You're so fast, thanks for a great video! Regarding the component input orientation, I believe one of Matt's intentions was for the Koryuu to be stacked on top the OSSC (at least according to the product description and user-guide), and a really short component cable run would make for a neat combo setup. That way the signal toggle buttons can be accessed from the front. I can see the case being made for both orientations, however. Really glad you managed to show the size difference between the Koryuu and the OSSC, as this hasn't been showcased anywhere prior to this video. I was waiting for your video before making a decision, and will likely pick one up after seeing what future firmware updates will hold.
@MyDudeman222
2 жыл бұрын
I used mine on a toshiba crt with a really bad comb filter that had major chroma delay, introducing tons of color bleed. Using the koryuu as a way to bypass my tv's comb filter through its component ports, it got rid of most of the color bleeding, and looks great for what it is.
@Sirotaca
4 жыл бұрын
Nice review, but you really should have tried the Koryuu+OSSC in generic sampling mode rather than trying to dial in optimal sampling, especially for composite video. With generic sampling it should be capable of results just as good as the RetroTINK solutions.
@WilliamMcCarthyIII
3 жыл бұрын
the optimal timings are what convinced me to buy the koryuu. The N64 quality via s-video is comparable to the Ultra HDMI mod and definitely already beats out RBG modded N64 with generic timings.
@teenx6a6e
3 жыл бұрын
@@WilliamMcCarthyIII You have an N64 modded with Ruth Bader Ginsburg?
@RWL2012
2 жыл бұрын
@@teenx6a6e Red, Blue and Green obviously. Who said it had to be in the right order...?
@eightbit1975
4 жыл бұрын
Perfect device for me...and ordered. Thanks for the review. I am one that uses the OSSC and Retrotink for vintage computers...not consoles. All of the RGB computers (Amiga, ST, etc) work great with the OSSC. But, there are a few (Atari 800, C64, Vic) that either use chroma/luma (s-vid) or composite. I have been using a Retrotink for these and while great, I would like to use these connections with the OSSC benefits. I have been waiting for something like this for a while!
@Sayajiin2
4 жыл бұрын
Really love the format, you really test those device in multiple scenarios. I must say the video production quality went up a big notch as well. Must have take a lot of time to produce. Thank you so much Bob! :)
@RetroTechSelect
4 жыл бұрын
Nice to see a good comparison between this and the TINK 2x. Excellent job of highlighting the strengths of both!
@90shero81
4 жыл бұрын
Retrotink or Rad2x are absolutely the best video processing devices I've ever seen!
@BrandonArnold0
Жыл бұрын
Ohhhh, nice. This will be a good device to have. Thanks for the info
@iCach0
4 жыл бұрын
Love how your videos keep getting better and better! Keep it up!
@ChrisP872
4 жыл бұрын
Great video. I really like your music selections for the background too.
@TKTmon
4 жыл бұрын
6:01 3d print a bracket to stack the two and have a special cable with right angle connectors
@RetroRGB
4 жыл бұрын
Good idea!
@megari4146
4 жыл бұрын
That is a great idea! Just needs to be modeled and figure out the most appropriate components for the connectors and wiring.
@iminimal86
4 жыл бұрын
Thx u dude for all this information. Very helpful every time. Keep doing!!! 👾🛠✌️
@kristopheralonge2813
4 жыл бұрын
That beautiful gcompsw.....
@Ringworm1281
4 жыл бұрын
NGL, the design of the case looks sleek af.. One use I could imagine buying this for would be to get a VCR onto a TV that doesn't accept composite natively.
@wateredwillow
4 жыл бұрын
4:48 The main reason I'm looking at the Koryuu, is my 13 inch 2004 Sony Wega Trinitron KV-13FS110, doesn't have a S-Video input, only coax, composite and component.
@RedLP5000S
4 жыл бұрын
Awesome device. It would surely be less costly than having to mod every composite-only system.
@Robertkopp84
4 жыл бұрын
You can make sandwich and connect them with six 90° adapters. I need something like this with rgb scart out for commodore monitors without composite.
@kennylauderdale_en
4 жыл бұрын
Would you recommend this for VCRs & Laserdiscs?
@RetroRGB
4 жыл бұрын
For watching, yes. Video capture is a bit more complicated with 480i and there isn't an easy answer; It all depends on your capture card setup.
@NUCLEARARMAMENT
4 жыл бұрын
Here's a video sample of a VHS movie using component output, it's also been properly de-interlaced and converted to true progressive footage using 3:2 pulldown reversal to get 23.98p out of the analog NTSC (525/2:1/59.94) signal from the VHS tape: kzitem.info/news/bejne/toiit4incIZ7jYo
@JnL_SSBM
4 жыл бұрын
*This may be perfect for VHS, via S-Video.*
@sickregret
4 жыл бұрын
Ooooo we need that tested!
@mattjcwig
4 жыл бұрын
I can do it, i just need a Koryuu and an svhs vcr 😁
@xmaverickhunterkx
4 жыл бұрын
Anything with S-Video really.
@furiousfox7712
4 жыл бұрын
I got a Retrotink2x PRO, I think I am fine 😜 But happy to see niche holes being filled in the retro gaming community.
@13mikeas
4 жыл бұрын
Do you think it works as well as an OSSC? I keep debating what to get and am getting overwhelmed!
@furiousfox7712
4 жыл бұрын
13mikeas Go with the retrotink2x pro , it is 10 time more user friendly than the ossc
@13mikeas
4 жыл бұрын
@@furiousfox7712 thank you! Ive been researching online and was getting more confused. With the RetroTink do I also need to buy special cables like the HD Retrovision ones? Or can I use stock. It's frustrating because I have several older consoles to connect and I want to make sure I get the most bang for my buck.
@furiousfox7712
4 жыл бұрын
13mikeas Well do you have discord? I got a lot of free time lately so I would rather explain in detail what you need, and the differences betwen cables , scalers , line doublers rather than typing a lot of stuff lol
@jocool7370
4 жыл бұрын
Nice review!? Have you tried the Blue Jeans component cables?
@targetrender9529
10 ай бұрын
I have one off the AliExpress versions of this and it works great. And the Chinese version can be stacked underneath the OSSC since they have the same dimensions. The Chinese “add on board” also has scart output. The Koryuu doesn’t.
@RetroRGB
10 ай бұрын
But it’s a clone. So it’ll probably stop working in a year. Also, please don’t support clone companies - Funding them for this gives them the budget to steal other people’s things.
@targetrender9529
3 ай бұрын
I didn’t know it wasn’t open source. I thought it was like the OSSC. My bad.
@Snivy102
2 жыл бұрын
If I want to use an NES and N64 with this, will it automatically detect which console is powered on and convert that signal to component? (like, if I have both systems plugged into the Koryuu at the same time - NES in composite, N64 in S-video)
@RetroRGB
2 жыл бұрын
No, you'll have to press the button to toggle between the inputs.
@Snivy102
2 жыл бұрын
@@RetroRGB noooooooooo... :( A main selling point is that this can be used to integrate composite/s-video sources into an automatic component switch setup (like the gcomp switch), but if it can't automatically switch between composite and s-video then I'd have to buy one Koryuu for my NES and one for my N64 to keep the seamless console switching :( ...oh well, thank you for your response nonetheless
@cyo_corner
4 жыл бұрын
I think a lot of amiga and commodore consoles cap out at composite and svideo...oh and my FM Towns Marty. I think I'll pick this up at some point :)
@kelvsyc8676
4 жыл бұрын
The only thing I find ugly about the Koryuu is that the output ports are not in the right order, in that they are arranged as "PrYPb" instead of "YPbPr". This creates the impression that the Koryuu converts composite and S-Video into RGsB over RCA cables. While I can understand it for OSSC (where I would presume RGsB is the main use case and YPbPr is a bonus, since the OSSC's other inputs are that way), it is somewhat of a usability issue as not all component cables can change the order of the RCA plugs flexibly. (The YPbPr cable that I connect to my OSSC is noticeably straining because the RCA plug for Pr has to "cross over" the other two, which makes it very difficult to insert without damaging the cable.)
@megari4146
4 жыл бұрын
Yes, this a bit painful for some usage scenarios. The connector is the same as in the OSSC to allow for a stacked setup. The firmware can be modified to output RGsB, and it should also be possible to reassign the mapping of DACs to components to some extent to allow for different connector assignments. However, this doesn't fix the fact that the connectors themselves are color-coded in a certain way.
@zackpetrovic3029
4 жыл бұрын
5:55 right angled joiner?
@tomhanzo2
3 жыл бұрын
I’m thinking of getting this for my Dreamcast. HD Retrovision is never gonna finish the cable.
@hellbillymods45
3 жыл бұрын
And yeah, also because RGB mods don't exist for certain consoles, some are even a struggle to get to composite, such as the SG-1000 model 1 or anything on the first-gen of consoles. If I could, I would RGB everything, but it's just not possible.
@romerolemstra8747
4 жыл бұрын
What is that component scart cable thing you used to connect the Koryuu to the gscart switch?
@sotris99
4 жыл бұрын
Dear Matt all these things you try can also be applied in every analog format? I wan't to buy an OSSC to convert some VHS tapes. Will be a good move or not?
@matstodon
2 жыл бұрын
i've heard this device is not compatible with gbs-control, is that true?
@OpticalHaze
3 жыл бұрын
would this or retro think also be good for interlaced composite video signals from a laserdisc player?
@gaba665
3 жыл бұрын
One question guys: what is the BEST way to connect a PC DVI-I (analog) to a YPbPr CRT TV?..
@mays_hayes
4 жыл бұрын
What capture card were you using for the Koryuu and OSSC? I have the Elgato HD60S. There’s another video on KZitem that works with it, but I’m looking to see if another capture card has worked. Thanks!
@RetroRGB
4 жыл бұрын
kzitem.info/news/bejne/t3-dnZ-EjpOAqIo
@thorw4ld
4 жыл бұрын
first time I hear about "dialing in" the image. How and when is this necessary to do it?
@Retro_Royal
4 жыл бұрын
Imagine you are very bored, and you need to fiddle with otherwise good settings.
@The8BitDuke
4 жыл бұрын
Are you referring to the phase degree adjustment at 2:45? It is an adjustment to the regen. pixel clock of the OSSC and is the last step once you do the sync and low pass filter. If you don't use optimal timings and just use the generic, which are still great on the OSSC, you don't need to do this. Every console - literally - will have a different phase IME, so you'll have to adjust them on your own hardware if you use FBX's profiles, tho using the grid on the 240p test suite like Bob is doing here makes it a quick adjustment!
@chchris25
3 жыл бұрын
My CRT has component but no S-video. Should I buy this transcoder? Or should I use my RetroTINK with an HDMI to component converter in passthrough? Which option will give me the better picture?
@RetroRGB
3 жыл бұрын
If you already have a RetroTINK, it'll be much cheaper to just pick up an HDMI to Component Video converter. Light guns definitely won't work with the RetroTINK though. I'm not sure about the Koryuu - I totally forgot to try when making this video! Here's some converters: www.amazon.com/shop/retrorgb?listId=IP72N6BL06SV
@chchris25
3 жыл бұрын
@@RetroRGB Thanks for the reply. My only concern with using these HDMI to component converters is the resolution. Do these support 240p? Or is the lowest resolution 480i? Since I’m going to a CRT TV, will this interlace my 240p content? What happens if I set the RetroTINK to passthrough?
@jordanmillraney5481
3 жыл бұрын
@@chchris25 it’s really hard to say since I don’t own this converter but my guess is that it will interlace 240p content to form into 480i. To answer your second question, when you set your retrotink to passthrough when 240p content is fed through, then it will simply just passthrough 240p without making any picture modification.
@goukigod
4 жыл бұрын
What are you using to capture 5X from the OSSC?
@RetroRGB
4 жыл бұрын
Datapath Vision E1S. There's more info on it here: www.retrorgb.com/videocapture.html ...and here: kzitem.info/news/bejne/t3-dnZ-EjpOAqIo
@Sinisteve
4 жыл бұрын
Would this work with an extron switcher? I see that that there is no sync?
@RetroRGB
4 жыл бұрын
It should, as almost all Extron switches are compatible with the YPbPr component video this outputs.
@BambooShadow
4 жыл бұрын
3:45 Does the HDMI-to-YPbPr Converter add lag or distort the signal? In the first RetroTINK-2x Video, Mike recommend using a HDMI to VGA (passive?) converter and use the VGA-In on the OSSC instead of the Component in. Is the setup shown here beneficial?
@RetroRGB
4 жыл бұрын
Excellent question - Zero lag (less than 1ms, so we can consider it 'zero') and as long as you get one with the right chip, the signal is fine. Also, the OSSC doesn't allow for a low-pass filter on the VGA port, which means the signal will look cleaner through the component video port. I'll have a more detailed video on this soon.
@BambooShadow
4 жыл бұрын
@@RetroRGB Thanks for your feedback and as always huge thanks for your great work! Looking forward to be hearing more on this.
@velosiped135
4 жыл бұрын
Question, I have multiple composite/s-video consoles. What would be the best way to get these 2-3 inputs to my Koryuu, and then on to my OSSC? Thanks!
@RetroRGB
4 жыл бұрын
Find yourself a used, but really high quality composite & S-Video switch on eBay. Not the $20 Radio Shack junk, stuff that used to be "pro" gear that you can find cheap these days.
@Microwave414
3 жыл бұрын
My only dislike is that it converts these signals to component which is mildly annoying enough that I just bought a retrotink pro over it and decided to just add another line doubler to my setup on top of the OSSC. I'm sure it works very well and all but unplugging and re-plugging in component wires is kind of annoying when you have more than two machines that use component while scart is certainly takes less effort to manage and less clutter.
@trydowave
3 жыл бұрын
can i use this to plug a c64 straight into a sony bvm? Do I need any extra cables or hardware or is this it? I run my devices via bnc through an Extron switcher.
@RetroRGB
3 жыл бұрын
You'd only need RCA to BNC adapters, which are really cheap.
@trydowave
3 жыл бұрын
@@RetroRGB hi again.. id like to ask about component (YPbPr) (on the back of the Koryuu. i think you recommended me this device to me over on FB) and how that plugs into the Extron? Will component go to rgb with no sync or conversion issues?
@SparksNZeros
4 жыл бұрын
the quality of the product is great but i can't help but think the target market for it are the very same people who are already dedicating a lot of money to this hobby and would just hold off till they could afford an rgb mod solution for the few consoles this device serves.
@epy0nkaru
4 жыл бұрын
I'm sorry, I was under the impression that I could simply get an S-video splitter to YPb in a gcompsw and plug that into the retro-tink to get S-video from my n64 to an HDMI port. Is this not the case?
@RetroRGB
4 жыл бұрын
I've never tried that. If it works, there's no "signal conversion" going on though - You're just using the YPb connectors to pass an S-Video signal, then need to wire it properly on the output end.
@christuckwell3185
4 жыл бұрын
Does anyone know if the Koryuu going to have scart output in the future?
@jordanmillraney5481
3 жыл бұрын
There’s really only one step to getting SCART output out of the Koryuu and that is converting it. Just get a component to SCART adapter and it should work. That’s really the only possible way to get the SCART output out of the Koryuu.
@lucky5311
4 жыл бұрын
woah, what's that sweet-looking case on the gcompsw?
@lukasperuzovic1429
4 жыл бұрын
He has a custom metal case on his gcompsw.
@caps-thetechenthusiasticgu812
4 жыл бұрын
Right. He’s asking where he bought it.
@RWL2012
2 жыл бұрын
@@caps-thetechenthusiasticgu812 they didn't though
@gregjarvis1232
4 жыл бұрын
Hi Rob What setup would you recommend for rf composite s video component to hd tv not 4k tv
@RetroRGB
4 жыл бұрын
I'd recommend the RetroTINK2x or 2x Pro. For RF, get a cheap, old VCR, connect the RF to that and output composite to the TINK2x.
@jordanmillraney5481
3 жыл бұрын
The RF signal or cable is basically useless in the retro gaming community because of its fuzziness and graininess in picture quality.
@39zack
4 жыл бұрын
The only thing I don't like about the ossc and this one is the open board design
@joe9592
4 жыл бұрын
Hello Bob. I currently have a Retrotink 2x Pro. I'm looking at getting a OSSC. I'm running all my system through S-Video. Would the koryuu be a better option. It will remove the need for the converter. Thanks
@RetroRGB
4 жыл бұрын
It all depends on how you plan on using the OSSC. If you'd just like to "set it and forget it", then keep the TINK2x Pro and just get an HDMI to component converter. It'll look awesome. ...but if you want to use custom timings, tweak based on TV/Capture card, etc, then the Koryuu should allow for a bit more control.
@joe9592
4 жыл бұрын
@@RetroRGB thanks for the replay. I like less converters and more options. What do you personally like better.
@caivsivlivs
3 жыл бұрын
hey bob no still image for the SMW screen :(
@ABOhiccups
4 жыл бұрын
I want to dump NES ROMs off my NES Game Cartridges (even Homewbrew ROMs that you can't find it on the internet) without illegally downloading ROMs off the internet. Is there any easy to use NES ROM Dumping Tools that you've recommended the most?
@mohamedhussain532
4 жыл бұрын
There's the retrode 2
@brostenen
4 жыл бұрын
Basically.... The device is not finished yet. It is like buying a beta or test release? Second. How long do CRT's keep working these days? The only device you will want to buy, is a device that converts into HDMI. That is the most future proof solution these days.
@voltz15
4 жыл бұрын
God I can remember when shmups claimed we'd just be splitting hairs at this point, but now I'm seeing this is where the new battle ground in video superiority is being drawn. That point was clearly the ossc.
Пікірлер: 96