still interesting to learn about the air intake. this can be very helpful. make a hole to the filter and close the original tunnel
@tuningandmodingcarcroatia4080
3 жыл бұрын
Yes good work. Waiting for part 3. I have plan to make buggy powered by that engine so thanks a lot for sharing that knowledge.
@baldodsgarage4795
3 жыл бұрын
Part 3 should be out in spring - it would be a shame to drive this engine on salty roads :)
@vresak1619
10 ай бұрын
Hi Excellent job What exactly machine shop did to increase oil flow at the rear bearing? I like to do same. Thank you in advance
@speedphreax
3 жыл бұрын
Great video! What does the modification of the rear main bearing look like? What is the difference compared to the standard one? I am not too familiar with these engines so sorry if it is a dumb question.
@baldodsgarage4795
3 жыл бұрын
Thanks! Experienced machine shop worker (he did a LOT of these engines) told me to use his old stock very soft-coper compound bearing instead going oem wich is bit harder. This mod is good for engines wich revs higher than usual. Bearing will wear faster but scoring will less likely appear :)
@Sobieski_IV_Emperor_Gods_mercy
Жыл бұрын
,,Friends, in 30min geht es weiter." -Also bis halb 4. ☝🙂
@erkdrey
3 жыл бұрын
Good work, well done
@adamorowski9039
3 жыл бұрын
A gumki na rurki popychaczy to kto założy?
@baldodsgarage4795
3 жыл бұрын
To tylko przymiarka - trzeba było się upewnić czy zawory w tłoki nie wjadą ;)
@anon-mh8mp
3 жыл бұрын
Głowica 2 mm, wałeczek jaki? Poza tym reszta standard czyli dziury w puszcze filtra inne dysze w gazniku itp?
@baldodsgarage4795
3 жыл бұрын
Wałek FT.20020. Załatwiam szczelinową rurkę emulsyjną ale ciężki temat - pierwszą partie mi źle wykonali.
@ludwiks971
2 жыл бұрын
Czy nie zapomniałeś uszczelki pod tylną panewkę główną? Bo ja właśnie składam silnik i po przykręceniu wszystkiego zdałem sobie sprawę że nie mam tej uszczelki xD. W dodatku, czy na twojej panewce tylnej była taka cieńka okrągła uszczelka?
@berre1994
2 жыл бұрын
Hello, I have some questions about some of the things you did. Did you use 10 of the standard red seals for the camshaft tubes? I've skimmed my head 1,5mm and i'm afraid they will be to large now. Also, the holes you drilled before the air filter, does this make any difference to performance? Overall, a very nice and detailed video. Regards, Bert
@baldodsgarage4795
2 жыл бұрын
Hello, I used standard red seals. You can buy adjustable pushrod covers allegrolokalnie.pl/oferta/regulowane-oslony-popychaczy-126p if You worry about leaks but factory ones work well up to 2mm. Holes in intake allow engine fan to force some air to engine. It is very popular mod. I would gues it adds about 1hp if done corectly (carb dont like to much holes) . Regards, Bartosz
@berre1994
2 жыл бұрын
@@baldodsgarage4795 thanks for the reply. I will try the standard ones then, hopefully it works. For now I will stay away from the air intake mod. First let's see if everything works before making new modifications. "Supercharging" does sounds tempting and with this car, every horsepower makes a difference.
@berre1994
Жыл бұрын
@@baldodsgarage4795 Hi Bartosz, Just took the engine out again for some winter maintenance. I'm willing to try the air intake mod now. Do you have a link with some information on how to do it? (What size of holes to use, the amount? Should I block the existing intake or can I leave it? Or cut the existing intake completely off?...) Do you know if I need to re-tune the carb afterwards? Best regards, Bert
@baldodsgarage4795
Жыл бұрын
@@berre1994 Hi, Slight adjustment to carb will help but if You are on "rich" side of AFR You should gateway with it. forum.rezerwa126p.pl/printview.php?t=10363&start=0&sid=752de731d32aa38246b6c81101efbb10 Best regards
@سهيلهاحمد-ش5ي
3 жыл бұрын
رايع جدا
@TheDarkeLTU
2 жыл бұрын
where is the part 3? did it started?
@baldodsgarage4795
2 жыл бұрын
have to edit it :)
@PM-nz9lf
3 жыл бұрын
Good man! What part of Poland are U?
@baldodsgarage4795
3 жыл бұрын
Poznań
@LukAzMA
Жыл бұрын
Gdzie ta 3 czesc? Juz czekam 2 lata 😂
@Cichymoto
2 жыл бұрын
Panewkę główna tylną kupowałeś nową?
@baldodsgarage4795
2 жыл бұрын
Szlifierz miał zapas panewek do malucha trochę bardziej miękkich od ori (tam jest małe ciśnienie oleju) i w moją oprawę ją wstawił.
@Llampalleq
2 жыл бұрын
What happened with parts 3 and 4?? 😄🤨🙄
@baldodsgarage4795
2 жыл бұрын
It is recorded but i dont have time to edit it :/
@gordonbeattie9316
11 ай бұрын
Hi,could someone tell me what the torque settings are on the head and rocker,I have a 650 engine, Thanks.
@Rob-Sam
3 жыл бұрын
Cześć. Jak już pisałem pod ostatnim filmem. Czy sprawdzałeś może na hamowni ile ten Maluszek ma koni po tej modyfikacji?
@baldodsgarage4795
3 жыл бұрын
Cześć, silnik jeszcze nie w maluchu ale latem planuje sprawdzić na hamowni :)
@Rob-Sam
3 жыл бұрын
@@baldodsgarage4795 Super. Czekamy zatem na wyniki.
@Jacyk
3 жыл бұрын
Widzę że jesteś Polakiem :D Bardzo przyjemnie się to ogląda, przeprowadzone modyfikacje są moim zdaniem słuszne, sam chce zrobić coś podobnego ;) złożyłeś do końca ten silnik? Masz filmik jak to gada? :D Pozdrawiam
@baldodsgarage4795
3 жыл бұрын
Silnik złożony, czekam aż sól zniknie z dróg. Będzie Filmik pokazujący jak to gada :) Pozdrawiam
@abridgingpanda7372
3 жыл бұрын
How to change the oil filter?
@baldodsgarage4795
3 жыл бұрын
There is no flow-thru oil filtrer so You dont change it. Oil is filtered in pulley by centrifugal force and all You need to do is clean it :)
@fiat500lover2
3 жыл бұрын
Hello, I have found your video very helpful in reference to rebuilding the engine. Is there anyway I can reach you via email? Thank you in advance
@baldodsgarage4795
3 жыл бұрын
Hi, if U have any questions: kant.kwadrat@gmail.com
@maciejbielawski6220
3 жыл бұрын
Dałeś uszczelkę pod tylną główna panewkę?
@baldodsgarage4795
3 жыл бұрын
Tak jest :) Tył był skręcany na gotowo z kołem zamachowym.
@salvatorepappalardo2496
3 жыл бұрын
Montaggio non correttamente. Passaggi completamente sbagliati, il castelletto, ecc
@tarnowek1
3 жыл бұрын
Swietne video . Od dzis jest masz suba .Kupilem sobie malucha z 1989 i mieszkam w Australi tutaj tu jest ich bardzo malo..malo tez jest wiedzy o nich mam prosbe gdyz chcialbym go zaczac uzywac lecz problem w tym ze jak go odpale to strasznie czuc spaliny w kabinie ale tez do okola samochody, nie widac jakos specialnie dymu z rury wydechowej ale strasznie smierdzi..help :)
@baldodsgarage4795
3 жыл бұрын
Cześć, najprawdopodobniej uszczelka pod głowicą poszła i ogrzewanie ciągnie spaliny do kabiny. Sprawdź śruby drążnone wkręcane w głowicę :)
@Grzechu0
2 жыл бұрын
Kiedy następna część?
@baldodsgarage4795
2 жыл бұрын
Jak zmontuję :)
@Grzechu0
Жыл бұрын
@@baldodsgarage4795 montuj szybciej ciekawie się to ogląda :D
@LukAzMA
Жыл бұрын
@@Grzechu0 niech da montaz silnika bez montazu Filmu
Пікірлер: 47