Best thing I ever did installing a 4 inch spindrifter bottom drain. Thanks again for all my fittings to get the job done
@KoiChronicles
2 жыл бұрын
Thank you Paul, we got there in the end Sir. 🙈 It's great to have you onboard Sir. 🚢🙏🈂️⛩️KC
@stewgordon9291
Жыл бұрын
Thanks man👍 would certainly solvent weld. Double check vale .I know stops return of water could you elaborate a little on where to fit
@KoiChronicles
Жыл бұрын
Thanks stew, ok question on double check vale?? Not too sure I understand the question ❓🙏⛩️🈂️KC
@Mikemkp
2 жыл бұрын
Excellent walk through sir ,wish there was a video like this when I installed my bottom drain ,will be helpful to many people 👍🏻
@KoiChronicles
2 жыл бұрын
Thanks Mike its great to have a closer look #BottomDrain Thanks for dropping in and I hope your all well Sir. 🤙🙏🈂⛩KC
@jolleykoi5970
2 жыл бұрын
Exellent bit of infomation ! 👌🏻👍🏻
@KoiChronicles
2 жыл бұрын
Cheers and thanks for the message Sir, hope you're well #StaySafe. 😎🙏🈂️⛩️
@brianlewis6208
Жыл бұрын
Thanks so much I have always wondered what the gap should be, I have experimented for years thinking it to be much less like 12.5mm now I know.
@KoiChronicles
Жыл бұрын
Hi Brian and thanks for the comment, rule of thumb guide will get the water flowing Sir 💦🙏🈂⛩#StaySafe
@senseibrewster
Жыл бұрын
Do you rec "pre-drilling" the rim holes or just screwing the screws in? Thx!
@KoiChronicles
Жыл бұрын
Hi and thanks for the comment Sir. I'd recommend marking and Pre drilling the holes with the correct sized drill bit to the screws used in question. 🪛🙏⛩️🈂️
@julianchandenier6564
2 жыл бұрын
Excellent, thanks for that got stainless jubilee clips for flex hose do i not need them ?
@KoiChronicles
2 жыл бұрын
Hi Julian you can use the jubilee clips or whatever you're competent in joining the two 10mm air nipples together with the hose. As suggested just a small amount of sealant is my preferred method for #slickness 👌🙏⛩🈂KC
@mykoiobsession
2 жыл бұрын
Would the airline and fittings inside the drain sump impact the water flow in any way? I have a 4" bottom drain om my pond and the air supply comes in from the bottom up through the pipe that supports the lid/diffuser resulting in minimal disruption to the water flow. Works very well.
@KoiChronicles
2 жыл бұрын
I very much doubt it Sir, although yours does sound great. It's designed this way so I'm trying to showcase how and how 'not' to do it. #StaySafe and thank you for your comment✌️🙏⛩️🈂️KC
@richd-koi
2 жыл бұрын
Great vid mate. Are u able to sell a small offcut of 48mm pipe? I've got a 1.5inch non return valve that takes 48mm then i will need to use my rubber boots to get back onto 40mm hard pipe (I have no facebook etc) cheers in advance 👍🐟
@KoiChronicles
2 жыл бұрын
Thanks Rich 👍 and sure thing! Anyone that's made contact with me before have all been satisfied and delt with. I'd be happy to help you Sir. All contact details are over on our website Sir. Thanks again and will look forwards hearing from you. 🕺🙏🈂️⛩️KC
Пікірлер: 18