best channel in KZitem to explain whole k swap.... thank you bro keep it up
@pacific7775
4 жыл бұрын
Man im stoked to hear my kswap start for the first time.. iv been gathering parts for 9 months ...got a k20a2 trans today so stoked ... im hopin to be staring it up in 2 months
@oemworx4147
4 жыл бұрын
Very nice keep at bro. Good luck
@lindaover9764
3 жыл бұрын
I've been running my frank swap on my rsx-s ECU for years. Running cai and shorty header. No issues ever.
@pacific7775
3 жыл бұрын
Hondata does nit like this comment
@eduardopreciado3009
4 жыл бұрын
You make it look so easy. I'm doing one in my ej1 hopefully it goes smooth also. I'm going to study these videos lol
@oemworx4147
4 жыл бұрын
Thank you much appreciated
@randygonzalez9425
4 жыл бұрын
These videos are what I was expecting bro 😎
@oemworx4147
4 жыл бұрын
Thanks bro let me know if there is anything I could help you with.
@ShiftyReaperGaming
Жыл бұрын
How did you install the immobilizer I seen a immobilizer bypass inside a k tuned swap package as well what one did you use?
@bochincheboy
Жыл бұрын
Did you have to put an immobilizer to use that Jdm ecu?
@peterath7347
4 жыл бұрын
Bro I can’t wait to see this at the track!
@oemworx4147
4 жыл бұрын
We will be there soon.
@peterath7347
4 жыл бұрын
What you’ll think it will run in a 1/4 bro
@lifeschoice6235
3 жыл бұрын
LOL those grounds are free, straight into the pockets.
@graftonfrith4555
2 жыл бұрын
Hhhelp help im doing a k24a Ek swap I have a used standard 03 Crv k20a2 37820-pnb-e02 ecu but pump runs but can’t start my swap However a friend ECU start it good so I’m wondering if I have about ECU are it’s just not compatible with the swap
@jawaone2474
2 жыл бұрын
So to my understanding you didn’t ground the yellow and green wire off your ek original harness? You grounded the A wire from your k series conversion harness? Or you don’t have a ek harness in this thing at all?
@jmv.6207
Жыл бұрын
can i hook up the fuel pump direct with grounds i have a tuned k pro but the car won't start ??
@argel1224
2 жыл бұрын
Good day from the Philippines! How do you get around with the multiplex cel code P0600 on the type R PRC ecu? Thanks for the reply. Much appreciated 🙂
@rafiesuhaily5263
2 жыл бұрын
Hi man, thank for the video. Since you doing with the type r ecu may i know which prc model u using on your swap? prc-013 or prc-j01? I got an issue to use the prc-013 to my kswap on my rsx base. FYI, I'm reusing the base wiring no mod and changes are made. Checking through internet if i would like to onboard the kpro on 02-04 model ecu (prc-013) to current swap will require more budget. May i know you thought on this?
@joseguzman7111
4 жыл бұрын
Subscribed. My ep3 k24a swap cranks the same without spark. Should i do a double ground to the gearbox and add a ground to the manifold? I dont think im getting spark due to grounding issues.
@WaifuWya
3 жыл бұрын
i just bought a prc ecu today for my K20A2 integra. its just average FBO’s RBC. will the ecu have all of the functions such as fan switch,temp etc?
@kjerome16
4 жыл бұрын
The wire you ground from the engine harness is it the thick black wire its one black wire bigger than all the others
@dustanadolfson4858
3 жыл бұрын
Do u tap into the wire and ground it or do you depin it and ground it
@jawaone2474
2 жыл бұрын
Much of us need a thorough close up of how you grounded the fuel pump wires. And did you ground A7 and A8 or just one of them? Going through this myself right now?
@gilbertgutierrez8111
4 жыл бұрын
Badass content bro!
@oemworx4147
4 жыл бұрын
Thank bro appreciate it.
@mikeyriv7564
2 жыл бұрын
Do you still need to ground the fuel pump wire if you have hondata installed on the type r ecu?
@stevekeenan9673
3 жыл бұрын
I just got 86 crx and 02 rsx wiring manuals. Got 03 rsx ecu, negative cable, cluster, and engine harness, but gotta blend it with old 0 og carbd ew1 harness. Don't know if I need dash harness, but it's a work in progress
@lowresolution1
3 жыл бұрын
Hi I am looking to swap a k24a3 in my 8th gen sedan. I will be using the stock ecu , i have been told that if i use the stock Ecu the car wont be faster then my existing r18 (may be 5% more performance) . Is this true ? I mean k24a3 is around 200hp while r18 is an economical engine. Can you ease shed some light
@mos25001
4 жыл бұрын
If I put the type S oil pump and the cam gear can I still use the stock Type R ECU daily driver?
@oemworx4147
4 жыл бұрын
Yes. It will be reliable with the mods but can’t go wrong with pump and 50vtc
@krazy_lobito4335
4 жыл бұрын
What do you think about the Haltech Elite 1500... will that ECU work?
@JDMaddictek9
4 жыл бұрын
Hi, how do u read the cel if thr is any on the type r ecu? I’m using the hr conversion harness on my ek and seems like the conversion harness doesn’t come with the obd plug like some of the conversion harness out thr .
@oemworx4147
4 жыл бұрын
The harness I have has it maybe hr made it to where you tap into the original one of the car
@thairicaan
4 жыл бұрын
Dope channel bro👍!! Subscribed 😁
@sbinqnz
2 жыл бұрын
I love ur video, how did u wire up that loose black wire that came in the conversion kit ?
@minibikelife1062
2 жыл бұрын
I have a prc ecu what o2 sensor needs to be used? I have a plm header
@Problemk24
Жыл бұрын
How you got cel to flash for start up?
@billyngo2089
3 жыл бұрын
Did u figure a way to get rid of the check engine light?
@domEk24
4 жыл бұрын
Is this a k24 block?
@MinaTadros1
2 жыл бұрын
Is that a stock ECU or are you running Hondata/ktune?
@bhadz100
4 жыл бұрын
Hey I have a k20A2 and some z1 cams, you think I can run a prc ecu with it?
@oemworx4147
4 жыл бұрын
Yes.
@em1lee606
4 жыл бұрын
Do you still have the type r ecu for sale? If not were is the best place to find one
@gjones2287
4 жыл бұрын
I am running an RBC, I have the drive by wire 03 accord tb, do you know which throttle cable I would need for ek
@oemworx4147
4 жыл бұрын
Stock cable
@gjones2287
4 жыл бұрын
Oem Worx did you have to run a spacer with your setup?
@PolishedMobileDetailing503
4 жыл бұрын
G Jones accord TB bolts directly to rbc
@oemworx4147
4 жыл бұрын
If you pay really close attention to what I said was 2003 Honda Accord DX. there isn’t a 2003 Honda Accord DX in the world with cruise control so you shouldn’t have ran into any issues.
@jonathanscroggins9368
4 жыл бұрын
Is 37820-PRC-013 the correct part number for the ECU?
@oemworx4147
4 жыл бұрын
Yes prc 013 is what you’re looking for.
@jonathanscroggins9368
4 жыл бұрын
Nice!!! I think I just found one for $100. Definitely about to scoop it!!!
@jonathanscroggins9368
4 жыл бұрын
Also bro, I have been following you hardcore!!!! I am working on gathering the parts for my Build and your build has been my go to for everything!!! Keep up the good work man!
@ekaysix61
4 жыл бұрын
Wich ecu do u recommend for daily driven k24a build on a budget. One that wont break the bank. Thanks
@oemworx4147
4 жыл бұрын
Type r ecu
@krazy_lobito4335
4 жыл бұрын
Any build cost $$, like a house for 50k versus a 200k house. Both houses finish 4bedrooms 3baths car garage, done finish... but when a hurricane comes which house its going to be standing, structure foundation its key. .. all builds cost $ & sacrifice. Some builds takes months even years, and how deep its your pocket.
@ekaysix61
4 жыл бұрын
True!!! But I aint building no 8 sec track car. Just a simple daily driven budget street car/ a k24 of course that is all. I've done in the past w/ B series motor and worked perfectly fine, but I understand your point!
@lindaover9764
3 жыл бұрын
I've been running a stock type s ECU for years on my frank swap. No issues ever. Passes smog too
@A2ZREY
2 жыл бұрын
@@lindaover9764 what did you need to run it like key and how did you wire it
@MustafaKhan-ph5hl
4 жыл бұрын
I have a serious problem did a k20a swap in a rsx now i am stuck in limp mode. i am using the type r ecu that came with the car. car wont go over 2.5k
@oemworx4147
4 жыл бұрын
Do you have a cel?
@MustafaKhan-ph5hl
4 жыл бұрын
Oem Worx yea it will not start with the prc ecu its fuel pump idk how to ground it could you please help I have been chasing this for months I don’t need k pro I wana drive it with prc for a while
@MustafaKhan-ph5hl
4 жыл бұрын
Oem Worx i will really appreciate it
@oemworx4147
4 жыл бұрын
The fuel wire from connect e needs to be grounded
@MustafaKhan-ph5hl
4 жыл бұрын
@@oemworx4147 so i grounded the wire and the car runs now but now its revving to 2.5 to 1 like it would if it had a vacuum leak. so i sprayed break clean all around to find a leak no luck. but if you unplug the top sensor of the throttle body (forgot what's it called ) it goes in to limp mode but ideal becomes clean. I am not sure what the issue is yet but i think its to do with the throttle body.
@burrok2475
3 жыл бұрын
If I’m running k pro v4 Prc in a k24a2 do I have to change intake manifold?
@jmv.6207
Жыл бұрын
Yo
@I.aviles07
4 жыл бұрын
@ Oem worx, what is the difference between 37820-PRC-013 k20A and 37820-RBC- J03, k20A both type r ecu?
@oemworx4147
4 жыл бұрын
Big difference just won’t work
@I.aviles07
4 жыл бұрын
Ok thanks @ Oem Worx
@pyang2512
3 жыл бұрын
What is the difference between 02-04 type s and base ecu if im going k pro?
@pacific7775
3 жыл бұрын
Just the reverse lockout
@obdjuan3152
4 жыл бұрын
I can’t get my fuel pump to come on :(
@dustanadolfson4858
3 жыл бұрын
Hi I’m working on wiring my 96 ek k20a ctr kswap some say it’s a16 like you said some say e1 how can I figure out which one to ground on my car and some say Tap in ground some say depin and ground I’m really worried about it I just don’t want to burn up my ecu can u help me find out which one it is for my car thanks so much Dustan
@oemworx4147
3 жыл бұрын
I can’t be anymore clear about how to do it I showed you how and you see the car running.
@dustanadolfson4858
3 жыл бұрын
Thanks for your help I just can’t see in the video if you tapped and grounded with the wire plugged in to the ecu still or u de pinned and grounded ?
@cortez4424
4 жыл бұрын
Can you use any kseries ecu long as it’s manual version?
@PolishedMobileDetailing503
4 жыл бұрын
Nacho with immobilizer deleted you can. The jdm ecu don’t have it
@ejla323
4 жыл бұрын
What bracket is that to make the ecu stand
@oemworx4147
4 жыл бұрын
Stock type r ecu mount
@mrhyspeed8769
3 жыл бұрын
Does he provide tech support??
@skunk3works895
3 жыл бұрын
Is that a stock type r ecu no kproyou could plug and play with that ???
@pacific7775
3 жыл бұрын
Yes
@davidburciaga1139
4 жыл бұрын
Thanks for the video’s I got a problem hope you can help me, I got the same swap just my civic is 97 same ecu but won’t star it crank but no star, I plug my friend kpro v3 and like fire 🔥 stars help me out bro 👍🏼👍🏼
@oemworx4147
4 жыл бұрын
Ground a16 wire and should start right up with the type r ecu
@davidburciaga1139
4 жыл бұрын
Oem Worx I did that was the first thing I did because of your video thanks for replying bro, I got a kpro now so the prc 013 is just collecting dust lol 👍🏼
@oemworx4147
4 жыл бұрын
Would you like to sell it?
@edwinaquino9291
3 жыл бұрын
@@davidburciaga1139 how much for the ecu
@davidburciaga1139
3 жыл бұрын
@@edwinaquino9291 sold mafren
@andersalsdu7980
4 жыл бұрын
How did you bypass the immobilizer? Regards
@oemworx4147
4 жыл бұрын
Type r does not have immobilizer 😉
@andersalsdu7980
4 жыл бұрын
Hi friend, Are you sure they didn't have? Every ep3 I know has a green key symbol in the cluster before the engine starts up. If i understand you right i must only plug the parts like engine, harness and ecu toghter and start up? Many other people said I need a kpro to disable the immobilizer in the kmanager software. Now I'm confused 😖 At first i will try it like you said. Thx for help ✌
@oemworx4147
4 жыл бұрын
Don’t be confused anymore. Look at my car it’s running and showed everything I did to it. Type r ecu does not have immobilizer that’s the reason I made my channel to teach people what I know about Honda kswap
@andersalsdu7980
4 жыл бұрын
Thank you so much for helping. 🙂😎🙂😎✌
@mondellewarren1677
4 жыл бұрын
Oem Worx I have a question I have a k20a2 with the type r ecu I can not get the car to start I have tried the ground
Пікірлер: 107