Hey kids guess what, this isn't the actual review! This is just the installation tutorial, the review will be out in about an hour!!
@wabek5882
3 жыл бұрын
nice
@masonbloomquist2124
3 жыл бұрын
does it have tap? it looked like it had really good tolerances and i expected it to have tap so if there is none im impressed
@WillHirsch
3 жыл бұрын
@@masonbloomquist2124 There is none if done right!
@notes4554
3 жыл бұрын
I'm just here to watch soME HigH QUALITY CONTENT
@Izayoink_Saccuy
3 жыл бұрын
:c
@courtlandvote1419
3 жыл бұрын
I have taken knives apart hundreds of times I didn’t learn anything new from your video but I watched the whole thing just because I love your videos...keep it up bud
@deanmorgan6299
2 жыл бұрын
I already installed the handles, and am still watching it.
@Thewillboxing
3 жыл бұрын
It’s one in the morning I regret nothing
@m4g-nu5ftw92
3 жыл бұрын
meh
@crumpetsupreme3578
3 жыл бұрын
That's a good pathfinder skin in ur avatar
@Thewillboxing
3 жыл бұрын
@@crumpetsupreme3578 thanks friend
@saguanu6584
3 жыл бұрын
Bruh same
@chipmccain.
3 жыл бұрын
@@Thewillboxing I read that in pathfinders voice and I have no idea why
@nanakixiii3
3 жыл бұрын
This video helped me put it together, thank you! HOWEVER FOR OTHER WATCHERS: My Lucha's screws were on the reverse side of my knife compared to Will's, so even if you lay your knife down just like he does in this video, check and make sure you're actually working with the screws, and not the barrels. You might have your screws on the other side of your knife. This does not cause any problems with the mod as a whole, but it'll be really confusing when you keep trying to unscrew your pivots and they never seem to be loosening up. Once I realized that, the mod was far less confusing, and quite easy!
@UniqueApollo
Жыл бұрын
was it the acid washed one?
@FIatfoot
3 жыл бұрын
I'm here because even though I already installed mine I desperately need to see more of Brandon and your antics.
@mrecra8084
2 жыл бұрын
my washers wont fit in what should i do? @Will Hirsch
@jesseosborne6712
3 жыл бұрын
thank you so much i needed this tutorial and you make the tutorial 10000x better 😭
@mr_postit5413
3 жыл бұрын
Been a fan of your channel (no pun intended) for a long time. I never even thought of racing the washers, now my Lucha is God tier! Thanks so much!!
@karabinas
Жыл бұрын
So much easier than disassembling OTF’s…still lookin for springs 3 yrs later.
@troyhitchens5678
2 жыл бұрын
Can't get the 2nd washer in, any tips or suggestions?
@dieselviper7811
2 жыл бұрын
Thanks for this video it’s going to make it a lot easier when I get my new handles
@ryanshaw4289
Жыл бұрын
how did the installation go?
@jaydencarnahan3412
3 жыл бұрын
I there anywhere I can get replacement screws and pivots for it?
@LeviticusMoriarty
Жыл бұрын
is there anywhere to get a full set of hardware and a blade/trainer blade? Flytanium has some pretty rad sandwhich scales, but i dont want to buy a whole ass other knife just to use the scales
@nick6051
3 жыл бұрын
Hi thank for your channel it awesome! I have a quick question. I am upgrading my lucha with the titanium handles and the ceramic washers, do I need to put the other washers
@nick6051
3 жыл бұрын
In as well? Sorry pressed enter before I finished lol
@WillHirsch
3 жыл бұрын
You should have washers between the titanium and the bearings, if that's what you mean!
@nick6051
3 жыл бұрын
@@WillHirsch it is. Thank you.
@frederic_viennot
3 жыл бұрын
awesome !!!!!! so much informations great for a beginner (me ;))
@lucasliveface3474
3 жыл бұрын
Nice video! Do a bear and son knife review
@isaacbuck3107
3 жыл бұрын
No
@lucasliveface3474
3 жыл бұрын
@@isaacbuck3107 😘😘
@pseudo3100
2 жыл бұрын
I just realized that when I reassembled my Lucha a month ago after giving it some lube and loctite I put the handles back on backwards... Don't ask me how because I don't have a clue. I didn't even notice until just now because the handles are basically symmetrical, all it did was reverse the bite and safe handle.
@reedgoodburn9878
3 жыл бұрын
Hi
@teleportedbread6194
3 жыл бұрын
Hello
@m4g-nu5ftw92
3 жыл бұрын
hey
@shinethe_light4644
3 жыл бұрын
Uhh this comment is a day old
@m4g-nu5ftw92
3 жыл бұрын
@@shinethe_light4644 Patreon member
@shinethe_light4644
3 жыл бұрын
@@m4g-nu5ftw92 I see
@Thatonesniper23
3 жыл бұрын
My second washer doesn't fit. Any idea how to fix that?
@dylanhines1140
2 жыл бұрын
i have the same problem. did you ever find a solution
@Thatonesniper23
2 жыл бұрын
@@dylanhines1140 had to mail it in to flytanium to do it for me. They never stated if there was a problem or what the problem was but they put the handles on and mailed it back. Hope this helped
@mizzlecarabizzle142
3 жыл бұрын
I placed the washer between the knife and the bearing opposed to bearing to handle it works but is it correct??
@garrettbowman8125
3 жыл бұрын
Any suggestions where to buy screws, may or may not have stripped them out...
@moderndaycain
3 жыл бұрын
I would love to know where to get better bearings for my lucha mr hirsch
@random5064
3 жыл бұрын
I don't have washers on my lucha, should I get some?
@atypk3285
3 жыл бұрын
Question : Do I absolutely need to loctite my knife, even if I don't mind tightening it often ? I heard it prevents corrosion and stuff, but is it really mandatory ? Thanks !
@hohanrodanrodan9624
3 жыл бұрын
On a Bali it’s a good idea, I’ve lost a few screws.
@LDmagnum
2 жыл бұрын
No its not
@user-uz3sg7ef6h
2 жыл бұрын
No, but without loctite your screws are prone to fall out.
@Skyman-db1rw
Жыл бұрын
I feel like a Jedi building my lightsaber lol
@WillHirsch
Жыл бұрын
That's the spirit!
@Skyman-db1rw
Жыл бұрын
@@WillHirsch I had to sandwich the washers…not sure if they made them thicker or I can’t get the right angle…the second handle is giving me hell lol 😂
@Skyman-db1rw
Жыл бұрын
I did it sensei 😊 silver I kinda want to mark the safe handle instead since the bite has the logo on the inside you rock!
@deadlycurse2529
2 жыл бұрын
Can you do this with other Balisongs
@Valentin-vm5of
3 жыл бұрын
I live in sweden where we’re not allowed live blade balisongs without a license but I thought that there would probably be some good tips a for a taking any balisong apart and I was right :)
@edcthug12
3 жыл бұрын
haha, how are those knife laws working out? Such a disgusting thing for your politicians to consider adults nothing more than children unable to safely use a balisong.
@grusive
3 жыл бұрын
Can you do a tutorial on how to take apart the alpha beast and put it back together please
@Squidboy1987
3 жыл бұрын
hello Friends
@m4g-nu5ftw92
3 жыл бұрын
it is your brother hampton
@Squidboy1987
3 жыл бұрын
@@m4g-nu5ftw92 hello hampton
@minty_flips1471
3 жыл бұрын
50 k subscribers let's GO
@heliumbali
3 жыл бұрын
Either There isnt a link for the ceramic bearings in the desc or O cant find it in the ocean of links lol
@billybob-cz8fb
Жыл бұрын
I can't get the second washer in
@austinbronson47
3 жыл бұрын
Where do I buy mods for this knife?! I’m new to the scene, and can’t seem to find a reliable source for parts!
@jh8287
3 жыл бұрын
Flytanium
@ice5018
3 жыл бұрын
Will these work with the Kershaw trainer
@isaacbuck3107
3 жыл бұрын
Ya
@kees5353
3 жыл бұрын
Hola
@m4g-nu5ftw92
3 жыл бұрын
hola amigo
@m4g-nu5ftw92
3 жыл бұрын
i dont speak spanish well lmao
@raylouiebuensalido3327
3 жыл бұрын
Interesting
@VanBur3n
3 жыл бұрын
Flytanium handles are so much better
@denoisd
3 жыл бұрын
Wait why did i receive a notification if its unlisted, im not complaining tho
@bmk506
2 жыл бұрын
How to toast a pop tart coming up next....?..?
@cat-aceksh6639
3 жыл бұрын
I just stab my hand
@DRIFTY7
3 жыл бұрын
oh god im going to get crucified for this. can i install this on the trainer?
@purgatory671
3 жыл бұрын
Yep!
@BLHJ
3 жыл бұрын
pov: someone sent you the link before it was listed
@audreeestandarte4168
3 жыл бұрын
i want the black squiddy please im in dubai
@m4g-nu5ftw92
3 жыл бұрын
why at 1:24 am
@bigbrainflipz1845
3 жыл бұрын
:o
@bar7r4g32
2 жыл бұрын
Bro this isn’t working…. I can’t manage to push the washer pass
@Sin10el
2 жыл бұрын
I can’t get mine on either man. Too tight, can’t get the second washer in. Already broke two bearings
@bar7r4g32
2 жыл бұрын
@@Sin10el I’m saying… I wonder if other had the same problem and what did they do to bypass it.
@Sin10el
2 жыл бұрын
@@bar7r4g32 I figured it out with the help of Reddit. Here’s the method that worked I’m going to paste it below: “Here’s what worked for me. I pinched together the complete set for one hands of washers and bearings in the knife, but in a way that the washers were not directly over the bearings. Half of the washers were off the bears so they would make a small slope, just enough to be able to fit into the handle. Then I slowly forced the handle onto it, making sure that the washers didn’t get too out of line. Then I used a screwdriver to align everything and get the pivot through. Hopefully this was clear, if not I can take apart my ti lucha and send a vid.”
@bar7r4g32
2 жыл бұрын
@@Sin10el thank you bro, I’ll try it out later
@oli4665
3 жыл бұрын
Pov: you got here through the notifications when it was meant for patreons
@pietanicev1044
3 жыл бұрын
it all makes sense now
@WillHirsch
3 жыл бұрын
This isn't the review, it's an installation tutorial meant for everyone!
@oli4665
3 жыл бұрын
@@WillHirsch Oh thank god 😂
@andylim9785
3 жыл бұрын
Shout out to all my yoyo and bali players. I see the regen pro
@landenle_vrandmore4350
3 жыл бұрын
i got in through the notifications, i shouldn't be here...
@bonasera4094
3 жыл бұрын
Yes you should
@danlee-andel955
2 жыл бұрын
I purchased the Kersha Lucha Trainer and the Flytanium handles together. funny thing, my trainer did not have washers installed. It was tuned perfectly, but it is heavy. the bearings came out deep side, and flat side, out. I assembled all bearings deep side toward the blade, but it does not make a difference. I installed the washers that came with the handles. YES they are a tight fit. I have a mechanical background with Aircraft, Cars, Motorcycles. the washers just don't slide in with finger pressure, NOPE! I use some tape on the handle to prevent scratching on my bran new handles. I placed the handle in a small vice, tighten just enough to prevent movement when pressing in the second washer with a new flat screwdriver. while holding the washer between my fingers with my left hand. DO NOT STAB YOURSELF WITH THE SCREWDRIVER! the screwdriver must have a flat face on the tip. if it is worn or rounded off it will just slip off the washer. Push strait back towards the handle. I used a small drift punch to line up the washer with the barrel and installed the screw with Blue Threadlocker. After turning the handles for 10 minutes and final tuning, It came out perfect! Hope this helps.
@hudsonkim1419
3 жыл бұрын
The instruction don’t make sense what part do I learn how to unlodge the blade from my shin
@sboxsixguv3373
3 жыл бұрын
you shuold make a moding tutorial for the 51.
@kaliumnitraat
3 жыл бұрын
Will has a serious beef with the 51 so i dont think thats gonna happen
@sboxsixguv3373
3 жыл бұрын
@@kaliumnitraat yeah i know but he still owns two.
@makeitsimple1894
3 жыл бұрын
Its super convoluted and difficult
@applesz5921
3 жыл бұрын
Gday
@deandrehenry5259
Жыл бұрын
Witch side do you put the barring on the smooth side towards the knife or the open side on the knife
@deandrehenry5259
Жыл бұрын
@WillHirsch
@mauralowrie5274
Жыл бұрын
Hey Will - I just found your channel. I'm new to flipping. Im starting with a Vulp and a Lucha for my live blade. I just installed the Flyti Europa handles. They did not come with washers. When I tighten the pivot screws all the way, the blade can't swing freely unless I back the screws off. Is this because I don't have washers or a tuning issue?
@Adam-yf8xi
3 жыл бұрын
I'm waiting for these to restock and hopefully I could buy one before the go out of stock
@whyterhyno17
3 жыл бұрын
Very helpful, will come in handy when my titanium scales come. Thanks a lot man
@oveson88
3 жыл бұрын
This just helped me sooooo much. I had to send my whole knife to flytanium for them to tune lol.
@SpasmFingers
3 жыл бұрын
Wonderfully thorough.
@markkeegan2137
2 жыл бұрын
There is a side of the bearings that has a groove and one that is flat what side goes facing the blade?
@carinagarneau1595
3 жыл бұрын
« Why are you here, go away » Bro the recomendation brought me here
@cactusthingsdaily7552
2 жыл бұрын
Do I need to locktite both screws?
@eab643
2 жыл бұрын
the other handle was tighter than the other and destroyed the ceramic bearings, and when i switched back to the originals they went in smoother. they also run smoother compared to the ceramic ones that didn't break. so do not buy the ceramic bearings, they are a waste of money.
@LightofRyga
11 ай бұрын
Do the bearings go up or down? Why are the camera angles so bad? I can't see what he is doing.
@jackzack3675
3 жыл бұрын
Pog
@ItzZed
3 жыл бұрын
Does this have a trainer version? Or something similar that would be legal in Canada?
@aketchy2244
3 жыл бұрын
nope
@sboxsixguv3373
3 жыл бұрын
yes it has it just came out:)
@WillHirsch
3 жыл бұрын
It actually does now!
@anon6952
5 ай бұрын
Bali noob here. This is exactly what I was looking for. Gonna install my sage green flytanium handles tonight. Can’t wait to spill my own blood!
@scottvannewkirk2749
Жыл бұрын
I put some of these on my sons trainer and the second washer was so difficult to get in there. I had to hammer them in with a small flathead and my lucha. Anyone have any suggestions for making the handles less grippy? They feel like sand paper. They look cool and make the knife much lighter. That’s a plus.
@prod.sardoniiq6942
3 жыл бұрын
it says unlisted was I not supposed to watch this
@prod.sardoniiq6942
3 жыл бұрын
I have learned illegal information
@somethingtrulyhorrifying
3 жыл бұрын
@@prod.sardoniiq6942 They're coming for you...you know too much. They already came for me, but I told them I didn't know what they were talking about, so I told them your address instead. Sorry but they're coming and there's nothing I can do about it now. If you have a Lucha, I recommend sleeping with it under your pillow tonight, good luck.
@prod.sardoniiq6942
3 жыл бұрын
@@somethingtrulyhorrifying oh god oh fuck
@WillHirsch
3 жыл бұрын
It's unlisted because it's not the main review, it's something that'll be linked to from the main review!
@yummowickerchimp9749
2 жыл бұрын
Actual footage of a Jedi building a lightsaber
@cotto1hunded
2 жыл бұрын
I just got my orange scales today...they look nothing like your,they're damn near brown 😑
@GideonConley
3 жыл бұрын
I hope you know this is the first instal video on KZitem
@valiumshatner333
Жыл бұрын
Soooo I put the lock tite on before I did the play with the handles for 5 minutes thing. Should this matter? 😅
@bloodyvibe467
Жыл бұрын
My bite handle squeaks so bad so I keep racing it or add lube just assembled a day ago been cranking it for id say about a solid straight hour do I get oil
@d4c935
2 жыл бұрын
I can't get the washer to slide in.
@dylanhines1140
2 жыл бұрын
same problem i have. have you found a solution?
@eduardsklyanin8541
2 жыл бұрын
@@dylanhines1140 you're gonna have to go about it in a different way. basically put the bearings and washers on both sides of the blade and start sliding it on, soon as you see the pivot hole through the handles with both the bearings and washers use something like a screwdriver to move it into position. it's a very rough method but it worked for me, also make sure you keep the bearing from lifting off of the knife cause the washer will want to push it down and lift it off.
@eduardsklyanin8541
2 жыл бұрын
I replied to the dude below hope it sorta helps
@dylanhines1140
2 жыл бұрын
@@eduardsklyanin8541 Like two hours later i eventually got it to fit in using the same method you just said. Thanks for the reply though!
@Joozybalwys
7 ай бұрын
My blade is rubbing against the side when it closes why tf is it doing that
@jamesamescua8647
11 ай бұрын
When I installed the handles my blade is off center is that normal
@ernbtw3969
10 ай бұрын
Proceeds to immediately mismatch the hardware 😂
@nickschu9057
10 ай бұрын
stripped my pivot screw trying to race the washers ;-;
@extratoastable5678
2 жыл бұрын
washers wwont fit
@purpledcabbage
3 жыл бұрын
this is relaxing to watch. i don't even own a lucha
@shinethe_light4644
3 жыл бұрын
Hello!!
@m4g-nu5ftw92
3 жыл бұрын
hi
@hey21139
3 жыл бұрын
ur the best
@GunterGrimm
3 жыл бұрын
Thank you for the detailed instructional guide!
@milkytoast3176
3 жыл бұрын
Is that a replay yoyo on the table
@rnkmode1876
3 жыл бұрын
I ordered a Lucha yesterday, is it a definite positive to remove the Latch?.
@XMeTaLLicAx666X
3 жыл бұрын
Yes. I just removed mine just awhile ago and it sounds and feels way better.
@crumpetsupreme3578
3 жыл бұрын
Tell penny I said hi
@fishedhook2697
3 жыл бұрын
Do you know a better trainer than the andux I can’t buy an actual balisong since I’m aussie
@fishedhook2697
3 жыл бұрын
Btw I know this video is unrelated to this comment but I just found this video in my recommendation
@RingOfShameful
Жыл бұрын
Is that a sage yoyo on ur table
@sketybel1
2 жыл бұрын
The tolerance is so tight that there is no tap even loose, but the method in the video doesn't work anymore. What I had to do today was pinch both bearings and washers, but the washers were off center so they go into the handle first. Then use that lever pressure to slowly ease it in. Once it was close I used an eyeglass screwdriver to line it up. I got the trainer because I like the blade design. This is now my favorite!!! It was clunky with the stock handles, now it's perfect!
@Skyman-db1rw
Жыл бұрын
Yeah dude I can’t force the last washer…so sandwiching them was the only way…now the bite handle is frustrating me so Im taking a break lol 😂
@firstnamelastname6216
9 ай бұрын
did you end up getting it?@@Skyman-db1rw
@jayklemmensen9141
Жыл бұрын
Pivot screw on the safe handle won't move no matter what I do, driving me crazy, only gets tighter. I'm unscrewing on the same side and in the same direction and I cannot get it to budge
@WillHirsch
Жыл бұрын
Make sure you squeeze the handles very tightly while you are unscrewing it and rescrewing it in!
@alejandroechevarria7340
3 жыл бұрын
how do you know which ones the bite handle if it doesnt have a latch?
@famousruwolf565
3 жыл бұрын
Look at the blade
@briankirsch6161
2 жыл бұрын
Theres a Logo on one handle, or tape up the bottom of the bite handle
@_Smiddy_
3 жыл бұрын
9:11 what’s this song? I can’t find it anywhere but I know I’ve heard it before on Spotify EDIT::: I finally found the song, it’s called “humble” by Harris heller
@bigbrainflipz1845
3 жыл бұрын
Fun fact: the cracks on the table was caused by the planarian review where he stabbed his table
@SenkoLoaf
3 жыл бұрын
Those are just checks in the wood. It's something that happens to wood as it dries. You can tell that it's checking because it's along the growth lines, and not just a straight crack
@bigbrainflipz1845
3 жыл бұрын
@@SenkoLoaf you do know that I’m being sarcastic right?
@SenkoLoaf
3 жыл бұрын
@@bigbrainflipz1845 that's some good sarcasm my dude
@bigbrainflipz1845
3 жыл бұрын
@@SenkoLoaf lol yes
@dominicminerva50
2 жыл бұрын
Are you able to use the new washers for the aluminum handles with the stock handle? I have the upgraded bearings from flytanium installed, with my stock handles.
@averagefrog_consumer6980
Жыл бұрын
everything went smooth except for the second washer. i had to use much brute force which in the end worked but it felt pretty wrong since i used a variety of wood type objects because my hand was too soft to get the washer in. Works perfectly now tho thx for this awesome video
@Blotter_Boy
2 жыл бұрын
Skiff berings?
@FrankieKato149
3 жыл бұрын
Where u buy the washers the good ones?
@Adam-yf8xi
2 жыл бұрын
Anyone know where I could buy a replacement t8 pivot screw for the lucha I lost mine
@klimo13
3 жыл бұрын
Your videos and quality are always excellent, I saw that yoyo can we get a yoyo collection video if you have one or a little teaser in another videos.
Пікірлер: 234