Absolutely best video and it works I did exactly what you said and mine has been perfect thank you
@alottagurth2265
2 жыл бұрын
Awesome glad it worked!!
@nathanmccumber8965
4 ай бұрын
@@alottagurth2265what is your neighbor build
@henryhenry4377
Жыл бұрын
Hi i enjoyed your video.can you give description of that conector to knock senser to block .will your setup still work the same as been under the manifold .TY.
@henryhenry4377
Жыл бұрын
Hi I enjoyed your video .just wondering it's been a year since you relocated the knock senser bank 2 is it still working.Ty.
@alottagurth2265
10 ай бұрын
Yes still perfect
@Ike-qo3yh
Жыл бұрын
You are a 5.3 god! Thinks 🙏
@alottagurth2265
10 ай бұрын
Glad I could help
@urielvallin8077
10 ай бұрын
Good video my question is my engine is making a knocking sound when I started in I hate it this sensor is the one responsible for this noise engine no over heating engine is fine just when I started in the morning what you guys think
@bobbyboucher7854
9 ай бұрын
Is it a ticking noise?
@alottagurth2265
9 ай бұрын
That sounds more like a lifter ticking which is a common issue with the gm 5.3 engines
@jamieherrington9826
8 ай бұрын
What’s your oil pressure. High mileage engines the O ring on the oil pickup tube goes bad. Once I replaced mine my ticking/engine noise went away. One way to test to see if it’s your o ring close to next oil change add a couple extra quarts of oil to engine jack the rear of your vehicle up if your ticking/engine stops it’s your o ring.
@mitchellmontesano8769
4 ай бұрын
I get both codes on my 03 tahoe even after replacing both the correct way. I bought the 2 sensor harness from Rock Auto, and I'm going to install the new ones on the outside this time
@alottagurth2265
4 ай бұрын
Good luck bro let me know if it works ! I tried repairing mine the correct way first. But this turned out to work for me
@ArmanMnatsakanyan
Күн бұрын
Damn! I did the exact same thing to my 05 Escalade, bought AC Delco sensors and wiring harness from Rock Auto. They worked for a few months and I got check engine light back after with the same codes: I tested the sensors for resistance, they measure within specs. Tested the wire and it was fine. Now the only other thing to test is the wire from the sensors to the computer (ECM, BCM or whatever it is). Getting sick of it already!
@Dmkpit401
11 ай бұрын
that is chevy wiring it i ever saw it, did you ever test and see if sensor was bad
@alottagurth2265
10 ай бұрын
Sensors were good
@TonyJohnson-t6c
4 ай бұрын
No disrespect, but I don’t like channels where they talk about what they did. SHOW ME WHAT YOU DID. That’s what KZitem is for. 😂😂😂 To be more successful on KZitem you gotta show people bro. Like I said bro I’m a KZitem junky so I KZitem everything. Glad whatever you did worked for you. 💯💯💯🐊🐊🐊
@bobbyboucher7854
9 ай бұрын
Did you end up torquing the sensor or has it still been working off hand tight?
@alottagurth2265
9 ай бұрын
I did not torque to specs. Has been fine
@Jrgunner
Жыл бұрын
I have the same exact problem going on in my 02 Silverado HD 6.0L!!! I'm so frustrated, this will solve my PO332 code, but can anyone help me with a PO327 code?! I'm at my wits end. 😮💨
@bobbyboucher7854
9 ай бұрын
You can always bypass both sensors onto one. So if you relocate the knock sensor like how he did in the video and run the harness back to the connector. You can put wire nuts on both the green and blue coming from the ecm connector which will trick the ecm onto that new relocated sensor
@jasonhicks767
2 жыл бұрын
I’m having the same problem. Any problems since you switched it?
@alottagurth2265
2 жыл бұрын
Works flawlessly still no engine light ! Runs better than it has in years I hope this helps you
@JuanMoreno-l9n
Жыл бұрын
Link for knock sensor I can’t find a single one they all come in pairs
@infiniti_fxvq4602
9 ай бұрын
What kind of wire did you use to extend ? So my issue is with bank 1 .
@alottagurth2265
9 ай бұрын
Just bought standard wire from oreilly auto
@bobbyboucher7854
9 ай бұрын
Any updates?
@alottagurth2265
8 ай бұрын
Still going strong 💪🏽
@shawnmilligan9605
Жыл бұрын
Any updates? Has it thrown a code since this fix?
@alottagurth2265
Жыл бұрын
All is still good 💪🏽
@nbazee7474
2 жыл бұрын
Would it pass smog in Cali?
@alottagurth2265
2 жыл бұрын
Yes! I’m in Cali ! Passed no problem gives no codes
@Billyargueta289
3 ай бұрын
Why not fix it right?
@alottagurth2265
3 ай бұрын
This was after I completely rebuilt the top end and replaced both sensors and harness and still had the same problem. This was my fix to not tear it all apart again for no reason. This fix has been solid for years no issues
@Billyargueta289
3 ай бұрын
@@alottagurth2265 sounds like you didn't fix it right the first time. Makes no sense a new sensor would fail unless you relocated it from its designed position.
@alottagurth2265
3 ай бұрын
@@Billyargueta289 lol
@Billyargueta289
3 ай бұрын
@@alottagurth2265 why not pay a professional if you can't get it right?
@kevinmayes140
2 ай бұрын
@Billyargueta289 apparently you've never owned or worked on these trucks
@prettywomenclassiccars
Жыл бұрын
You only shows one knock where you put the second knoçk
@shawnmilligan9605
Жыл бұрын
He only relocated bank 2 knock sensor. The other one is still in the valley under the intake.
@alottagurth2265
10 ай бұрын
I didn’t move the other one
@SIXPACK110
8 ай бұрын
I recently bypassed 1 sensor. Haven't had any issues since.. More power and way better fuel mileage.. Bad knock sensors will retard your timing.
@alottagurth2265
8 ай бұрын
Yeah man before I figured this out I was dealing with the timing issues and I had to keep deleting the codes but that only lasts a short time lol
@SIXPACK110
8 ай бұрын
@@alottagurth2265 2 months in and I'm still good 03 silverado 4.8 vortec
@jamieherrington9826
8 ай бұрын
There was a guy KZitem that replaced his knock sensors a couple times he finally put both on the outside the engine. It’s hit or miss with brand new ones.
Пікірлер: 52