This save me a right ball ache! Another garage set it up wrong and the spring was rubbing on the inner wing! Nice one 🤘
@nw8000
7 жыл бұрын
What tools are you using there please?
@jeffkeith637
5 жыл бұрын
NOTE: The ball joint separator requires forks that are at least 27 mm wide, and the top arm should be of a low profile. Standard vehicle size (19mm) wont get around the ball. Hope that helps.
@mauricebarnett6951
Жыл бұрын
Yes I am in the middle of doing mine, I got all the right tools apart from the ball joint separator. I got one from Machine Mart but it was too small, can't find any places that deal with the 27mm forks. Any links you can point me to would be appreciated. Every bolt has fought against me, tie rods had to be ground off and bolt that holds the shocker to the steering knuckle snapped off so have to see if I can drill that out
@jeffkeith637
Жыл бұрын
@@mauricebarnett6951 I don't know that there is a fork or separator that works. I'm sorry it's a while ago, I think I put the nut back on, screwed it to within a couple of mm of touching, and beat the heck out of it. These cars fight every inch in every job.
@mauricebarnett6951
Жыл бұрын
@@jeffkeith637 thanks anyway, still not finished the job and it's impossible to beat the heck out of the ball joint , drive shafts in the way
@jeffkeith637
Жыл бұрын
@@mauricebarnett6951 it's depressing isn't it. But when you overcome it's great. The wish bones have to be depressed further than seems possible to get the drive shafts out of the back of the hub - LR uses a special tool. I used a three foot long 1 inch galvanised pipe iirc.
@mohtab55
7 жыл бұрын
Anyone fitted this shocks, how do they work compared to OEM?
@raymondsalifya6343
2 жыл бұрын
Do we have kyb shocks for range rover evoque 2013
@mikecarver4322
5 жыл бұрын
Hi what ball joint splitter are you using? My standard one isn’t large enough
@jeffkeith637
5 жыл бұрын
I measured the ball as 27mm, my standard separator forks are only 19mm wide. Darn.
@josemiguelesquibelperez1156
10 ай бұрын
I have a LR2 2008 HSE. What struts does it use my car? Please share the model, series or part number!
@josemiguelesquibelperez1156
Жыл бұрын
Can you share the number or serie of these shocks please?
@francoussi1081
2 жыл бұрын
Hi, Can you clarify the alignment? at 5:35 min, you show that the spring spacer must be rotate by 8° leftwise, is this for the right or the left strut? must the opposite side strut be rotater rightwise by 8°. Many thanks for the video, realy helpful
@ognightingale
9 ай бұрын
I have the same question
@RideBikes_Walkplaces
7 ай бұрын
Did you ever find out this?
@tourvillecharles551
3 жыл бұрын
👍👍👏😁
@RPMHonduras
Жыл бұрын
OMG t e r r i b l e !!! british engineering, you take the whole car apart to replace struts !
@williamrae9954
Жыл бұрын
Ford engineering... Peugeot/Renault much easier...why I do not buy Fords, terrible to work on!
@caintiger
5 жыл бұрын
Is there no sound on this vid???
@Kyb-europe
5 жыл бұрын
No, our videos need to be understood in many languages across Europe, so there is no sound.
Пікірлер: 24