This is such a good video. So much good info and great advice. I'm in the middle of building a KA. I will definitely do this before installing the engine in my wagon since I have a new aftermarket front cover. 👍🏼
@BuildSeason
5 ай бұрын
Awesome! I’m glad it helped!
@danielhughes9556
5 ай бұрын
Hell ya man, I've been watching for a while now. Love the datvacado. I remember that feeling well on my dime.. keep it up. Can't wait to hear It Make choo choo noises
@BuildSeason
5 ай бұрын
Same here! Turbo noises are what it’s all about!
@cmcferin
5 ай бұрын
Congratulations!! This is so amazing and such a great job. Cannot wait to see the next video!
@BuildSeason
5 ай бұрын
Thank you! Hopefully we’ll get some driving footage!
@cmcferin
5 ай бұрын
@@BuildSeason I've got a 69 two door that has sat without an engine for 20 years and this is totally inspiring me to resurrect it!!! Thank you!
@BuildSeason
5 ай бұрын
@cmcferin Glad to hear it! If you want, email me a picture!
@lamboferruccio
5 ай бұрын
You can also use a transmission filling pump to prime your engine but that weed killer pump is a fantastic cheap alternative, oh a good source to connect it is by the oil pressure gauge sensor, T in a fitting and pump away, this goes for all engines.
@BuildSeason
5 ай бұрын
Good tips. Thank you!
@ephatla58
5 ай бұрын
Nice work!
@BuildSeason
5 ай бұрын
Thank you!
@EssMotorsports
5 ай бұрын
I was going to do the same thing with the weed sprayer. Ill have to borrow that!
@BuildSeason
5 ай бұрын
Whenever you need it. It also works for filling transmissions with gear oil.
@ryanbiggs7083
5 ай бұрын
dude, i bet that feels great!
@BuildSeason
5 ай бұрын
Yes it’s an awesome feeling when the engine finally fires up!
@andrewjaeger3720
5 ай бұрын
Yes!
@BuildSeason
5 ай бұрын
Yeah buddy!
@longrodlseries
5 ай бұрын
Congratulations and good work!
@BuildSeason
5 ай бұрын
Thanks a lot! This has been a big project.
@j.wobbly
5 ай бұрын
it lives!!! fuck ya!!! cant wait to see this thing out on the road!!
@BuildSeason
5 ай бұрын
Hopefully it’s on the road soon!
@bernardaborita4631
5 ай бұрын
Yes, that's was great 👍🏽
@christopheradams2678
5 ай бұрын
Fuck yea!! This give me motivation to get my rusty 72 510wagon back on the road I just need to mount a Holley electric fuel pump under the rear seats.
@BuildSeason
5 ай бұрын
That’s awesome! I’m glad to hear these videos are helpful/motivating for others. That alone makes the filming/editing worth it.
@alexj.9268
5 ай бұрын
24:43 'went to the hardware store and got a fitting that fit' this could be really bad as BSPT and NPT are almost identical, you WILL CRACK the aluminum housing if you thread a NPT into a BSPT bung. JDM stuff is generally BSPT as it has more threads and is therefore more better.
@BuildSeason
5 ай бұрын
Thanks for the comment!
@alexj.9268
5 ай бұрын
25:00 if you are trying to get a oil pump to prime just lift the back of the car up in the air causing the oil level to submerge the oil pump.
@BuildSeason
5 ай бұрын
Thanks for the comment!
@hixsfabgarage9926
5 ай бұрын
Hell yah man!!!! 🎉
@BuildSeason
5 ай бұрын
I’m pumped this thing finally runs!
@anthoniehaag7290
5 ай бұрын
What do you half to do to not run a idle air control valve
@BuildSeason
5 ай бұрын
In this case I left the valve disconnected and capped off the hard vacuum line that runs underneath the intake near the throttle body. The idle is then set with the screw on the throttle body, and fine tuned with the VE table and timing table.
@darionherbert8449
5 ай бұрын
Was a bit of a cringe the first half of the video being an auto electrician but it turned out to be a good video. The idle use timing, alot of cars run without iacv and just add timing to keep the idle stable.
@BuildSeason
5 ай бұрын
Thanks for the tip! I’ll keep that in mind trying to get it dialed in.
@RJ_Beam
4 ай бұрын
I runs!
@alexj.9268
5 ай бұрын
I'm very concerned that you dont understand oil pumps and how they work, you know that you could have just OVERFILLED the engine with an additional 5 QTS of oil, which would have submerged the oil pump gears under oil, spin the motor to see pressure on the gauge, drain all, fill properly, done. but good video either way little manlet.
Пікірлер: 38