұрын
What is the name /specs of this rod ?
@JDNelRefrigeration
3 жыл бұрын
Aluminium F/C rods. I get them from Probraze Metals
@markrobby7136
2 жыл бұрын
In my case there is gas coming from the pipe and won't allowed me to weld it. Any solution please?
@JDNelRefrigeration
2 жыл бұрын
You need to open the system somewhere else. Preferably on the suction side.
@markrobby7136
2 жыл бұрын
@@JDNelRefrigeration , thanks, but I don't get it, what system?..it's just like yours the area where it's cut apart.
@rafaelbrunisilva4826
2 жыл бұрын
whats the brand of refrigerator?
@johannnel3888
2 жыл бұрын
It was a Defy
@lyndonlakhansingh
3 жыл бұрын
What type of torch did you use to weld ?
@nozinikane6376
4 ай бұрын
And he is not answering to questions
@tsepangmotiki722
4 жыл бұрын
Where can l find those rods in free state?
@JDNelRefrigeration
4 жыл бұрын
I get mine from Probraze. They may courier them to you if you ask.
@tsepangmotiki722
4 жыл бұрын
@@JDNelRefrigeration thanks
@boitumeloromeo3488
4 жыл бұрын
Where can i buy the Rod?
@JDNelRefrigeration
4 жыл бұрын
We get them from Probrase
@boitumeloromeo3488
4 жыл бұрын
No other option to fix ,if capillerynits broken?
@JDNelRefrigeration
4 жыл бұрын
@@boitumeloromeo3488 Either you have to weld it or replace it with a copper capillary.
@waleskambwiri822
4 жыл бұрын
Useless...😢😢😢
@basilmontaque3515
Жыл бұрын
This dont make any sense
@Jeff-qz8sb
3 жыл бұрын
You are not a good teacher. Why did you jump the brazing part?
@JDNelRefrigeration
3 жыл бұрын
Because I was videoing myself doing it.
@user-li4ik9qs8c
2 жыл бұрын
@@JDNelRefrigeration You skipped the part that every body was watching this vedio for!
Пікірлер: 59