I have one of these in a mobile application - nothing short of fantastic. And at a fraction of the cost of its competitors!
@junctek1802
Жыл бұрын
Thank you!
@cesaranzalone4797
Жыл бұрын
I have one too, under testing. I can see that is accurate and intuitive. The bluetooth connection is a nice plus, and the application is cool, but with some room for improvement.
@junctek1802
Жыл бұрын
Thanks for your suggestion
@PurpleMrMojo
5 ай бұрын
All of the wiring diagrams show a relay between the battery and the load with a wire connecting to the meter computer able to turn on and off the relay but what is that all about because nothing I find in all of the KZitem videos show anything about that relay. Is that just a turn off, all 12 V power remotely if needed?
@electronistul
7 ай бұрын
Hello, can you confirm that the coulombmeter function does what I think it does, namely: During the life of a battery 1-10 years (whatever it is) it charges and discharges, the coulombmeter function measures what current comes out and what current comes in (subtracts and adds - averages, etc.) then results (normally after several cycles, not instantly) the capacity in Ah of the battery. Let's say we have a 100Ah battery and I cycle it 20-80%, the coulomb meter should show me after some time a capacity of 60Ah (ideal). If we reduce the losses, I think somewhere around 55-59Ah. This is true ? Does it do what I think?
I'm using KH140F. When I run Bluetooth app, it works fine but ALWAYS freezes after a certain amount of time. The same goes for turning off the data record. Is there a solution?
@diydsolar
10 ай бұрын
Hi, I have a doubt The 100a version is really a 200a shunt. I understand that you do that to be "confortable at high limit of current" But if I use it normal a low values and sometimes during short times at 125 or 150A.... Does it measure them? Or is it software limited at 100A? I know that there is a 400A version, but I understand that under 3A or even under 1A the accuracy of 100a version will be much better than the 400a version. Hope your answer, thanks.
@junctek1802
10 ай бұрын
The KH110F will not be damaged by a brief current of 150A.
@diydsolar
10 ай бұрын
@@junctek1802 will it measure it? Or it will show 100.0 A as a limit ? Thanks
@junctek1802
10 ай бұрын
@@diydsolar The maximum display can be up to 120A
@ericklein5097
Жыл бұрын
Do you have some kind of chart that compares the differences in your models? I was looking at the KG but I see this KH model is fairly new. Is the only difference the addition of low temperature protection relay triggering? (I am aware that you have to buy your own relay)
@junctek1802
Жыл бұрын
www.aliexpress.com/item/1005005293126063.html?spm=5261.ProductManageOnline.0.0.1c522ddbpX5Xdf You can click on this link, there is a comparison table between KG and KL
@si12volt1
Жыл бұрын
my battery is 12V 190Ah LiFePO4 Lithium Battery 2432Wh 150 BMS and a 60A MPPT Solar Charge Controller with one Should I get of the 3 choices will the 100a version be enough?
@junctek1802
Жыл бұрын
If your working current does not exceed 100A, you can purchase KH
@user-zo3dc8go2h
Жыл бұрын
Hi, what is the diameter of the bolts on the 400A shunt?
@junctek1802
Жыл бұрын
Dear 10mm
@lepadatupetrica8487
Жыл бұрын
There is any way to I integrate this on Home assistant? Thank you
Пікірлер: 20