I made a cradle for my floor jack , so that rear cross over bar has no chance of sliding off the jack ..I took a pipe ...cut 5" long , them cut that into 2 sections. making a C shape. Then I took a 1" pipe nipple and welded it to the bottom center of the C shape cradle. Remove your adapter on your jack...and drop this in its place. Worked for me.
@lmalino695
7 жыл бұрын
Really doesn't look like much of an improvement over just a service jack and stands. Not much of a height improvement and those ramps would be a nuisance for most operations.
@organichemone
3 жыл бұрын
If you built one to hold 6000 lbs, I’d but one in a heartbeat. 5000 lbs just isn’t enough.
@upnorth5465
3 жыл бұрын
That is my biggest reason i haven't bought one. Needs to be able to handle a truck for what it is. I'm thinking either buying one and beefing it up or making my own.
@camerongardner7598
5 жыл бұрын
Anyone know what wheels were on that car in the beginning? Methinks they would look amazing on my c4
@twogunsforme1
3 жыл бұрын
Why didn’t o know about this sooner!! I’m going to make this my next purchase
@davidhumby6658
9 жыл бұрын
where do i get one?
@schl0tte
8 жыл бұрын
No doubt this is made in the USA. Even the wheels of my IKEA office chair do inspire more confidence
@ianbuckle2882
6 жыл бұрын
Imothep i
@specialized29er86
6 жыл бұрын
Still not high enough.
@kitcarr4668
7 жыл бұрын
Seems to me I could have the car jacked up and on high stands ( where I'm free to work on wheels and brakes and have better underside access ) in a fraction of the time it takes to put this thing together. Can't think of a single reason why I'd want one ...
@williambirnbaum1501
4 жыл бұрын
I can relate to your reply...but I just do not trust floor jacks. Seen accidents happen with jacks... Bought one on Craigslist. Glad I did...so will all your Gear Head buddies !! Having this will save you money...not having to see a Doctor $$$$$.
@michaelgribben2002
4 жыл бұрын
@@williambirnbaum1501 Leave it assembled and park on it.
@GunnyNinja
3 жыл бұрын
Because you will have to do all of that again next time... you only have to assemble this once.
@ForensicGuySC
5 жыл бұрын
What do they cost?
@MegaKencam
5 жыл бұрын
$1400 for the base model. Way too much.
@BigJim_909
Жыл бұрын
Can this support a 60-66 C10 with a V8 in it? Does anyone on here know? Thanks.
@STRIKER520
9 жыл бұрын
+Kwik Lift How the hell do you do a brake job on a ramp like it said in the video?
@JohnL9013
9 жыл бұрын
***** Apparently, using the scissor jack included with the car, even though it explicitly states in the owner's manual that those are only to be used in an emergency for tire changes. Make sure you don't use jack stands so that the car falls on you and severs your arm.
@Ali-7676
9 жыл бұрын
***** 2:20-2:26 answers your question.
@302esky
7 жыл бұрын
use a bottle jack on the undercar x member
@TheAkr4m
6 жыл бұрын
302esky yep, use a bottle jack. But this is such a hassle.
@TheAkr4m
6 жыл бұрын
Best thing is to use a jack, lift up vehicle and then put in your safety jack stands. Remove wheels and do your brake service.
Пікірлер: 26