Your video is great, the most detailed I have seen! The trickiest part that most people will get stuck on, is re-assembling the sliding part/metal slide plates/magnets. The easiest and best way that I have found is to leave the magnets for last. Put the metal plates on the little tabs, hold that assembly at an angle so the plates don't fall off and then slide it into the machine where it is supposed to go. After that you can use a small screw driver to pick up a magnet, push it into the hold, and it will lock right onto the metal plate - do the same for the second magnet.
@ZeroDefects7
7 ай бұрын
This was a tremendous help in cleaning my Impressa F9. Almost identical design - the F9 seems to have more wiring. Loved the break for tea! I had a beer instead.
@bobbennett847
9 ай бұрын
This was an excellent video. many people can learn from this. Both the screen angles and the lack of rambling made it excellent. Thank you so much
@jabi2511
Ай бұрын
Thank you very much for an absolutely wonderful video tutorial. I have a Jura D4 and the outlet nozzles in the front of the device are clogged. With your instructions, I managed everything perfectly safely and reliably. The coffee maker works like new! Thank you once again and greetings from the Czech Republic. 👍👌❤🍀🍀🍀🍀🍀
@Art-w2d
5 күн бұрын
Smoothly done - worked for me as well … including the Tee of course, too ! Thank you very much
@ilyafrangos8413
2 ай бұрын
Thank you so much for this video! I was able to take apart my D6 and clean it. Not quite the same and ran into a few obstacles, but was able to overcome them. Your video was incredibly detailed and helpful!
@p.461
10 ай бұрын
Hi. Endlich ein Handwerker der es super zeigt wie man es selber reparieren kann. Top Viedeo. Kaffeeauslauf wieder frei. Daumen hoch. Danke dafür. Werde Dich weiterempfehlen.
@yt.myworks
10 ай бұрын
Danke für das Lob!
@doctornachman
4 ай бұрын
I can't thank you enough for making this video. I saw another one before yours, and it convinced me not to even try. I watched yours, and it broke it down into simple steps i could follow. You gave me the courage to do this myself. The only problem i had was getting the side panels back on properly without gaps. I am now drinking delicious coffee again instead of an expensive repair and shipping bill to Jura. This was awesome!
@yt.myworks
4 ай бұрын
I'm very glad to hear that.
@ilyafrangos8413
2 ай бұрын
I have gaps in the machine I did too and I do not know why!
@borisjulich2947
Жыл бұрын
You are a real inspiration! Thanks for these great videos. Sustainability at is best.
@eagrinstead1
Жыл бұрын
Thank you for demonstrating this process. Your excellent video is going to make this task faster and give me a little added confidence. I know this machine is older but I think it still makes great coffee. Best to you!
@alejandrodvazquez5632
Жыл бұрын
good work friend ... I always watch your videos and learn something new . very careful and professional with what you do. a hug from Daniel Brasil - Rio de Janeiro . Lavazza maintenance technician.
@maikg.2911
Жыл бұрын
It worked, thank you! I have a Jura Impressa C70. The inside and process ist quite similar to the C60. Only few differences.
@DominickCascianoIII
2 ай бұрын
Would not believe the sludge I removed from my unit. About 5 years everyday use. Gross! Haha. Many thanks 🙏
@harryvaniersel4177
9 ай бұрын
Great video, excellent Quality, thanksa lot With the video on my laptop, I managed to reach the nozzles, noticed that the mirror coating of the spout was damaged, a new one is on inquiry. Awaiting delivery, I cleaned all parts and reassembled. The coffee taste has improved!
@yt.myworks
9 ай бұрын
I am pleased!
@Realtor365
Жыл бұрын
Thank you! Mine is having issues w/ the dispensing spout.. rather than coming through just the side dispensers , it’s trickling down the middle..ugh We’ll have to take a look inside. Thanks!
@alejandrodvazquez5632
Жыл бұрын
Guter Arbeitsfreund... Eine Umarmung aus Brasilien - Rio de Janeiro
@DaLetsche
9 ай бұрын
Hat super geklappt. Meine Maschine läuft wieder. Vielen Dank! 😊
@yt.myworks
9 ай бұрын
Das freut mich 👍
@terneuv
Жыл бұрын
Hello , it's coffee time 😉. Merci pour cette vidéo , de France 🙂. 👏👏👏👏👏👏
@PashaWFB
3 ай бұрын
Great video, my C65's flow is like new. Thanks!
@georgschoberl5001
10 ай бұрын
Vielen Dank für dein video hab mich drüber getraut dank dir 😁👍
@brigittedeveld
Жыл бұрын
Thank you for the video, it was a great help!!
@pereant
7 ай бұрын
Meine jura d4 scheint beim cassis rund um den Kaffeeauslauf etwas komplizierter zu sein... bekomme es irgendwie nicht weg nach dem entfernen der 4 torx Schrauben... aber ansonsten war's bis jetzt sehr hilfreich!
@sulejmanovic1
5 ай бұрын
Thank you, this video is amazing.
@grand3000
Жыл бұрын
Danke, hat super funktioniert!
@ReinerHecker-xq6zh
Жыл бұрын
Sehr gutes Video. Meine läuft wieder. Danke
@yt.myworks
Жыл бұрын
Das freut mich 👍
@guicohen
Жыл бұрын
Hi. This was wonderful. Fixed my problem. However, i did something wrong when assembling the machine and now the spout doesn't slide vertically. Probably something with the magnetic things that attach them. Any advice or close up video on how to assemble that part back?
@yt.myworks
Жыл бұрын
Hi, take care in minute 8:55 here the two sheets have to be placed exactly on the pins, these are held from below with the magnets. Everything together must be carefully installed and screwed together so that it does not fall apart again.
@guicohen
Жыл бұрын
@@yt.myworks thanks!!
@JoseGustavoAbreuMurta
4 ай бұрын
Best video! Thank you.
@amertahir
Жыл бұрын
did you add baking soda to the hot water in the container for cleaning?
@MekazaBitrusty
Жыл бұрын
Yes, that was the only thing you didn’t mention. 😂. Thanks for the advice.
@mironi723
Жыл бұрын
Super. Good job
@janoshverdonck9806
Жыл бұрын
Hi, my machine is leaking and i found the spot! Seems like a part is just missing. Could you tell me what is wrong? I don’t know how it’s supposed to be. If you look into frond where the ground container goes, all the way in the back there leaves one water hose to the right, just behind there i have a nozzle with nothing attached. The water just squirts out there. Thanks!
@yt.myworks
Жыл бұрын
Hello, is the same problem as in this video? kzitem.info/news/bejne/mZmunGSciYOBdZw
@MilanOdster
Жыл бұрын
Very helpful, can you show how to replace the pump?
@yt.myworks
Жыл бұрын
I still have to make the video, but the change is very easy. The important thing is that you buy the right pump for your model.
@MatthewNelson104
10 ай бұрын
What is the cleaning product you use to soak the parts in?
@yt.myworks
10 ай бұрын
I use washing soda from the drugstore or, most recently, Cafiza.
@doctornachman
5 ай бұрын
Is that the same as baking soda in the US? @@yt.myworks
@doctornachman
5 ай бұрын
@yt.myworks,please ignore my previous question, I found cafiza on Amazon...looks similar to the cleaning tablets I get from Jura. Thank you for the video. I now have the courage to clean the spouts on my c60. I thought I was going to have to ship it back to Jura for service.
@censirosa5338
11 ай бұрын
Merci c est sympa 👍
@bernhardsummer9392
4 ай бұрын
Thank you very much
@werekorden
10 ай бұрын
Great Video, you know which information are important and don't waste time on stupid balbla. Thx.
@smrsmr5403
Жыл бұрын
Where in the video did you clean the tamper and holder that holds the espresso grounds?
@yt.myworks
Жыл бұрын
Almost everything can be seen in this video kzitem.info/news/bejne/sZlsmXesrHhofX4
@kidscancompost
8 ай бұрын
How often do u have to do this?
@yt.myworks
8 ай бұрын
I clean the coffee spout together with the brewing group, i.e. every two years when the casing is open. However, if necessary, you can occasionally clean the openings from below with a small brush.
@DaveSchulze
24 күн бұрын
What is that screwdriver bit at 1:02? I’m stuck at that part.
@yt.myworks
22 күн бұрын
amzn.to/4ececzT
@dirkfellner7743
5 ай бұрын
Auf meiner s8 ist noch Garantie, ich werde den teufel tun und die nicht auseinander bauen. Die lass ich reparieren und dann wird die verkauft.!
@alejandrodvazquez5632
Жыл бұрын
Which country are you from ?
@alejandrodvazquez5632
Жыл бұрын
Brazil
@yt.myworks
Жыл бұрын
From Germany my friend 👋😏
@tccycling
Жыл бұрын
Looks complicated as hell. Why can’t Jura make it easy to clean parts that need regular maintenance?!?
Пікірлер: 63