Wish i would have saw this sooner. It took me a bit to find out where the pv was leaking from. Thanks
@arnaud1033
8 ай бұрын
Top many thanks from France
@Nikolas4g63
Ай бұрын
Hey hello. realy helpful video for the overall procedure but hoping you can help, can i remove the 4 bolts to reapply just silicone since im noticing a leak. and just put it back together(just like 3:44) without dissasembling anything else from the 2 sides?
@ChuckfromTrueTech
Ай бұрын
Yep. Nothing will go flying.
@fox7007
3 ай бұрын
Awesome on this power valve assembly. Everything i needed to know….thanks for making these vids🫡
@MP36BRAVO
5 ай бұрын
On the right side of the cylinder I accidentally removed the zed dimension bolt in the middle instead of the bolt to the right with the spring. What should I do?
@ChuckfromTrueTech
5 ай бұрын
Usually you can see where the bolt was positioning the adjuster. If not you can just reset the Z dimension. No big deal.
@user-fl2ei2bz2c
Жыл бұрын
офигенный ролик
@Bmorrissinging
4 ай бұрын
Can someone help me? I have a 2023 125 XC. Got jug back on but the power valve actuator won’t line up. It won’t line up with the notch to bolt the actuator solenoid back onto the jug. I’m stuck. I’m old school two stroke mechanic guy. Where did the little rod go! lol
@yb6069
2 ай бұрын
What year is yours? Can I do the same with the 2022ktm 300? 49.5??ok?
@ChuckfromTrueTech
2 ай бұрын
Yep. All the TPIs are the same.
@juliandevr1
8 ай бұрын
If i dont take out the bolt on 2:57 do i need to adjust it when putting back together?
@ChuckfromTrueTech
8 ай бұрын
Nope. I definitely recommend checking it either way, but it shouldn’t need to be adjusted if you don’t touch that.
@onthethrottle7104
11 ай бұрын
Not sure I follow the reason for the thread lock to be entered directly onto the threads vs. a little spread on to the bolt and then thread the bolt. I did hear something about air pressure pushing out... I've never used your method, never had any issues with a power valve bolt loosening. I love learning new tricks, though. I would also add, to actively work the power valve up and down as you are performing the installation and especially when you're done adjusting the power valve itself, make sure everything is moving freely and there are no binds or issues.
@ChuckfromTrueTech
11 ай бұрын
It’s a detail, but when things go wrong details matter. In a blind hole the air pressure building as the bolt threads in has to escape through the threads. That pressure escaping will blow the loctite out. If you put it in the hole it won’t blow out because it’s not in the path of airflow.
@onthethrottle7104
11 ай бұрын
@@ChuckfromTrueTech Got it, thanks for the tip!
@jeffb6350
Жыл бұрын
Great video, Chuck. How do you know when you need to send your cylinder in for nikasil coating. Are you using the ring gap measurement to determine that?
@ChuckfromTrueTech
Жыл бұрын
The nikasil is only a few thousands of an inch thick. Once it wears through the coating you'll see aluminum showing through. Usually you'll see this above the exhaust port and at the top of the ring travel. I've got a good example of this coming up on a YZ250 cylinder.
@Prisonmike89
10 ай бұрын
Is it pretty well the same on the 150?
@ChuckfromTrueTech
10 ай бұрын
It’s quite different. Here’s the walkthrough: kzitem.info/news/bejne/w7CFzKJ7j4p7mWksi=hLshd9LbF7BVTRHg
Пікірлер: 20